Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41515
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41513
Handle it by creating a new patch for simple database changes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40345
Let the switch start the carrier and set the duplex mode independently
if this nic is up of not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39733
We did not start the PHY when an external phy was in use. Without this
patch the driver uses half duplex mode and the switch uses full duplex
mode, which causes problems.
Thank you fback for spotting this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39719
It was recently sent to linux-mips for comments. It adds workaround for
WNR3500L to enable USB port.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 39469
This breaks some devices where the serial console is not at port 0 but
somewhere else.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39060
The wait instruction is only broken on the BCM4706 and not on the other
similar SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38979
This adds support for vectored interrupts in this SoC.
This is supported by the 74K cpus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38975
bcm47xx misses cpu overwrites for the features of the CPUs used in
these SoCs.
Instead of manually checking, it is now known at compile time for some
options and the compiler is able to remove the checks and optimize the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38974
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:
commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat Apr 6 22:22:26 2013 +0000
brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.
This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
Some devices are using tty1 as the default console, also swap the early
boot console in such case. This is needed for the WGT634U.
Thank you Russell for reporting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38794
boardnum is unstable, so allow using NULL to make it unchecked.
A method for differentiating F7D3301 from F7D3302 using nvram is
unknown at this point. Reading the first 32bits of magic from the
"linux" mtd partition would do the trick, but these 2 are similar
enough that we don't need separate led/button definitions. Not knowing
which one you have is only a usability issue for upgrading the device:
they expect different magic numbers for their trx images.
Signed-off-by: Cody P Schafer <devel@codyps.com>
SVN-Revision: 38767
It is a problem when phydev is not set at this position and not the other way around.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38744
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38699
When the mdio bus is unregistered the newly created phy will also be
unregistered and freed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38539
On some devices with e.g. a BCM2535F switch the second MAC is used, but
we can not find a phy under all addresses between 0 and 31, 0xffffffff
is returned as phy id. If we can not find a phy at the expected address
create a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38538
Without this patch we treated only phy addr 30 as an external phy, but
there is a register to check that. Now we do not have to try to reset
the switch to check for an external switch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38502
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
SVN-Revision: 38312
Early printk was disabled because it caused hangs on some devices, the
old patches were using the CFE console now we use the normal serial
console, it is at a constant address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38309
Add patches like they are currently in the mainline mips tree and add
some more pending patches for board detection.
* Now the board name is shown under machine in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38308
