This is for security precautions. As persist_tun and persist_key are
already there, this should not cause compatibility issue.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 45961
- fix iconv detection because it adds host paths
- disable python detection (host python-config is found)
iconv issue is reported by buildbot config.log + replicated locally
see config.log in logs.tar.gz
python issue observed locally on Arch Linux
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45953
Adds PPP unnumbered support via the parameter unnumbered which points to a logical OpenWRT interface.
The PPP proto shell handler will "borrow" an IP address from the unnumbered interface (if multiple
IP addresses are present the longest prefix different from 32 will be "borrowed") for which a host
interface dependency will be created. Due to the host interface dependency the PPP unnumbered interface
will only "borrow" an IP address from an interface which is up.
The borrowed IP address will be shared as local IP address by the PPP daemon and no other local IP
will be accepted from the peer in the IPCP negotiation.
A typical use case is the usage of a public IP subnet on the Lan interface which will be shared
by the PPP interface as local IP address.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45948
Commit 31214c38c8dd0f70366b523f9b0335145b9386bd removes IPv6 unneeded source-dest-routing workarounds;
as a result sourcerouting parameter is unused and can be removed.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45940
Commit 31214c38c8dd0f70366b523f9b0335145b9386bd removes IPv6 unneeded source-dest-routing workarounds;
as a result sourcerouting parameter is unused and can be removed.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45939
This allows e.g. BCM43602 to work out of box, without dumping a proper
MTD partition to /lib/firmware/ NVRAM file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45931
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45919
Add three download mirrors for 'grub', as the Makefile currently defines only
one download location.
@GNU can not be used, as the most recent version of 'grub' is not available
at the general GNU mirrors, and can only be found at the "gnu-alpha" mirrors.
Signed-off-by: Hannu Nyman <hannu.nyman at iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45909
get_image allows passing 2nd argument that is used in a pipe for
extracting firmware from a non-native format. By accepting such command
in default_do_upgrade we allow platforms to use this helper for vendor
specific images.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45900
trx.c in mtd would not include endian.h, so on systems that do not have
this header implicitly included from the other headers (like musl), both
__BYTE_ORDER and __BIG_ENDIAN would be undefined and thus 0, leading to
it always presuming a big-endian system. this would lead to issues when
running mtd fixtrx on little-endian systems, as it would never recognize
the TRX magic as result of the broken STORE32_LE() macro.
Signed-off-by: Shiz <hi@shiz.me>
Tested-by: Shiz <hi@shiz.me>
SVN-Revision: 45896
These are two new packet schedulers introduced in Linux 3.12 and 3.14
respectively. sch_fq is a perfect fairness queueing scheduler that also
adds pacing on host TCP flows, and sch_pie is an AQM.
Having them available in kmod-sched makes it easier for people to test
these new queueing schemes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
SVN-Revision: 45885
there is a conceptual design flaw in our interface events. workaround this by
disabling duplicate message supression in procd. we need to fix this properly
for the next release
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 45883
This patch is taken from the gentoo guys who extracted this from a large
upstream commit (with many unrelated changes).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45878
this is an ugly hack that will be removed when the netifd maintainers
have time to look at the problem.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 45876
We just moved the stmmac support in the kernel for ipq806x. Therefore,
nobody needs this driver so we'll just get rid of it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45872
Add dependency of kmod-crypto-ecb to kmod-bluetooth to avoid the kernel warning
"Bluetooth: Unable to create crypto context".
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 45860
This prevents auto-detection of libxml2 and thus the error:
Package lldpd is missing dependencies for the following libraries:
libxml2.so.2
Preventing a dependency to libxml2 is preferred, since libxml2
would be a out-of-(core-)tree dependency.
Reported-by: Buildbot
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 45859
Before starting hostapd we create interface for it. The problem is we
try to create STA interface just to let hostapd change it to AP later.
It may fail if device doesn't support STA interfaces or if we already
hit a limit. Consider following phy (it's from BCM43602 and brcmfmac):
$ iw phy phy0 info | tail
valid interface combinations:
* #{ IBSS, managed } <= 1, #{ AP } <= 4, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
Trying to setup 2 interfaces: STA + AP results in:
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): Configuration file: /var/run/hostapd-phy0.conf
radio0 (1101): Could not read interface wlan0-1 flags: No such device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45856
nss-gmac has been replaced by its upstream counterpart "stmmac", to
which we added the SoC glue layer required for it to run on IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45832
This fixes various problems with parsing platform NVRAM. It's required
to get BCM43602 working in most cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45802
This introduces a common macro to assemble the correct url templates to
avoid code duplication and have the feed config handling in a central place.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45799
* Rework hostapd and wpa_supplicant status parsing code
* Add support for querying available HT rates
* Relax definition of restricted channels
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45766
When CONFIG_PER_FEED_REPO_ADD_DISABLED is set, trigger index creation for
any available feed, regardless of whether there where binaries built or not.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45765
Use shared libipt{,4,6}ext.so libraries instead of statically linking
the userspace matches into the fw3 executable.
As a side effect the match initialization is extremely simplified
compared to the weak function pointer juggling performed before.
This also fixes the initialization of the multiport match.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45764
* drop unused lenient restore patch
* instead of statically linking core extensions, build shared libraries
for reuse in fw3
* strip outdated match revisions and aliases to trim down library size
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45758
modules relating to CONFIG_USB_AUDIO
Kernel <2.6.35 is not supported in trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45734
If the first resolveip call will fail, peeraddr will be now empty, and
the subsequent resolveip call will try to resolve an empty string.
Fix this by storing the result in a temporary variable.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45712
3.18.12 backported 61ada528dea028331e99e8ceaed87c683ad25de2 ("sched/wait:
Provide infrastructure to deal with nested blocking") from 3.19, causing
the following error on load:
[ 13.588000] compat: exports duplicate symbol woken_wake_function (owned by kernel)
Fix this by guarding it with a check for 3.18.11 or earlier instead of
3.19.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45710
Instead of stripping everything after the first dot, strip everything
after the last dot.
This fixes pre-/postrm actions for packages with a dot in their name,
like libusb-1.0.
Fixes#19668.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45702
Bump dnsmasq to v2.73rc8
Important - fixes remotely exploitable buffer overflow introduced in all v2.73 test/release candidates.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
SVN-Revision: 45693
hand over parameters to user-script e.g. $1=deconfig
Signed-off-by: Leon George <leon@georgemail.de>
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 45626
fixes compile error:
(observed w. target arm64, all kernel build opts enabled)
error: call to '__open_missing_mode' declared with attribute
error: open with O_CREAT in second argument needs 3 arguments
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45625
The WAN port should at least respond to IGMP and MLD queries as
otherwise a snooping bridge/switch might drop traffic.
RFC4890 recommends to leave IGMP and MLD unfiltered as they are always
link-scoped anyways.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45613
Before r45593 kmod-l2tp-ip did not depend on kmod-ipv6.
With r45593 support for L2TP IPv6 encapsulation was added and
included in the kmod-l2tp-ip package. This change also
added the dependency to kmod-ipv6 to kmod-l2tp-ip, regardless
of whether the user chose to generally include IPv6 support
or not.
Change this so L2TP over IPv6 and the resulting dependency
to kmod-ipv6 is only included in kmod-l2tp-ip if IPv6 support
is enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45612
OpenVPN assumes that its control channel messages are sent and received
unfragmented, this assumption is broken when CBC record splitting is
enabled in mbedTLS.
The record splitting is intended as countermeasure against BEAST attacks
which do not apply to OpenVPN, therefore we simply disable it until
upstream OpenVPN gains the ability to process fragmented control
messages.
Disabling the splitting also works around a (not remotely triggerable)
segmentation fault in mbedTLS.
References:
* https://dev.openwrt.org/ticket/19101
* https://community.openvpn.net/openvpn/ticket/524
* https://github.com/ARMmbed/mbedtls/pull/185
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45602
This reverts commit ff84c27a281bc19df19bc62ee8688cca5586f6e3.
This tool has really broken size handling (many values hardcoded), it
crashes right now in case of NVRAM not filling whole MTD partition.
Conflicts:
package/utils/nvram/src/nvram.h
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45579
This reverts r43204. The symlinks are faulty, as they point to a
temporary staging dir
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45569
For years Broadcom devices use 64 KiB NVRAM partition size and some of
them indeed have it filled in more than 50%. This change allows handling
whole NVRAM e.g. on Netgear WNDR4500 and Netgear R8000.
The same fix was applied to kernel in upstream commit 6ab7c29.
Reported-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45566
We don't have broadcom-diag for months or years now and the correct
solution is to simply don't have "nvram" partition on WGT634U anyway.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45564
Sytax of /proc/mtd is following:
dev: size erasesize name
which means that sscanf "mtd%d: %08x" reads size, not erasesize.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45563
instead of failing when authsae is not installed, also try using
wpa_supplicant as the newly added -mesh variants support mesh mode
and SAE encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45520
The most significant change from the previous version is the trimming of
the 300-ip_tiny.patch to lib/utils.c where a section previously patched
had vanished. That section of the patch was removed.
Built and lightly tested on ar71xx against uClibc and musl.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 45512
Hostapd's control file location was changed in 2013, and that has apparently
broken the wps button hotplug script in cases where there are multiple radios
and wps is possibly configured also for the second radio. The current wps
button hotplug script always handles only the first radio.
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/wps-hotplug.sh
The reason is that the button hotplug script seeks directories like
/var/run/hostapd*, as the hostapd-phy0.conf files were earlier in
per-interface subdirectories.
Currently the *.conf files are directly in /var/run and the control sockets
are in /var/run/hostapd, but there is no subdirectory for each radio.
root@OpenWrt:/# ls /var/run/hostapd*
/var/run/hostapd-phy0.conf /var/run/hostapd-phy1.conf
/var/run/hostapd:
wlan0 wlan1
The hotplug script was attempted to be fixed after the hostapd change by
r38986 in Dec2013, but that change only unbroke the script for the first
radio, but left it broken for multiple radios.
https://dev.openwrt.org/changeset/38986/
The script fails to find subdirectories with [ -d "$dir" ], and passes just
the only found directory /var/run/hostapd, leading into activating only the
first radio, as hostapd_cli defaults to first socket found inthe passed
directory:
root@OpenWrt:/# hostapd_cli -?
...
usage: hostapd_cli [-p<path>] [-i<ifname>] [-hvB] [-a<path>] \
[-G<ping interval>] [command..]
...
-p<path> path to find control sockets (default: /var/run/hostapd)
...
-i<ifname> Interface to listen on (default: first interface found in the
socket path)
Below is a run with the default script and with my proposed solution.
Default script (with logging added):
==================================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
for dir in /var/run/hostapd*; do
[ -d "$dir" ] || continue
logger "WPS activated for: $dir"
hostapd_cli -p "$dir" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Timed-out
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:38:50 2015 user.notice root: WPS activated for: /var/run/hostapd
wlan0 got WPS activated, while wlan1 remained inactive.
I have modified the script to search for sockets instead of directories and
to use the "-i" option with hostapd_cli, and now the script properly
activates wps for both radios. As "-i" needs the interface name instead of
the full path, the script first changes dir to /var/run/hostapd to get simply
the interface names.
Modified script (with logging):
===============================
root@OpenWrt:/# cat /etc/rc.button/wps
#!/bin/sh
if [ "$ACTION" = "pressed" -a "$BUTTON" = "wps" ]; then
cd /var/run/hostapd
for dir in *; do
[ -S "$socket" ] || continue
logger "WPS activated for: $socket"
hostapd_cli -i "$socket" wps_pbc
done
fi
>>>> WPS BUTTON PRESSED <<<<<
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan0 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# hostapd_cli -p /var/run/hostapd -i wlan1 wps_get_status
PBC Status: Active
Last WPS result: None
root@OpenWrt:/# logread | grep WPS
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan0
Tue Apr 14 18:53:06 2015 user.notice root: WPS activated for: wlan1
Both radios got their WPS activated properly.
I am not sure if my solution is optimal, but it seems to work. WPS button is
maybe not that often used functionality, but it might be fixed in any case.
Routers with multiple radios are common now, so the bug is maybe more
prominent than earlier.
The modified script has been in a slightly different format in my community
build since r42420 in September 2014.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45492
The last line of procd.sh has a reference to procd_add_interface_reload. procd_add_interface_reload
doesn't seem to exist. I've removed the reference of it to minimize confusion.
Signed-off-by: Eric Schultz <eschultz@prplfoundation.org>
SVN-Revision: 45487
Depending on configuration, disable the LED before writing the trigger
and enable it after writing it. Fixes LEDs where the value defaults to 1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45463
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
To prevent future confusion around '/overlay' vs. 'overlay' simply reject
relative path specifications as mount points since such paths result in
undefined behaviour anyway.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 45404
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45380
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45379
Fixes build failure caught by buildbot:
IEEE Std 802.15.4 Low-Rate Wireless Personal Area Networks support (IEEE802154) [M/n/y/?] m
6lowpan support over IEEE 802.15.4 (IEEE802154_6LOWPAN) [N/m/?] (NEW) aborted!
Console input/output is redirected. Run 'make oldconfig' to update configuration.
make[6]: *** [silentoldconfig] Error 1
make[5]: *** [silentoldconfig] Error 2
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45357
r45270 removed ieee80211n=%d from the format string but didn't remove
the parameter itself. Though this probably doesn't cause any harm, it's
quite confusing and unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45351
it causes problems with newer iptables when ipv6 is disabled as iptc uncoditionally links ip6tc
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 45350
This patch adds the wpan-tools (iwpan) utility to OpenWRT
build system. This utility required to manage IEE-802.15.4
devices.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
SVN-Revision: 45349
Current NAND sysupgrade process is a bit hard to follow due to the way
of triggering stage1. Currently this is done by leaving a /mark/ in the
form of /tmp/sysupgrade-nand-path during nand_do_platform_check.
Existence of this mark stops standard sysupgrade process (as the result
of sysupgrade_pre_upgrade exit). This may be a bit misleading.
Proposed solution adds a new function that will allow platform.sh
trigger NAND sysupgrade consciously. This will also allow cleaning
nand_do_platform_check limiting it to just checking the image.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45338
- move config symbol to separate package (Why was it there in the first place?)
- 8723au might be used in some USB sticks or on some sunxi boards
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45336
Enables last error support for the PPP protocol handlers.
In generic teardown the PPP daemon exit code is translated into
a self explaining error string which is set as interface error
by proto_notify_error in case of failure.
Signed-off-by: Johan Peeters <johan.peeters111@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45333
this allow us to use syslog tcp with \0 trailer
instead of \n trailer (logread -0 option)
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 45329
Subtarget legacy is supposed to support all ssb SoC except for BCM4705.
There are few BCM4703 devices with 802.11n supprt (WRT160N v1.0, v1.1).
Few BCM4704 devices with 802.11n: ASUS WL-500W, Linksys WRT150N v1.0 &
v1.1, Linksys WRT300N v1.0, Netgear WNDR3300 v1, WNR834B v1 & v2.
It seems we have to enable N-PHY for legacy as well to support above.
Unfortunately it increases root.squashfs size by 48 460 B.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45309
This driver is upstream since 2012 (commit: a8e510f682f), so switch to
it and remove own sources. Also place it under "Network Devices" menu
together with other phy drivers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 45269
The arg argument is missing to the printer call in the print_option
utility when the option flag OPT_A2STRVAL is set.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45264
PPPD crashes (SEGV) when the dump or dryrun options are specified and an option
is internally defined as "o_special" with an option flag of "OPT_A2STRVAL".
As the option value is not saved when the parameter is processed, a reference
to the option will result into a crash (e.g. when printing).
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45263
User might have modified/extended template direct or by LuCI application.
So do not overwrite on update/upgrade.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 45258
Most AP devices out there do not have a properly programmed regulatory
domain code, which means they are limited to US frequencies by default.
This has been a major annoyance for a long time now. Since no fix for
the manfuacturing process seems to be forthcoming, the only sane option
seems to be to allow users to change the country code in such cases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45252
Otherwise procd cannot initialize the watchdog since the module will
be loaded later.
Tested with booke_wdt.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 45239
CONFIG_MFD_OMAP_USB_HOST is needed for working USB on BeagleBoard
tested on BeagleBoard C4 (EBVBeagle)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45236
replaces kmod-usb-serial-motorola-phone it's found only in Kernel <3.12
This module handles many simple USB serial devices
like Motorola Phones, GPS reveivers in Kernels above 3.14
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45233
This module is needed for bluetooth audio playback
with pulseaudio 6 and bluez5.
a working guide can be found in the wiki:
http://wiki.openwrt.org/wiki/bluetooth.audio
(additional packages/modifications are required
and submitted to github feeds)
tested with:
Android mobile (Sony Xperia M) as audio source
TI omap BeagleBoard as audio sink
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45231
This patch backports the option --tftp-no-fail to dnsmasq and prevents the
service from aborting if the specified TFTP root directory is not available;
this might be the case if TFTP files are located on external media that might
occasionally not be present at startup.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 45213