Commit graph

14184 commits

Author SHA1 Message Date
Felix Fietkau
7c5c213621 ar71xx: fix tl-wr710n images (#19692)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45756
2015-05-26 07:13:40 +00:00
Felix Fietkau
9f0ffef86a kirkwood: disable the bogus CONFIG_IP_ADVANCED_ROUTER override (#19722)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45753
2015-05-25 22:59:15 +00:00
Felix Fietkau
7b85e8e316 mpc85xx: TL-WDR4900: Fix port 6 being shown as up (10MBit/half) in LUCI/swconfig
Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.

This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 45749
2015-05-25 21:15:37 +00:00
Jonas Gorski
caea19a3e0 ramips: fix hang on boot on rt305x
Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.

Fixes #19715.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45747
2015-05-25 18:02:32 +00:00
John Crispin
ab84e2d704 octeon: build squashfs image for UBNT ERLITE
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 45732
2015-05-23 15:28:20 +00:00
John Crispin
b4494d9713 ipq806x: enable cpu idle support in kernel conf
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45731
2015-05-23 15:28:11 +00:00
John Crispin
8e49b4b902 ipq806x: add & enable cpufreq support
This change set enables frequency scaling on ipq806x, which speeds-up
the CPU and allows it to achieve its max frequency.

These patches are cherry-picked & backported from the following location:
*130-132: linux-next
*133-143: LKML - https://lkml.org/lkml/2015/3/21/15
*144: derived from other qcom similar dts
*145: derived from https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-3.14/drivers/cpufreq/cpufreq-krait.c

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45730
2015-05-23 15:28:02 +00:00
John Crispin
0b24527e4d ipq806x: add power regulators support
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45729
2015-05-23 15:27:54 +00:00
John Crispin
f74477de48 ipq806x: disable i2c device on gsbi4
Patch cherry-picked from the following location:
https://chromium-review.googlesource.com/#/c/269931/

Disable the i2c device on gsbi4 and mark gsbi4_h and gsbi4_qup clks as
unused. If they are enabled, clock framework will turn them off at end
of probe. On ipq806x by design gsbi4_qup, gsbi4_h clks and i2c on gsbi4
are meant for RPM usage. So turning them off in kernel is incorrect.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45728
2015-05-23 15:27:45 +00:00
John Crispin
1c6d332d8f ipq806x: refresh kernel patches
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45727
2015-05-23 15:27:28 +00:00
John Crispin
66950455b7 ar71xx: Add support for the Meraki MR12 & MR16
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>

SVN-Revision: 45726
2015-05-23 15:27:22 +00:00
John Crispin
870cd41936 rampis: add support for status led on ASUS RT-N14U
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)

Signed-off-by: Matteo Panella <m.panella@level28.org>

SVN-Revision: 45725
2015-05-23 15:27:10 +00:00
John Crispin
9c86abae0e ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile Router
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port.  The original product information can be found at:
http://www.aximcom.com/en/MR-102N

Signed-off-by:	Tai-hwa Liang <atliang@gmail.com>

SVN-Revision: 45724
2015-05-23 15:27:05 +00:00
John Crispin
4810f3f803 ramips: fix switch names for several boards in device tree
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 45723
2015-05-23 15:26:51 +00:00
John Crispin
5e96c2d541 ramips: add support for Comfast CF-WR800N
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45722
2015-05-23 15:26:39 +00:00
John Crispin
230efe318f lantiq: Fix initialization of the PCI IRQs when PCIe is also enabled
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45718
2015-05-23 15:25:59 +00:00
John Crispin
390924e662 lantiq: Fix PCIe bus when PCI is also enabled.
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45717
2015-05-23 15:25:51 +00:00
Hauke Mehrtens
47eca7a1ca bcm53xx: add OHCI (USB 1.1) support
There is also a OHCI controller, activate it for USB 1.1 support.

This should close #19601.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 45716
2015-05-23 14:54:44 +00:00
Jonas Gorski
dc60b7fffa arm64: enable new errata backported to 3.18
3.18.13 introduced a bunch of new errata, enable them to be on the
safe side.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45715
2015-05-22 22:51:37 +00:00
Jonas Gorski
4e2b4d8072 kernel: add missing generic config symbol
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45714
2015-05-22 22:51:34 +00:00
Jonas Gorski
76d079204d kernel: update 3.18 to 3.18.14
Changelogs:

* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.12
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.13
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.14

Build tested on brcm63xx and ipq806x, runtested on brcm63xx.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45711
2015-05-21 19:32:46 +00:00
Jonas Gorski
4bb7b2186e brcm63xx: fix failsafe lan and status led for DSL-274xB rev. F1
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45709
2015-05-21 19:32:00 +00:00
Jonas Gorski
509c3211d6 brcm63xx: Add Huawei HG655b support
This patch adds support for the Huawei HG655b.

Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45708
2015-05-21 19:31:54 +00:00
Steven Barth
53098a8aa5 generic/4.0: fix error during kernel patch application
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
  Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
  patching file net/ipv6/ip6_output.c
  Hunk #1 FAILED at 886.
  1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
  patching file net/ipv6/route.c
  Hunk #1 succeeded at 2247 (offset 2 lines).
  Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)

This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45705
2015-05-20 19:23:33 +00:00
Imre Kaloz
c4c4cce190 mvebu: supress useless in-cpu rtc init on the Mamba
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45704
2015-05-19 22:54:05 +00:00
Steven Barth
1296956908 linux: backport IPv6 SAS fixes for source-specific routes
Signed-off-by: Steven Barth <steven@midlink.org>

SVN-Revision: 45699
2015-05-19 07:43:59 +00:00
Rafał Miłecki
63bb7c51db bcm53xx: add Asus RT-AC87U partitioning hacky workaround
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45694
2015-05-17 12:10:38 +00:00
Rafał Miłecki
75b8e247e3 bcm53xx: try to fix network on Asus RT-AC87U
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).

One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45692
2015-05-16 17:14:25 +00:00
Rafał Miłecki
ab83610563 bcm53xx: use backported Asus RT-AC87U DT patch
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45691
2015-05-16 15:44:00 +00:00
Rafał Miłecki
abed46aacc bcm53xx: enable RT-AC87U UART console
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 45690
2015-05-16 11:45:52 +00:00
Rafał Miłecki
3dd9274332 bcm53xx: add support for SmartRG SR400ac
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45686
2015-05-13 20:01:15 +00:00
Rafał Miłecki
b4ecf19faa bcm53xx: replace DT patches with backports from stblinux
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45685
2015-05-13 20:01:03 +00:00
Rafał Miłecki
af019cad56 bcm53xx: use of_machine_is_compatible helper in b53 fix
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45684
2015-05-13 14:34:23 +00:00
Rafał Miłecki
afb98aea4d bcm53xx: fix "typo" in b53 patch fixing R8000 CPU port
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45683
2015-05-13 13:12:57 +00:00
Rafał Miłecki
610ee0d85a bcm53xx: add b53 hacky workaround for Netgear R8000 CPU port
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45682
2015-05-13 13:11:17 +00:00
Rafał Miłecki
2d3aaa2d2f bcm53xx: fix default network interface on Netgear R8000
It has 3 Ethernet interfaces, each of them connected to separated switch
port. Default NVRAM uses switch port 8 as CPU which is connected to the
3rd interface (eth2).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45681
2015-05-13 13:11:04 +00:00
Rafał Miłecki
45ec92fa30 bcm53xx: bgmac: add support for the 3rd core
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45680
2015-05-13 13:11:00 +00:00
Rafał Miłecki
d2e5e2bf54 bcm53xx: sync NVRAM and SPROM drivers with upstream version
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45678
2015-05-13 08:30:45 +00:00
Rafał Miłecki
260383aeb1 kernel: backport struct ssb_sprom changes submitted by MIPS tree
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45677
2015-05-13 07:52:43 +00:00
Rafał Miłecki
e93c68eedd b53: Allow using all ports on BCM53012
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45676
2015-05-12 13:18:53 +00:00
Felix Fietkau
6ceb1b0358 ar71xx: convert tl-wr741nd v1/v2 to new image building code, add infrastructure for building the loader
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45672
2015-05-11 09:08:33 +00:00
Felix Fietkau
ac0e2479dc mtd: remove the warning about read-only caused by size vs. block boundary mismatch
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.

[    2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[    2.970000] 2 netgear-fw partitions found on MTD device firmware
[    2.970000] 0x000000070000-0x000000188440 : "kernel"
[    2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[    2.990000] 0x000000188440-0x000000ff0000 : "rootfs"

The patch removes the rather useless warning message.

signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

SVN-Revision: 45669
2015-05-10 16:09:58 +00:00
Felix Fietkau
b33752051f ar71xx: add platform_pre_upgrade for sysupgrade
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45667
2015-05-10 13:54:25 +00:00
Felix Fietkau
9ebb99cb98 kernel: fix regression in backtrace module info change (#19631)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45665
2015-05-10 13:16:40 +00:00
Felix Fietkau
cfb56b4811 ipq806x: add pcie support to ipq806x based platforms
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)

We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45663
2015-05-10 11:47:09 +00:00
Felix Fietkau
3c4bc0cd77 ipq806x: add support for zImage kernel
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.

It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45662
2015-05-10 11:47:02 +00:00
Felix Fietkau
bdcba36442 ipq806x: fix boot freeze on zImage kernel
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.

On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.

As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45661
2015-05-10 11:46:56 +00:00
Felix Fietkau
9913b6a90a generic: add CRYPTO_DEV_QCE option to default config
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45658
2015-05-10 11:46:41 +00:00
Luka Perkov
2a9ebfb503 ar71xx: add status led found on ew-dorin boards
Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656
2015-05-10 07:47:04 +00:00
Felix Fietkau
53827cdc82 kernel: when KALLSYMS is disabled, print module address + size for matching backtrace entries
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45655
2015-05-10 00:02:18 +00:00