According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41526
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41515
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41513
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41512
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41511
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.
Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41500
Realview is mostly used as a QEMU development platform, which will provide a
built-in DHCP server to NAT or bridge the connection outside of the emulated
environment.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41495
This is not needed since our toolchain produces the expected binaries for the
target CPU.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41494
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41474
After r41444 wifi working on WRTnode. Tested.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41452
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.
These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41449
The Livebox 1 support is currently broken. Fixed with this patch
Fixes:
- Redboot partitioning broken: fixed
- Replaced custom ephy reset with platform code
- USB code breaks the building process: fixed
- Led colors
- Removed unneded EHCI code since bcm6348 only has OHCI
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: drop unneded parts since merge, fixup to apply to current head]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41424
This adds support for Comtrend WAP-5813n.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41421
Some fixes for Telsey CPVA502+ bcm6348 routers:
- reset the external PHY (eth1) with proper platform code, not using a led definiton
- eth1 is an external phy, not a switch, deleted forced link speed
- fixed led color
Patch made for 3.14 kernel patches.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: also fix 3.14, refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41420
Spotted by several buildbots.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Patchwork: http://patchwork.openwrt.org/patch/5768/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41391
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41346
- Support set VLAN ID of each vlan.
- Support untag feature.
- Replace register address with C MACRO.
- There are 8 ports for MT7530 actually.
Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>
SVN-Revision: 41331
add missing kernelnames to Makefile because those files are needed in 'target/linux/mpc83xx/image/Makefile'. Without them a compilation for mpc83xx is not possible - the buildbot stops with the error "No such file or directory"
Signed-off-by: Claudio Thomas <ct@xmodus-systems.de>
SVN-Revision: 41330
We do not need global access to it, so move it from arch include to the
mtd subdir.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41321
Pass I/O memory regions (flash read and MMR) via platform device
resources array and use them inside spiflash driver.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41320
Moving the start of IO mem to 0x10000000 leads to allocation conflict
with SPI flash memory region, which starts at 0x08000000.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41319
We should not detect actual flash size during board initialization to
find board config at the end of the flash, just use large enough mapping
size (currently 128 mbit). If mapping size is larger than the actual
flash size, than flash will simply be mapped multiple times. This change
simplifies code by removing duplication and saves about 200 bytes of
uncompressed kernel :)
Tested with Ubnt LS2 board equipped with STM 25p32v6p NOR flash (32 mbit).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41317
Merge 3_10-updates.patch into the ar2313_ethernet.patch since it contains
only one ethernet driver fix.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41316
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.
If anyone else is using jffs2_nand on a lantiq target please speak
up!
Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41312
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41310
Use the CFE_EPTSEAL to tell them apart at runtime. Added for now only
for the 3.14 until properly tested.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41296
