This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
These properties allow overriding the settings from the EEPROM
which indicate whether a band is enabled or not.
Setting this property is only needed when the RF circuit does not
support the 2.4GHz or 5GHz band while it is enabled nevertheless in the
EEPROM.
These patches will be replaced with a future upstream version which
will introduces an ieee80211 device tree property to disable bands.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
There are two types of swapping the EEPROM data in the ath9k driver.
Before this series one type of swapping could not be used without the
other.
The first type of swapping looks at the "magic bytes" at the start of
the EEPROM data and performs swab16 on the EEPROM contents if needed.
The second type of swapping is EEPROM format specific and swaps
specific fields within the EEPROM itself (swab16, swab32 - depends on
the EEPROM format).
With this series the second part now looks at the EEPMISC register
inside the EEPROM, which uses a bit to indicate if the EEPROM data
is Big Endian (this is also done by the FreeBSD kernel).
This has a nice advantage: currently there are some out-of-tree hacks
(in OpenWrt and LEDE) where the EEPROM has a Big Endian header on a
Big Endian system (= no swab16 is performed) but the EEPROM itself
indicates that it's data is Little Endian. Until now the out-of-tree
code simply did a swab16 before passing the data to ath9k, so ath9k
first did the swab16 - this also enabled the format specific swapping.
These out-of-tree hacks are still working with the new logic, but it
is recommended to remove them. This implementation is based on a
discussion with Arnd Bergmann who raised concerns about the
robustness and portability of the swapping logic in the original OF
support patch review, see [0].
After a second round of patches (= v1 of this series) neither Arnd
Bergmann nor I were really happy with the complexity of the EEPROM
swapping logic. Based on a discussion (see [1] and [2]) we decided
that ath9k should use a defined format (specifying the endianness
of the data - I went with __le16 and __le32) when accessing the
EEPROM fields. A benefit of this is that we enable the EEPMISC based
swapping logic by default, just like the FreeBSD driver, see [3]. On
the devices which I have tested (see below) ath9k now works without
having to specify the "endian_check" field in ath9k_platform_data (or
a similar logic which could provide this via devicetree) as ath9k now
detects the endianness automatically. Only EEPROMs which are mangled
by some out-of-tree code still need the endian_check flag (or one can
simply remove that mangling from the out-of-tree code).
[0] http://www.spinics.net/lists/linux-wireless/msg152634.html
[1] https://marc.info/?l=linux-wireless&m=147250597503174&w=2
[2] https://marc.info/?l=linux-wireless&m=147254388611344&w=2
[3] 50719b56d9/sys/dev/ath/ath_hal/ah_eeprom_9287.c (L351)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
These patches add support for configuring ath9k based devices via
devicetree. This was tested on PCI(e) based devices. This should work
for AHB based devices as well (adding more AHB specific properties may
still be needed) as soon as the ath79 platform is ready to populate the
ath9k wmac via devicetree.
This patchset was accepted upstream, more information can be found on
the linux-wireless list:
https://www.spinics.net/lists/linux-wireless/msg155474.html
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.
Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The ESP algorithms in CBC mode require echainiv, so have kmod-ipsec
depend on kmod-crypto-echainiv.
See upstream commit 32b6170ca59ccf07d0e394561e54b2cd9726038c.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Our current implementation is pretty old and uses some pre-standard/old
ANSI C style that triggers warnings like:
warning: call to function 'MD5_Init' without a real prototype [-Wunprototyped-calls]
This is caused by declarations specified in a following way:
src/md5.h:60:6: note: 'MD5_Init' was declared here
void MD5_Init ();
Having these warnings makes it harded to notice real problems. We could
try hiding them but it makes more sense to just use a cleaner code.
Another tiny gain from this switch is slightly reduced binary size, on
x86_64 tplink-safeloader's size 48104 became 48003.
The new code is public domain, uses "heavily cut-down BSD license".
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.
Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.
Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.
If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.
Use the usb pinmux settings from the nbg6817 gpl sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).
This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.
Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.
Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.
Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.
Change gpioexport to gpio pinmux.
Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.
Remove pcie pinmux from D7800.
Move pinctrl to correct place in NBG6817 and R7800.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Earlier compilers such as GCC 4 do not like anynomous unions, make it a named
union "u", and update the code where relevant.
Fixes FS#298
Fixes: a72e1692b8 ("firmware-utils: Add support for the Cisco Meraki MX60/MX60W")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fix bug that LEDE failed to boot with this message:
WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).
Signed-off-by: Andrew Yong <me@ndoo.sg>
User-visible changes since 0.64 are as follows:
- Translation fixes
- Project settings have priority
- Reject binary files in patches
- Fix a race condition in diff_file
- Performance: Optimizations to the setup command
- Performance: Optimizations to the bash completion script
- Test suite: Improve the edit test case
- Test suite: Make the symlink test more robust
- Test suite: Test backup failure
- Test suite: Test the header command with hard links
- diff: Report diff failures
- edit: Fix a corner case bug
- mail: Fix the help text
- push: Fix the synopsis
- refresh: Do not remove symlinks
- refresh: Break links to read-only patch files
- refresh: Always preserve modification time
- setup: Report failed look-ups in inspect-wrapper
- quilt.el: Fix quilt-editable when patches are stored in subdirs
- bash_completion: Handle spaces in file names
- bash_completion: Update the list of commands
- bash_completion: Add new command options
- bash_completion: Fix handling of mail, new, push options
- guards: Simplify the help text
- guards: Include the file name also in the "Not found" case
- guards: Add support for an external filelist in --check mode
- guards: Report which config file has problem in --check mode
- guards: Documentation update
- guards: Clarify a user message
Note to packagers: the Makefile was modified to take configure's
--sysconfdir into account as other projects do. As a result, setting
--prefix=/usr will no longer put the configuration files under /etc.
You now need to explicitly pass --sysconfdir=/etc. If you don't,
configuration files will go under /usr/etc, which is not what you want.
This is somewhat less intuitive, but also more consistent with what
other projects are doing.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
RELEASE 2.5.1 - Mon, 03 Nov 2016 13:37:42 -0400
- Add scons-configure-cache.py to packaging. It was omitted
- Use memoization to optimize PATH evaluation across
all dependencies per node.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This device uses NAND FLASH, so it should be kept in nand subtarget.
Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
This constant was always defined to 0, and recently got removed in
upstream commit a07ea4d9941af5a0c6f0be2a71b51ac9c083c5e5 ("genetlink: no
longer support using static family IDs")
Fixes libnl-tiny builds with latest upstream kernels.
Fixes: d723f2573a ("libnl-tiny: remove include/linux overrides to fix various build issues")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
