Bug introduced with 6713694.
I did not count on procd handling reload as mentioned
in this doc:
https://wiki.openwrt.org/inbox/procd-init-scripts
```
procd_set_param file /var/etc/your_service.conf # /etc/init.d/your_service reload will restart the daemon if these files have changed
procd_set_param netdev dev # likewise, except if dev's ifindex changes.
procd_set_param data name=value ... # likewise, except if this data changes.
```
The service would be restarted regardless of any of those params.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
While we have CRASHLOG on MIPS it makes sense to support 'classic'
kexec-based CRASH_DUMP on x86 and arm platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.
The device ist based on a Atheros AR9344 rev 3,
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card
The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)
Running from tftp:
The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
At some point kernel.org decided to drop xz generated tarballs, switch to gz which they still provide.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Use chanreg and dccal helpers to reduce the size of ePA code.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed white-space so patch applies]
I think I added these respawn params [a while back],
when I did the conversion to procd init script format.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This firmware shoul have the same general feature set as the
rest of the 10.4 CT firmware (9984, 9980, etc). Build-tested
only in LEDE, but firmware has been tested with ath10k-ct driver
on other OSs, so likely works just fine.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The 988x and 9887 firmwares include a bugfix for a case where blockack
did not work sometimes, and many fixes for compiler warnings detected
by newer gcc compilers.
The 9980 and 9984 firmware includes a large backport of upstream QCA
firmware changes to bring it up to date.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Supports disabling firmware hex logging that many found too verbose.
Increase BMI timer so system works more often with 9888 Compex NIC
(and maybe others).
Allow configuring a specific board-file per NIC using fwcfg file.
Maybe fix a scan-busy problem when using CT firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Remove support for NCT6775/6 from W83627EHF driver so the NCT6775
driver will still be used for those chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
When in ra server mode, configure nameservers passed in router
announcements from the dns value (which is already used by odhcpd).
This also fixes FS#677 by using the global IPv6 address of the router
instead of the link local address (if no nameservers are configured).
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
We enabled lua interpreter by default as it doesn't make any problem in the uhttpd config file and we modify the index page to use it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This adds support for Aerohive AP-121 access point.
Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:
dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan
This commit adds basic support for Rambutan development kit
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header
Flash instructions:
Stock firmware is OpenWrt, so use:
sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
nand erase.part ubi
nand write 80060000 ubi ${filesize}
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds the build option for the new UniFi AC Mesh.
It is a direct hardware copy from the AC Lite.
- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 1 1000M - POE
- Wireless:
2.4G: QCA9563
5G: UniFi Chip, QCA988X compatible
Thanks to Frank Dietz for testing.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[wrapped too long lines in mach-ubnt-unifiac.c]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add rut5xx GPIO PIN selection to om-package startup script.
Testet on a RUT500 device, the timeout value of the hardware watchdog
is about 280 sec.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
[split into two commits, bump PKG_RELEASE]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This fixes switch port mapping for: TL-WR841N/ND v8, TL-MR3420 v2 and
TL-WR941N/ND v5. All of them share the same Atheros ap123 reference
design.
The order of switch ports (shown in "swconfig dev eth1 show") is CPU,
LAN 4, LAN 1, LAN 2, LAN 3.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[included 2 more devices]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
93abe6f config: fix invalid hoplimit in RA message
2ae08d1 config: fix invalid retranstime in RA message
0005cb4 config: fix invalid reachabletime in RA message
5683dd2 config: limit ra_mtu to 65535
f8d40a5 router: fix interface mtu read error
f8f4b87 config: limit ra_retranstime to 60000
a2d8bf6 dhcpv4: display two hex digits per octet in syslog
a9e9bc4 config: make RA retransTime configurable via uci
2cb6b48 config: make RA reachableTime configurable via uci
e4504db config: make RA curHopLimit configurable via uci
9dd5316 config: make RA mtu configurable via UCI
29cb2ff config: fix dhcpv4 server being started
0ef74ec ndp.c: add switch/case fallthrough comments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
these two devices have a Sata led for each sata port.
These leds must be controlled separately by a special
sata led trigger already used in oxnas target.
Both these devices have a single USB led, and to keep
consistent behaviour with the Sata leds that show
sata activity, this led uses usb-host trigger
to show usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some files (e.g. /etc/dropbear) need to be owned by root. Add cpio
option to ensure that.
Other image types (at least targz and squashfs) already have this.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Gracefully handle cases where the to-be-created wireless interface already
exists on the system which might commonly happen with non-multi-SSID capable
wireless drivers.
This fixes commit 8301e61365 which caused
previously ignored "Too many open files in system (-23)" errors to fail the
wireless setup procedure.
With the updated approach we'll still try recreating the vif after one
second if the first attempt to do so failed with ENFILE but we will now
consider the operation successfull if a second attempt still yields ENFILE
with the requested ifname already existing on the system.
Fixes FS#664, FS#704.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refer to LINUX_KARCH instead of ARCH when bundling DTS files in the image
builder tarball.
While we're at it, also dereference symbolic links when copying as some
kernel architectures contain symbolic links in their DTS directories.
This fixes aarch64 imagebuilders such as brcm2708/bcm2710 ones in particular
as the kernel refers to "aarch64" as "arm64" internally.
Ref: https://forum.lede-project.org/t/lede-image-builder-problem/3680
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Add device tree files for Solidrun ClearFog Base board.
We also need to backport some improvements for Armada
388 MicroSoM.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
The conventional model is now known as the "Clearfog Pro".
We keep the old armada-388-clearfog.dts file for compatibility reasons.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
