This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47849
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47848
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47723
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 230400 Baud.
With this patch Linux will use the configured baud rate and not some
standard one which is near by.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47450
Add access to the function2 gpio register. This probably has to be
converted into a pimux driver later on. This is needed for some setup
functions on the Arduino Yun.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47449
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
The hardware of the v3 is identical to the v2.
Based-on-patch-by: Andreas Ziegler <github@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47406
Some devices require the kernel to be in a JFFS2 file system. Make the
support for this more generic so that it can be used by other devices.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
SVN-Revision: 47404
Incorrect value causes clock inaccuracy as huge as 1/60.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47363
The device is similar to Archer C7 v2, but with 8M of flash, and 6 external
antennas. Reason for breaking the naming pattern is that sticker on the back
mentions "WDR7500" and has no mention of "Archer".
Signed-off-by: Srdjan Rosic <rosic@google.com>
SVN-Revision: 47344
All other tplink images use squashfs+jffs2. I don't see any reason why
this board should use squashfs-only
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47319
Observed on ar71xx/ath79 platforms such as Ubiquiti RouterStations.Reported in #20642.:
(https://dev.openwrt.org/ticket/20642).
If embedded command-line text exists with CONFIG_IMAGE_CMDLINE_HACK=y,firmware
init doesn't initialize environment pointer (fw_init_cmdline not called).
arcs_cmdline is not initialized before calling strlcat.
Signed-off-by: Ted Hess <thess@kitschensync.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47270
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47263
ath9k expects to get revision id 2 for the QCA9531 ver. 2 rev. 0. This
fixes the very low TX power on some devices like the TP-LINK
TL-WR841ND v10.
As ath79_soc_rev is only used to get the revision number to ath9k on the
QCA9533, just set it to the expected value on the ver. 2.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47262
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47261
