TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)
QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.
Flash instruction:
Use "factory" image directly in vendor GUI.
Recovery method:
1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server.
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset
This commit is based on GitHub PR#1112
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan
This commit adds basic support for Rambutan development kit
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header
Flash instructions:
Stock firmware is OpenWrt, so use:
sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
nand erase.part ubi
nand write 80060000 ubi ${filesize}
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).
All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).
The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB
TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")
Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.
Signed-off-by: P.Wassi <p.wassi at gmx.at>
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
move all library includes and 'firmware already exists'
check to the top of the script.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47947
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
SVN-Revision: 46415
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
- move WiFi MAC address setup to the firmware hotplug file,
- use the official MAC address for the 2.4GHz as well,
- remove uci-defaults.sh modifications,
- update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38812
