Commit graph

17776 commits

Author SHA1 Message Date
Piotr Dymacz
4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Ryan Mounce
978998628f ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).

All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Ryan Mounce
540edf7045 ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).

The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
John Crispin
dce3b0057b ramips: fix mt7621 boot on v4.9
v4.9 CM code has a few bugs on this HW. Disable the GCR register access
during boot. This caused a cpu stall.

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-23 09:18:42 +01:00
John Crispin
666bfc6fb5 Revert "ipq806x: make the dwc3 driver and required phy drivers built-in"
This reverts commit d5b10bb560.

This caused boot errors on some ipq8 boards

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-23 08:29:44 +01:00
Rafał Miłecki
cfc5b35dd4 kernel: disable DRM_HISI_KIRIN and USB_DWC3_OF_SIMPLE
They were triggering config prompts on brcm2710.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-22 14:22:35 +01:00
Rafał Miłecki
bf381f8f63 kernel: fix builds with kmod-drm-vc4 and CONFIG_SPI enabled
This fixes:
Samsung LD9040 RGB/SPI panel (DRM_PANEL_SAMSUNG_LD9040) [N/m] (NEW) aborted!

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-22 12:22:33 +01:00
Felix Fietkau
9b940fe80d x86: enable ACPI support for the Geode subtarget
Most or all newer Geode device have ACPI hardware support
Should fix FS#577

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:51:24 +01:00
Felix Fietkau
ca44b9a0d4 pistachio: remove custom board detection override
Use device tree based model string

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Felix Fietkau
c0e8108b70 pistachio: fix indentation in image makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Felix Fietkau
eb98bf605e pistachio: remove pistachio_board_name, use the generic function
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Ian Pozella
0d271cef80 target: add pistachio
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.

This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.

Note, this commit is just the initial board support hence the
following are not expected to work yet:
 * WiFi
 * Bluetooth
 * 6lowpan
 * Audio
 * Mikrobus uarts, user leds (clock dependency of 6lowpan chip)

The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.

Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
2017-03-22 11:43:22 +01:00
Ian Pozella
52c17bff3c pistachio: add 4.9 kernel support
This adds kernel support for the Pistachio SoC and the Marduk (Ci40)
board which uses it.

Much of the code for Pistachio has been upstreamed however some
patches are still required to boot from the Marduk board:
 * spi bug fixes
 * dma bug fixes
 * pistachio internal clock tree bug fixes
 * spi-nand implementation
 * dts based mtd device naming scheme
 * dts backports and bug fixes

Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
2017-03-22 11:43:22 +01:00
Felix Fietkau
fd93f81fd8 lantiq: remove lantiq_board_model, it is unused
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Felix Fietkau
7e798dab56 lantiq: remove lantiq_board_name, use the generic function instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:21 +01:00
Felix Fietkau
aa95d6cd20 lantiq: move lantiq_board_detect() to 03_preinit_board.sh
It is only used there

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:21 +01:00
John Crispin
3a3564ead5 ipq806x: remove v4.4 support
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
John Crispin
ef6c4cc4ee ipq806x: set v4.9 as default
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
John Crispin
d5b10bb560 ipq806x: make the dwc3 driver and required phy drivers built-in
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
John Crispin
7dc5617173 ipq806x: enable QCE hardware crypto inside the kernel
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Christian Lamparter
1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Christian Lamparter
c2d50bdeb3 ipq806x: add ipq4019 support
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Rafał Miłecki
61eeb21545 kernel: fix builds with kmod-drm-vc4 and kmod-backlight enabled
This fixes:
JDI LT070ME05000 WUXGA DSI panel (DRM_PANEL_JDI_LT070ME05000) [N/m/?] (NEW) aborted!

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-22 08:49:33 +01:00
Rafał Miłecki
fbf89732c4 brcm2708: add kmod-drm-vc4 package
It includes vc4 driver for Broadcom VideoCore IV GPU.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-21 23:44:24 +01:00
Rafał Miłecki
8fae77fc9b kernel: update bcma including recent changes for 4.12
This adds support for describing GPIO chips placed on PCIe cards. Thanks
to this we get working 2.4 GHz LED on Tenda AC9.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-21 09:58:05 +01:00
Rafał Miłecki
e41e1e6a2a kernel: move disabling DRM symbols to the config file
This is the standard way we handle this. Please note (it seems) I could
drop few symbols as they are hidden under (disabled) DRM_LEGACY now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-21 08:22:56 +01:00
Rafał Miłecki
b4d5132a35 kernel: disable CONFIG_BCM_IPROC_ADC by default
This fixes compiling issue on bcm53xx target with kmod-iio-core:
Broadcom IPROC ADC driver (BCM_IPROC_ADC) [N/m/?] (NEW)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-21 07:16:42 +01:00
Furong Xu
2fd1a3e912 ramips: clean kernel config symbol conflicts for MT7688 PWM
pwm-mediatek should be selected in Other Modules submenu, not default to yes.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-20 08:17:34 +01:00
Vaclav Svoboda
6b9c25e927 ramips: fix switch port mapping for ZBT-WE2026
This patch fixes switch port mapping for Zbtlink ZBT-WE2026.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-20 08:13:56 +01:00
Hannu Nyman
3f9eadf599 ipq806x: support independent core clocks in cpufreq with kernel 4.9+
Add back support for the independent_clocks definition that has been
removed between kernel 4.4 and 4.9 by upstream commits
eb96924acddc709db58221c210ca05cd9effb1df and
e86eee6bc2aaa6b3637f6497b26beee09a91bde9

* extend the new cpufreq_dt_platform_data definition in cpufreq-dt.h
* revert the removal of its usage in cpufreq-dt.c
* use new cpufreq-dt.h in qcom-cpufreq.c

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2017-03-20 08:12:49 +01:00
Pavel Kubelun
ef4ca01d6f ipq806x: route gpio interrupts to APPS processor through scm firmware
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-03-20 08:11:29 +01:00
Pavel Kubelun
0d89650db1 ipq806x: remove scm firmware clocks
At the moment as a workaround definition for scm firmware in DT is used as if it is
apq8064 board. This leads to incomplete scm firmware initialization and as a result
cpuidle driver fails to configure.

By design unlike other qcom boards ipq do not use clocks to connect to scm.

Considering this we're removing from DT and scm driver clocks for ipq boards.

As a result cpuidle does not produce errors about failed configuration anymore.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-03-20 08:11:29 +01:00
Rafał Miłecki
0694d08c84 bcm53xx: switch to kernel 4.9
With iproc regression fixed and GIC interrupts in DTS updated it seems
we can safely start using 4.9.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-18 23:00:56 +01:00
Rafał Miłecki
3a2e735b96 bcm53xx: backport BCM5301X patches
This fixes GIC interrupts (required before switching to 4.9), adds few
new entires & introduces DTS for Archer C5.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-18 18:32:53 +01:00
Oswald Buddenhagen
6a82f4006c lantiq: Shortcut non-pppoa interfaces in dsl_notify
No need to query 'up' and 'auto' when they are not going to be used.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
2017-03-17 08:58:50 +01:00
Vaclav Svoboda
815cc2a69a ramips: add support for Zbtlink ZBT-WE2026
This patch adds support for the Zbtlink ZBT-WE2026.

Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M

Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-17 08:58:50 +01:00
Stefan Koch
443e67a459 lantiq: vr9 fxs support: fixed check of SMP state within vpe-mt.c
SMP state is generally affected by
- CONFIG_SMP build-time kernel configuration option and
- 'nosmp' runtime kernel commandline option

The SMP state within vpe-mt.c is determined by CONFIG_SMP option.
A runtime check is needed if VPE functionality
should be used with a kernel image that supports SMP.

This fix introduces a check for 'nosmp' command line option
if CONFIG_SMP kernel configuration option is enabled.

Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP
(that activates CONFIG_SMP) is enabled within kernel configuration
and the 'nosmp' command line argument is given to disable SMP at runtime.

Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS.
With this patch setting the 'nosmp' parameter is enough.

In general, concurrent usage of FXS and SMP
is incompatible and will cause kernel panics.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2017-03-17 08:58:50 +01:00
Felix Fietkau
afc1675833 kernel: do not build modules.order
It is not needed for anything on the system and skipping this saves some
build time, especially in cases where there is nothing to do.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-16 19:14:24 +01:00
Felix Fietkau
6bada71e51 kernel: add missing config symbols for 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-16 11:29:03 +01:00
Jing Qiu
4475da968a kernel: Fix the incorrect i_nlink count after jffs2's RENAME_EXCHANGE operations.
The problem is caused by the incorrect handling of the parent inode's
i_nlink count for the dentry to be RENAME_EXCHANGED. There are 3 cases
to consider. Assume we want to RENAME_EXCHANGE struct dentry *a and
struct dentry *b, and inode_a is pointed to by dentry_a, inode_b is
pointed to by dentry_b:

1. If inode_a is a directory, but inode_b isn't, then we must decrease
   the i_nlink count of old_dir_i, and increase the i_nlink of new_dir_i.
2. If inode_a isn't a directory, but inode_b is a directory, then we
   must increase the i_nlink of old_dir_i, and decrease the i_nlink count
   of new_dir_i.
3. If the types of inode_a and inode_b are the same, we don't change the
   i_nlink for either old_dir_i or new_dir_i.

Signed-off-by: Jing Qiu <aqiu0720@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-16 11:28:40 +01:00
Rafał Miłecki
425f958830 x86: image: drop duplicated copy of bzImage into vmlinuz
It's already done once few lines earlier in the Image/Build/iso.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-16 11:28:33 +01:00
Piotr Dymacz
f9a1f322d2 brcm63xx: diag.sh: use common status_led_blink_* functions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:15:19 +01:00
Piotr Dymacz
5cc96c0953 ar7: diag.sh: use common status_led_* functions
Switch to the common LED related status_led_blink_* functions in
set_state() as it's done in most of other targets.

Also, use "status_led_on" instead of "status_led_set_heartbeat"
and incorrect "status_led_set_on" in the "done" state.

Moreover, remove outdated comment from the script.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:14:54 +01:00
Thibaut VARENE
e1f3cf7ede ar71xx: mikrotik: prepend "RouterBOARD" to machine name for NOR devices
When the device name doesn't already contain "RouterBOARD", this patch adds
this string to the machine name.

Most NOR devices already have "RouterBOARD" in their hardware-stored device name,
but not all of them.

This patch also makes the code more robust against buffer overflows.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Thibaut VARENE
e3dc036cbf ar71xx: add support for RB LHG 5nD
This patch adds support for the MikroTik RouterBOARD LHG 5
https://routerboard.com/RBLHG-5nD

Specifications:
- SoC: Atheros AR9344 (600MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin AR9344 5GHz, 2x2:2
- Ethernet: 1x100M

Initial flash via initramfs, like all other RB devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Michael Marley
51130b9927 kernel: Add intel_idle driver to x86_64 build
This driver supports CPU-specific idle features on recent Intel
processors.  It does not conflict with the ACPI idle driver and
that driver will continue to be used for unsupported and non-Intel
processors.

Signed-off-by: Michael Marley <michael@michaelmarley.com>
2017-03-14 13:28:04 +01:00
Michael Marley
39df43b9e5 kernel: Add coretemp driver to x86_64 build
The x86_64 build already has the k10temp driver for AMD processors
built in, so this patch adds the coretemp driver for the same
functionality on Intel processors.

Signed-off-by: Michael Marley <michael@michaelmarley.com>
2017-03-14 13:28:04 +01:00
Felix Fietkau
772ec02a46 kernel: add missing config symbols for 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-14 13:28:04 +01:00
Felix Fietkau
894ee9510b ipq806x: fix ethernet DMA parameters with linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 21:42:47 +01:00
Felix Fietkau
7ffaf71d53 ipq806x: fix pcie with linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 21:10:31 +01:00
Stefan Koch
d4203dfa55 lantiq: vr9 fxs support: fixed check of SMP state within vpe-mt.c
SMP state is generally affected by
- CONFIG_SMP build-time kernel configuration option and
- 'nosmp' runtime kernel commandline option

The SMP state within vpe-mt.c is determined by CONFIG_SMP option.
A runtime check is needed if VPE functionality
should be used with a kernel image that supports SMP.

This fix introduces a check for 'nosmp' command line option
if CONFIG_SMP kernel configuration option is enabled.

Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP
(that activates CONFIG_SMP) is enabled within kernel configuration
and the 'nosmp' command line argument is given to disable SMP at runtime.

Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS.
With this patch setting the 'nosmp' parameter is enough.

In general, concurrent usage of FXS and SMP
is incompatible and will cause kernel panics.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2017-03-13 14:20:47 +01:00
Felix Fietkau
5267ff2b6a ipq806x: re-enable the RAM clock for gcc on 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:57 +01:00
Felix Fietkau
2029167b56 ipq806x: fix crash on 4.9 if the rpm clock probe happens before cpuidle init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:56 +01:00
Felix Fietkau
2a4baf3e79 ipq806x: fix NAND support for linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:56 +01:00
Felix Fietkau
6006227cb7 ipq806x: do not allocate coherent memory in dma engine hotpath
The available amount of coherent DMA memory is very limited. On Linux
4.4 this issue was worked around by increasing the pool size.

It turns out that using coherent memory here is completely unnecessary.
This change reworks the driver code to use kzalloc+dma_map_single
instead.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:56 +01:00
John Crispin
1adf51702e ipq806x: clean up patches, port missing patches from 4.4
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:55 +01:00
John Crispin
99b6aefd63 ipq806x: sync 4.9 kernel config with 4.4
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:40:46 +01:00
Felix Fietkau
a531d37fab ipq806x: clean up dts patching in 4.9
Do not patch upstream files, overwrite them entirely. The upstream files
are buggy for a number of devices and this significantly simplifies the
patch structure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:33:51 +01:00
Felix Fietkau
ddf577b0b2 ipq806x: enable cmdline mangle on 4.9 (like on 4.4)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:33:50 +01:00
Daniel Gonzalez Cabanelas
080c6fa476 ar71xx: WNDR4300: Fix network vlan IDs
The Netgear WNDR4300 has the VLAN IDs flipped in LuCi, fix it.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-03-13 00:13:18 +01:00
Daniel Gonzalez Cabanelas
ad9ad376bb ar71xx: WNDR4300: Fix switch HW controlled LEDs
The Netgear WNDR4300, equipped with an Atheros AR8327 Gigabit Switch,
has two LEDs on each port for monitoring LAN activity, but it currently
only uses one. Fix the configuration to use both.

The patch provides this new configuration:
- green LED: 1 Gbps link, 4Hz blink frequency
- amber LED: 10/100 Mbps link. 4Hz for 100Mbps, 2Hz for 10Mbps

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-03-13 00:12:07 +01:00
Piotr Dymacz
09862bb006 ar71xx: fix Wallys DR344 ethernet MAC addresses offsets
Without this fix, ethernet interfaces on Wallys DR344 use random MAC
addresses.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:52:19 +01:00
Piotr Dymacz
7e38ce2e7d ar71xx: base-files: few minor cleanups in lib/ar71xx.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:47:59 +01:00
Piotr Dymacz
c2b5206c80 ar71xx: base-files: fix boards order in lib/ar71xx.sh
Keep everything within case statements in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:47:59 +01:00
Piotr Dymacz
d9bc3e6882 ar71xx: base-files: shorten case statement patterns in lib/ar71xx.sh
At now there is no general rule about what part of (or whole) machine
name string should be used for board name assignment/detection and every
target handles this in a different way.

For most of the boards in ar71xx we already use only part of the string,
generally without the vendor name.

This shortens wildcards patterns in case statement for board name
assignment, wherever possible (e.g. where it won't be misleading).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:47:59 +01:00
Piotr Dymacz
4f09837cdf ar71xx: base-files: always use double quotes in lib/ar71xx.sh
Be consistent and always use double quotes for case statement patterns,
as in other targets. With this approach it should be less confusing for
users adding support for new devices.

Also, be consistent with MikroTik boards wildcard pattern.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 23:43:17 +01:00
Piotr Dymacz
589b37e8b5 ar71xx: base-files: fix indentation in lib/ar71xx.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 17:39:12 +01:00
Piotr Dymacz
e213647399 ar71xx: fix machine name for several devices
Be consistent with form and format of the vendor name.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-12 17:39:12 +01:00
Shuanglin Liu
53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Rafał Miłecki
cd0f9900a4 bcm53xx: parepare for building more Linksys images
We still can't enable them by default without proper TRX support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-12 16:24:13 +01:00
Hauke Mehrtens
31c6452107 kernel: update kernel 4.4 to 4.4.53
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-12 15:46:02 +01:00
Hauke Mehrtens
9a065fcfec kernel: update kernel 4.9 to 4.9.14
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-12 15:45:50 +01:00
Rafał Miłecki
f5d403488e x86: image: drop unneeded grub call
It appears there isn't any Image/Build/grub/* define so this step looks
redundant.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-12 15:06:52 +01:00
Rafał Miłecki
9a267e6a4b x86: image: drop unused ROOTDELAY variable
It's unused since commit 7427007193 ("x86: remove the olpc subtarget,
it has been unmaintained for a long time").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-12 15:06:52 +01:00
Tim Harvey
b2255f3621 imx6: add DSA driver for MV88E6176 switch
The MV88E6176 switch is present on the GW16083 and the GW5904

As of a5c32a1f19 these drivers are to be
enabled static in per-target kernels.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-12 15:06:52 +01:00
Tim Harvey
5f458bf7f8 imx6: add support for GW5904
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-12 15:06:51 +01:00
Tim Harvey
35d761c0c5 imx6: added fixfdt to bootscript
If a 'fixfdt' uboot script exists, execute it prior to bootm to allow
easy bootloader env based fdt fixups and tweaks

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-12 15:06:51 +01:00
Tim Harvey
028350907e imx6: add missing dtb for imx6dl-gw553x
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-12 15:06:51 +01:00
Tim Harvey
4cc70d8610 imx6: fix USB for 4.9 kernel
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-12 15:06:50 +01:00
Tim Harvey
08371a2db7 kernel: fix phy aneg crash
Fix a kernel crash caused when CONFIG_FIXED_PHY used for fixed phy drivers
in phy-add-aneg-done-function patch.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-12 11:58:45 +01:00
Mathias Kresin
11eac705c5 ramips: sort mt7620 image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-12 09:28:19 +01:00
Joseph C. Lehner
de33a4cef0 ramips: add support for Netgear EX3700
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the device's web
interface or via nmrpflash.

Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Hanqing Wong
38bee61dab ramips: add support for Netgear R6220
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.

Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
  on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
  (login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
  example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Signed-off-by: Hanqing Wong <hquu@outlook.com>
2017-03-12 09:28:05 +01:00
Henryk Heisig
6674aa9798 mvebu: wrt3200acm enable SDIO interface
add mwifiex-sdio package to wrt3200acm

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-03-11 14:16:28 +01:00
Mathias Kresin
73eb5c74a1 lantiq: use the P2812HNUF* wan port as wan
The port is labeled as wan and was only used as lan port because of the
"tx ring full" issues fixed with 8f02f7c.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-11 13:45:06 +01:00
Mathias Kresin
cd8b20931e lantiq: xrx200: use vlan for ethernet wan port
Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.

The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.

If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.

Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-11 13:45:00 +01:00
Mathias Kresin
715b066419 lantiq: fix broadcasts and vlans in two iface mode
The two phy operation mode where one phy is assigned to an interface
without lantiq,* device tree property and the other phy is assigned to
an interface with the lantiq,wan device property was broken with the
multicast package leaks between vlans fixes.

Move the multicast packages relevant portmap settings to the condition
which handles multicast packages for better readability.

Replace the priv->port_map based port_map only for the interface which
has the lantiq,switch device tree property set, to allow tagged
multicast packages in two phy mode where the lantiq,switch device tree
property isn't used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-11 13:45:00 +01:00
Rafał Miłecki
cc3c50eb22 bcm53xx: prepare for building Archer C5 V2 image
Don't enable it yet as kernel needs to be updated first.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-11 12:33:53 +01:00
Kristian Evensen
b11c51916c ramips: Improve Sanlinking D240 config
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.

* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.

v2->v3:
* Indentation error.

v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-03-11 08:36:52 +01:00
Stijn Segers
0ad82375cd ar71xx: add ath10k driver and firmware for Netgear R6100 to firmware image
A Netgear R6100 owner reported the LEDE images lack the ath10k driver and firmware [1]. This patch adds both to the R6100 image.

[1] https://forum.lede-project.org/t/netgear-r6100-5ghz-wifi-not-working-after-initial-install/2222

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2017-03-11 08:30:56 +01:00
John Crispin
99d0633f24 kernel: add another missing TPM symbol
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-11 08:27:10 +01:00
Furong Xu
a93a48328d ramips: kmod-sdhci-mt7620: switch dependence to kmod-mmc
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-11 08:19:37 +01:00
John Crispin
0e56151ab2 mediatek: fix ESW EINT pinctrl define
This got lost while bumping the target to v4.9 causing ethernet issues on
some boards.

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-11 07:49:58 +01:00
Rafał Miłecki
e58ea0a80d bcm53xx: use upstream fix for iproc regression
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-10 22:26:20 +01:00
Rafał Miłecki
edda26dc4f bcm53xx: fix memory corruption caused by iproc PCE controller driver
This is a simple revert of upstream patch for now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-03-09 11:06:55 +01:00
Ansuel Smith
2261c9cc77 mvebu: add default sata trigger
Change dts file to add default sata trigger to sata led.

Backport upstream accepted patch to add sata trigger to device tree
source files already upstreamed.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[backport upstream accepted patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-08 19:06:04 +01:00
Ansuel Smith
3d0bd15056 mvebu: enable disk led trigger
As we have a disk led we enable the disk trigger that work with the easata port

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2017-03-08 19:06:04 +01:00
Alex Maclean
6254a2028c lantiq: add support for the Alpha ASL56026
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.

CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04

UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX

Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.

The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)

To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:

	VR9 # setenv loadaddr 0xB0040000
	VR9 # setenv f_upgrade_addr 0xB0040000
	VR9 # setenv f_upgrade2_addr 0xB0040000
	VR9 # saveenv

Then flash the firmware image:

	VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
	VR9 # erase B0040000 +${filesize}
	VR9 # cp.b 0x81000000 0xB0040000 ${filesize}

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-03-08 19:06:04 +01:00
Alex Maclean
a9b74f9f81 lantiq: clarify VG3503J name
Append the ECI model to the device name, to avoid confusion with the
older model.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-03-08 19:06:04 +01:00