This breaks some devices where the serial console is not at port 0 but
somewhere else.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39060
The wait instruction is only broken on the BCM4706 and not on the other
similar SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38979
This sets both values to the OpenWrt default values. There is no reason
to use some brcm47xx specific values here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38978
This adds support for vectored interrupts in this SoC.
This is supported by the 74K cpus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38975
bcm47xx misses cpu overwrites for the features of the CPUs used in
these SoCs.
Instead of manually checking, it is now known at compile time for some
options and the compiler is able to remove the checks and optimize the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38974
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:
commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat Apr 6 22:22:26 2013 +0000
brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.
This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
Some devices are using tty1 as the default console, also swap the early
boot console in such case. This is needed for the WGT634U.
Thank you Russell for reporting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38794
boardnum is unstable, so allow using NULL to make it unchecked.
A method for differentiating F7D3301 from F7D3302 using nvram is
unknown at this point. Reading the first 32bits of magic from the
"linux" mtd partition would do the trick, but these 2 are similar
enough that we don't need separate led/button definitions. Not knowing
which one you have is only a usability issue for upgrading the device:
they expect different magic numbers for their trx images.
Signed-off-by: Cody P Schafer <devel@codyps.com>
SVN-Revision: 38767
It is a problem when phydev is not set at this position and not the other way around.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38744
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38699
When the mdio bus is unregistered the newly created phy will also be
unregistered and freed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38539
On some devices with e.g. a BCM2535F switch the second MAC is used, but
we can not find a phy under all addresses between 0 and 31, 0xffffffff
is returned as phy id. If we can not find a phy at the expected address
create a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38538
Without this patch we treated only phy addr 30 as an external phy, but
there is a register to check that. Now we do not have to try to reset
the switch to check for an external switch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38502
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
SVN-Revision: 38312
Early printk was disabled because it caused hangs on some devices, the
old patches were using the CFE console now we use the normal serial
console, it is at a constant address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38309
Add patches like they are currently in the mainline mips tree and add
some more pending patches for board detection.
* Now the board name is shown under machine in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38308
* do not try initialize a unused phy
* some improvements to the phylib patch
* do not turn the phy off when mac is off
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38306
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38294
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
These are only the patches already applied in current net-next/master
branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38288
This adds support for Byte Queue Limits in bgmac and b44, now it is
possible to use more advanced network queue control algorithms.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38038
This updates the patches for BCM5354 to the version send for upstream
Linux inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38037
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38036
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 38011
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38005
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38004
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001
