Commit graph

20109 commits

Author SHA1 Message Date
Chuanhong Guo
a44f000077 ramips: mt7621-spi: replace the driver with upstream staging one
That driver is more efficient thanks to the refactor of spi reading operation.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-11-26 12:24:30 +01:00
Pawel Dembicki
20b09a2125 ramips: add support for Lava LR-25G001
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN)
- 2x external, detachable antennas
- 1x USB 2.0
- UART (J3) header on PCB (57600 8n1)
- 8x LED (3x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- Work only three Gigabit ports (3/5, 1 WAN and 2LAN)

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Pawel Dembicki
b85fe43ec8 ramips: mt7620: add force use of mdio-mode
Some boards have external switches different than mt7530.

This patch allow to use mdio-mode without 0x1f register.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Pawel Dembicki
e61812fd34 ar8216: add adjust_link checking
Driver crash when 'phydev->adjust_link' isn't provided.

This patch check if 'phydev->adjust_link' exist before
call the method.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Weijie Gao
ed25e3ac02 ramips: fix some clocks in mt7621.dtsi
As the cpu clock calculation has been fixed, the clock for gic and spi
should be also fixed.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
c7ca224299 ramips: fix cpu clock of mt7621 and add dt clk devices
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.

This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
f5af8be636 ramips: fix register range of memc node in mt7621.dtsi
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
e217d69a4a ramips: merge two patches 101-mt7621-timer and 998-mt7621-needs-jiffies
These two patches both modified the mt7621.c, and the patch file
998-mt7621-needs-jiffies.patch adds only one line which is used by the
another patch file. So merge them into one file.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
INAGAKI Hiroshi
83f08aebb1 ath79: specify "firmware" partition format for Buffalo devices
Specify firmware partition format (denx,uimage) by compatible string
for Buffalo devices.

affected devices (&run tested):
- BHR-4GRV
- WHR-G301N
- WZR-HP-AG300H
- WZR-HP-G302H A1A0
- WZR-HP-G450H (WZR-450HP)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:09:25 +01:00
Tomasz Maciej Nowak
d93b09fa74 sdk: expose part of advanced configuration options
These option can be useful in developement/packagig applications for
OpenWrt. Instead of searching them by hand in Config-build.in lets
expose them for easier access.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:07:06 +01:00
Lorenzo Bianconi
e612e60517 ramips: add mt76x0 node to RT-AC51U device tree
Introduce mt76x0e device tree node in RT-AC51U dts.
Define mt76x0e mtd partition and offset

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
2018-11-26 12:05:47 +01:00
Christian Lamparter
5d5c0b0582 apm821xx: wndr4700: restore sd-card media detection
This was not converted to the new, dt-based board name.

Fixes: e90dc8d272 ("apm821xx: convert to device-tree board detection")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:47 +01:00
Christian Lamparter
a2266a6d42 apm821xx: shuffle helper scripts to the front
In a patch for the ath79, Mathias Kresin mentioned that
helper scripts should be in front of the device targets.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:47 +01:00
Christian Lamparter
d82d84694e apm821xx: add support for the Netgear WNDAP620 and WNDAP660
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.

Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM:  128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes

Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM:  256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes

Flashing requirements:

 - needs a tftp server at 192.168.1.10/serverip.
 - special 8P8C(aka RJ45)<->D-SUB9 Console Cable
   ("Cisco Console Cable"). Note: Both WNDAP6x0 have
   a MAX3232 transceivers, hence no need for any separate
   CMOS/TTL level shifters.

External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
 = Config# = | = GPIO 11 = | = GPIO 14 = |  ===== Description =====
      1.     |   1 / High  |  0 / Low    | Use the internal antennae (default)
      2.     |   0 / Low   |  1 / High   | Use the external antennae

The external antennaes are only meant for the 2.4 GHz band.

One-way Flashing instructions via u-boot:

 0. connect the serial cable to the RJ45 Console Port
    Note: This requires a poper RS232 and not a TTL/USB adaptor.

 1. power up the AP and interrupt the u-boot process at

    'Hit any key to stop autoboot'

 2. setup serverip and ipaddr env settings
    Enter the following commands into the u-boot shell
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.10

 3. download the factory.img image to the AP
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img

 4. verfiy image integrity
    Enter the following commands into the u-boot shell

    # crc32 $fileaddr $filesize

    If the calculated crc32 checksum does not match, go back to step 3.

 5. flash the image
    Enter the following commands into the u-boot shell

    # nand erase 0x110000 0x1bd0000
    # nand write ${kernel_addr_r} 0x110000 ${filesize}

 6. setup uboot environment
    Enter the following commands into the u-boot shell

    # setenv bootargs
    # setenv fileaddr
    # setenv filesize
    # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
    # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
    # setenv bootcmd 'run owrt_boot'
    # saveenv

 7. boot
    # run bootcmd

Booting initramfs instructions via u-boot:

 Follow steps 0 - 2 from above.

 3. boot initramfs
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
    # run addtty
    # bootm ${kernel_addr_r}

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
a9839fe638 generic: rtl8367b: make it possible to specify cpu_port via DT
This patch adds the feature to parse the existing cpu_port DT
property, which is used to specify which port is the cpu port
of the switch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
910c2f9e68 generic: rtl836x: support defered probe on mdio-bus
On the WNDAP620, the mdio and mdc lines are controlled by
the EMAC ethernet device. This results in a hen-vs-egg problem.
The rtl8367b driver is probed before the ethernet driver and
the mdio-bus is not available yet, which caused the rtl8367b
driver to fail.

This patch changes the rtl8366_smi_probe_of() function to
return -EPROBE_DEFER if the mdio-bus lookup failed and changes
rtl8366_smi_probe()'s signature to return the error code back to
the callee, so it can propagate back to the kernel. Which, will
retry the switch probe at a later time.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
fb4bed5fe9 apm821xx: import gpio-export DT code from lantiq
This will come in handy for the Netgear WNDAP620's antennae mux.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
f6968952df apm821xx: MR24: add to uboot-envtools
This patch adds the complicated u-boot
environment access settings for to the
MR24 target.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Ram Chandra Jangir
dc6af37544 ipq806x: Add support for IPQ8064 AP161 board
Specification:
   - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
   - RAM: 512MB DDR3 System Memory
   - NOR Flash: 32MB SPI NOR
   - NAND Flash: 256MB NAND
   - Ethernet: 5 x 1G via QCA8337N
   - USB: 2 x USB 3.0 SuperSpeed
   - PCIe: 3x Mini PCIe 2.0 Slots
	   Three PCIE2.0 connectors can connect two or three radio cards
           such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN

 How to flash via u-boot console:
   tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
   nand erase  0x1340000 0x4000000
   nand write  0x44000000 0x1340000 $filesize
   setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
   saveenv
   bootm

 Further upgrades via sysupgrade.

 Tested on IPQ8064 AP161 Board:
   1) NAND boot
   2) Tested USB and PCIe interfaces
   3) WDOG test
   4) cpu frequency scaling
   5) ethernet, 2G and 5G WiFi
   6) ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-11-26 12:05:46 +01:00
Ram Chandra Jangir
1ade96def7 ipq8064: pinctrl: Fixed missing RGMII pincontrol definitions
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-11-26 12:05:46 +01:00
Sergey Ryazanov
8baad26d01 ar71xx: fix RouterBOARD Power LED default state
RouterBOARD(s) bootloader actully turns Power LED off just before
it starts the kernel. So we need to set the LED default status to On
instead of Keep in order to keep LED on during kernel boot.

This change fixes Power LED off during the kernel boot on the RB91x and
SXT Lite boards.

Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state")

CC: Mathias Kresin <dev@kresin.me>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-11-26 12:05:45 +01:00
Ben Greear
38167cb7f4 hotplug: Allow configuring radio name.
This way the radio (phy) name can be the same through module reloads.

To set the desired name:

uci set wireless.@wifi-device[0].phyname=wiphy0

I guess this only works on ipq6086 boards as I could not find a more
generic place to put this.  Maybe someone can improve it.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-11-26 12:05:45 +01:00
Tomasz Maciej Nowak
a822283c7e x86: add amd microcode entries to grub config
Create initrd enries for x86 images, that'll load amd microcode as early
as possible. Also remove the preinit script responsible for late load of
microcode.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:45 +01:00
David Bauer
946ffe470d ath79: add support for Archer C58/C59 v1
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.

CPU:   Qualcomm QCA9561
RAM:   64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi:  QCA9561 bgn 3x3:3
       QCA9888 nac 2x2:2
LED:   Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
       Only C59: USB
BTN:   WPS, WiFi, Reset

Installation
------------

Via Web-UI:
Update factory image via Web-UI.

Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.

Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 12:05:45 +01:00
Daniel Santos
89eb1a6d72 ralink: Add support for GPIO as interrupt-controller
The gpio-ralink driver has everything it needs to be used as an
interrupt controller except for device tree support.  This simple patch
adds that support by configuring the irq domain to use two cells and
adding the appropriate documentation to the devicetree bindings.

Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
2018-11-26 12:05:45 +01:00
Luo chongjun
9989fd5154 ath79: add support for GL-iNet GL-X750
this patch adds supports for GL-X750.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)

Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-11-26 12:05:45 +01:00
Christoph Krapp
987b961537 ar71xx: add support for UniFi-AC-Mesh-Pro
This adds the build option for UniFi AC Mesh Pro as well as
model detection for it.
The device is a hardware clone of the AC Pro.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 2x 1000M - POE+
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-11-26 12:05:44 +01:00
Petr Štetiar
16b950c981 ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.

Specifications:

- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)

Flashing instructions:

A) The U-Boot has HTTP based firmware upgrade

  A1) Flashing notes

  We've identified so far two different batches of units, unfortunately
  each batch has different U-Boot bootloader flashed with different
  default environment variables, thus each batch has different IP address
  for accessing web based firmware updater.

  * First batch has web based bootloader IP address 1.1.1.1
  * Second batch has web based bootloader IP address 192.168.1.250

  In case you can't connect to either of those IPs, you can try to get
  the default IP address via two methods:

  A1.1) Serial console, then the IP address is visible during the boot

   ...
   HTTP server is starting at IP: 1.1.1.1
   raspi_read: from:40004 len:6
   HTTP server is ready!
   ...

  A1.2) Over telnet/SSH using this command:

   root@bdcom:/# grep ipaddr= /dev/mtd0
   ipaddr=1.1.1.1

  A2) Flashing with browser

  * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
  * Reboot the device and try to reach web based bootloader in the
    browser with the following URL http://1.1.1.1

  * Quickly select the firmware sysupgrade file and click on the
    `Update firmware` button, this all has to be done within 10 seconds,
    bootloader doesn't wait any longer

   If done correctly, the web page should show UPDATE IN PROGRESS page
   with progress indicator. Once the flashing completes (it takes roughly
   around 1 minute), the device will reboot to the OpenWrt firmware

  A3) Flashing with curl

   sudo ip addr add 1.1.1.2/24 dev eth0
   curl \
      --verbose \
      --retry 3 \
      --retry-delay 1 \
      --retry-max-time 30 \
      --connect-timeout 30 \
      --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \
      http://1.1.1.1

   Now power on the router.

B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.

   1. Configure PC with a static IP address and setup an TFTP server.
   2. Put the firmware into the tftp directory.
   3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
   4. Power up the device and press 2, follow the instruction to set device and
      tftp server IP address and input the firmware file name. U-boot will then load
      the firmware and write it into the flash.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
546fced2a2 x86: add intel microcode entries to grub config
Create initrd enries for x86 images, that'll load intel microcode as
early as possible. To achieve that the test module for grub is enabled
which provides shell-like conditionals. Also restrict the late load of
microcode to AMD processors.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
51e199fbe8 x86: add packages files to image bootfs
Add files to bootfs image from selected as built-in packages, which want
to install files to targets boot file system.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
f78b261637 x86: mount writable bootfs
Mount boot file system with rw option to allow installation of packages
which install files to /boot directory.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Petr Štetiar
d42a7c4699 ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3735964 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Petr Štetiar
db4b6535f8 ath79: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions

 A) Serial console, U-Boot and TFTP

   1. Connect to serial header J1 on the PCB
   2. Power on device and enter U-Boot console
   3. Set up TFTP server serving an OpenWrt initramfs build
   4. Load initramfs build using the command tftpboot in the U-Boot cli
   5. Boot the loaded image using the command bootm
   6. Copy squashfs OpenWrt sysupgrade build to the booted device
   7. Use mtd to write sysupgrade to partition "firmware"
   8. Reboot and enjoy

 B) Experimental factory image flashing over SSH from airOS v6.1.7

   1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
      no other airOS version is currently supported
   2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
   3. cd ubnt-bullet-m2hp-openwrt-flashing
   4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:38 +01:00
Roman Yeryomin
ae2b43b873 ramips: fix ethernet for f5d8235-v2 board
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:58:17 +01:00
Russell Senior
e42327aa89 ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 09:47:27 +01:00
Roman Yeryomin
b0d6653ab8 rb532: drop 4.9 support
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:34:09 +01:00
Roman Yeryomin
9f13cde1fa rb532: switch to 4.14
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:33:01 +01:00
Roman Yeryomin
920845357f rb532: add 4.14 support
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:31:50 +01:00
Martin Schiller
18398abe1e lantiq/basefiles: use shutdown instead of stop when the system goes down
I can't see any reason why we shouldn't use shutdown for lantiq as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-11-25 19:26:55 +01:00
Petr Štetiar
82b34c1f60 imx6: image: ventana: Add missing BOOT_SCRIPT variable
This is probably theoretical problem as the Ventana is defined first in
the image Makefile, but once the position of the definition would change
in the future (alphabetical sorting?) it would get bootscript from the
previous board which would have BOOT_SCRIPT set.

Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-25 19:23:03 +01:00
Daniel Golle
7c4251d881 ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.

Reported-by: Arian Sanusi <openwrt@semioptimal.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Daniel Golle
51c094e703 kernel: enable CONFIG_BRIDGE_VLAN_FILTERING
This allows us to use the bridge as a managed switch and gracefully
handle mixed tagged and untagged frames. Prior to this, the only
alternative was creating one bridge per vlan which quickly becomes a
nightmare and still won't let you mix both tagged and untagged frames on
the physical port without some complex ebtables magic.

This is in line with the notion that OpenWRT is the network go-to swiss
army knife when you need a nice set-and-forget, low maintenance box to
handle a specific task.

Current builds of the ip-bridge package already fully support this
feature so the only requirement is enabling the kernel config.

This is disabled by default so existing bridge configurations will not
be affected.  This patch only gives the ability to turn it on with an
'ip link' command.  If there is interest, I could look into making the
feature accessible via uci configuration.

It causes about 3.1% hit on raw bridging speed, which is relatively
trivial considering that I had to use 300 byte packets to strain the CPU
enough to notice a slowdown at all.  The ER8 would chug along at wire
speed otherwise, and that's using only one core.  Since the typical
bridge use case on OpenWRT is wireless, I doubt it would be noticeable
at all.

With BRIDGE_VLAN_FILTERING

iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size:  208 KByte (default)
------------------------------------------------------------
[  3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0-10.0 sec   977 MBytes   820 Mbits/sec
[  3] Sent 3414986 datagrams
[  3] Server Report:
[  3]  0.0-10.0 sec   811 MBytes   680 Mbits/sec   0.000 ms
581210/3414986 (0%)

Without BRIDGE_VLAN_FILTERING

iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size:  208 KByte (default)
------------------------------------------------------------
[  3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0-10.0 sec   977 MBytes   820 Mbits/sec
[  3] Sent 3414990 datagrams
[  3] Server Report:
[  3]  0.0-10.0 sec   836 MBytes   701 Mbits/sec   0.000 ms
493950/3414990 (0%)

In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a
0.002% hit.  The exact 16KB is probably just due to how the kernel is
compressed.

Suggested-by: Jonathan Thibault <jonathan@navigue.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Rafał Miłecki
18c5e7ba91 ath79: specify "firmware" partition format for Ubiquiti UniFi
This affects:
1. Ubiquiti UniFi-AC-LITE/LR
2. Ubiquiti UniFi-AC-PRO
3. Ubiquiti UniFi-AC-MESH
4. Ubiquiti UniFi-AC-MESH PRO

Succesfully tested on UniFi AP AC Pro.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 19:04:29 +01:00
Hannu Nyman
3e19113d5d ath79: specify "firmware" partition format for WNDR3700 and v2
Specify the new "firmware" partition format for Netgear WNDR3700
and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third
device in the family.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-11-24 13:15:55 +01:00
Rafał Miłecki
c8a005fefd ath79: specify "firmware" partition format for TP-LINK Archer C7 v2
With this change it doesn't require trying parsers one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 12:46:00 +01:00
Rafał Miłecki
c87d47aee8 kernel: drop unused arch_split_mtd_part()
No single target/arch uses it and most likely there is no need to make
such a potential code target/arch specific.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 12:24:02 +01:00
Rafał Miłecki
f995e143ba kernel: add missing version.h include to the TP-LINK parser
Fixes: a29c8d685b ("kernel: add DT binding support to the TP-LINK parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 11:48:47 +01:00
Rafał Miłecki
a29c8d685b kernel: add DT binding support to the TP-LINK parser
It allows triggering it directly by specifying format in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 09:56:53 +01:00
Rafał Miłecki
ffd082aa38 ath79: specify "firmware" partition format for Netgear WNDR3800
It doesn't require trying parsers one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 08:46:59 +01:00
Rafał Miłecki
a22311e6a6 kernel: add DT binding support to the uimage parsers
It allows specifying default and Netgear parsers directly in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 08:31:56 +01:00