THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.
The first device is Globalscale ESPRESSObin. Some hardware specs:
SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
µSD card slot with footprint for an optional 4GB EMMC
4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
USB 2.0
µUSB port connected to PL2303SA (USB to serial bridge
controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
I2C, GPIOs, PWM, UART, SPI, MMC, etc
MiniPCIe slot
Misc: Reset button, JTAG interface
Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:
1. Interrupt boot process to run U-Boot command line,
2. Run following commands:
(for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
(for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
saveenv
3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
The Armada XP uses a Marvell PJ4Bv7 Processor for which already one
workaround for an errata is activated.
The Armada 285 uses a Cortex A9 r4p1 for which the Linux kernel provides
a workaround for ERRATA_764369, activate this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for kernel 4.14 to the mvebu target.
This also replaces the old sfp and phylink patches with new versions
from Russell's clearfog-4.13 branch
http://git.arm.linux.org.uk/cgit/linux-arm.git/log/?h=clearfog-4.13
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
