Commit graph

17326 commits

Author SHA1 Message Date
Felix Fietkau
1c8d155142 kernel: add missing config symbol for linux 3.18
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-22 23:20:30 +01:00
Thibaut VARENE
f6a52bf337 ar71xx: Enable mtdsplit support for RB SPI NOR devices
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.

Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.

Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:20 +01:00
Thibaut VARENE
53c862705d ar71xx: remove bogus "rb*)" catch-all from platform.sh
This patch replaces a dangerous catch-all with the exhaustive list of devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:19 +01:00
Thibaut VARENE
890daca9e2 kernel: mtdsplit: Add support for Mikrotik NOR firmware
The RouterBOOT bootloader does not care where the kernel lives in the SPI
flash, all that matters is that the kernel is wrapped in the custom yaffs
container as generated by kernel2minor.

This container has a fixed signature as follows:
00000000  00 00 00 01 00 00 00 01  ff ff 6b 65 72 6e 65 6c  |..........kernel|

This patch adds mtdsplit support for identifying that signature and
triggering the search for the rootfs. rootfs is expected at EB boundary since
we use wget mtd_find_rootfs_from(). We make no use of the yaffs file size
field because it contains invalid data in the image generated by kernel2minor.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-22 22:52:19 +01:00
Stijn Tintel
5c49fecf72 Revert "kernel: ar8327/ar8337: disable ARL access code to avoid lockups (FS#384)"
This reverts commit ec1a695daa.

Revert the workaround, the problem was properly fixed in
2374549916.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-02-22 11:56:27 +01:00
Thomas Reifferscheid
e01b034cdc ipq806x: fix fakerootfs position
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.

Fixes: FS#542

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-02-21 21:18:33 +01:00
Felix Fietkau
f66a0c93b3 archs38: only calculate entry point address when necessary
$(eval) runs even during prereq check, which can cause bogus error
messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-21 16:10:32 +01:00
Felix Fietkau
f77a1aac0b arc770: only calculate entry point address when necessary
$(eval) runs even during prereq check, which can cause bogus error
messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-21 16:10:30 +01:00
Alif M. Ahmad
2712497442 x86_64: Add support for EFI framebuffer (FS#515)
CONFIG_FB_EFI and CONFIG_FB_SIMPLE are needed to display console text on
EFI framebuffer.

CONFIG_FB_EFI is needed when the kernel is directly launched via EFI
shell or EFI startup.nsh script.

CONFIG_FB_SIMPLE is needed when launching the kernel via grub2 efi. In
this case, grub2 has prepared a gfxterm framebuffer and the kernel just
need to use the already prepared grub's gfxterm framebuffer to display
console text.

Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
2017-02-21 16:07:09 +01:00
Rafał Miłecki
75b530a51b bcm53xx: add kernel 4.9 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-20 14:12:30 +01:00
Weijie Gao
3ee793f601 ar71xx: fix vlan settings for some boards
For AR71XX devices, GMAC1 always connects port 0 of the built-in switch,
as the CPU port.

This patch sets correct vlan for some devices with wrong settings:
a) mark port 0 as CPU port, tagged
b) reverse port order, marking these ports untagged

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2017-02-20 09:27:43 +01:00
Thibaut VARENE
6e4549138d ar71xx: Add more boards to the routerboard serial detection patch
This patch enables serial console on the 435 series and the 953gs.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-20 09:20:48 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Mathias Kresin
bececcce86 lantiq: fix warning if ltq_atm modules are missing
Fixes the following warning on first boot if the ltq_atm modules are
not included in the image:

  ls: /lib/modules/4.4.49/ltq_atm*: No such file or directory

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:51:31 +01:00
Mathias Kresin
e88b36f4be lantiq: set the internet led interface according to wan interface
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:51:31 +01:00
Mathias Kresin
044a4eafd5 lantiq: introduce lantiq_is_vdsl_system
Move the code to check if the current system is a system with vdsl
support to a dedicate function to make it reusable.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:51:31 +01:00
Mathias Kresin
cfd16ecc48 lantiq: fix ARV7519RW22 switch port indexing
Fixes FS#454.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-18 16:51:31 +01:00
Felix Fietkau
72327d1757 ar71xx: fix ethernet PLL configuration for QCA956x
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-17 12:16:13 +01:00
Henryk Heisig
d6baeb5c48 ar71xx: fix lan ports on archer C59 and C60
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-02-17 10:30:48 +01:00
David Woodhouse
d16f433e42 x86: Add Geos profile for Geode subtarget
This makes the Geode images actually useful again. The Geos profile
should include the relevant hardware for that board, and the Default
profile adds the via-rhine adapter which seems to have been present in
the net5501 and alix targets killed in commit 9e0759ea26 ("x86: merge
all geode based subtargets into one").

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-17 10:30:38 +01:00
Karol Dudek
58fc50f1b0 ar71xx: add support for 8devices Lima board
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.

Specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO

Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery

Tested on:

- Lima development kit

Signed-off-by: Karol Dudek <karoiz@sli.pl>
2017-02-17 10:19:09 +01:00
John Crispin
a4efc9965c mediatek: add more missing symbols
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-16 20:25:47 +01:00
John Crispin
bb255f7429 ipq806x: add v4.9 support
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-16 20:25:32 +01:00
John Crispin
04c4b6f7fd mediatek: add config file for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-16 14:14:29 +01:00
Felix Fietkau
2bf9ea6a31 mvebu: add linux 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-16 17:17:15 +01:00
Günther Kelleter
2374549916 ar8216: flush ARL table during reset after init_globals
commit 33b72b8e0f
"ar8216: adjust ATU flushing in case of link changes"
introduced portwise flushing on link down events. Now the ARL table could
be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped
forever (depending on the entries collected while booting).

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
2017-02-16 17:17:05 +01:00
John Crispin
53f5d59fa1 mediatek: bump to v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-16 09:53:30 +01:00
Furong Xu
f885edef5a ramips: fix the number of uarts for MT7688
Same as MT7621 and MT7628, MT7688 allows up to 3 uarts

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:37 +01:00
Furong Xu
00343e18f2 ramips: fix PWM pin mux conflict in dtsi
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict

[    0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[    0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[    0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0  on device rt2880-pinmux
[    0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back

Keep PWM disabled.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:09 +01:00
Hauke Mehrtens
a11243578a kernel: update kernel 4.4 to version 4.4.49
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-16 00:46:29 +01:00
Hauke Mehrtens
236840eb47 kernel: update kernel 4.9 to version 4.9.10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-16 00:46:23 +01:00
Mirko Parthey
d517f04343 brcm47xx: fix button inversion for Asus WL-500W
The Asus WL-500W buttons are active high,
but the software treats them as active low.
Fix the inverted logic.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-16 00:06:22 +01:00
Mirko Parthey
ac3a4e7ae2 brcm47xx: fix USB driver choice for Asus WL-500W
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.

It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0

Choose a set of USB drivers which actually support this hardware.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-15 23:43:19 +01:00
Felix Fietkau
1e1a0592f8 kernel: fix crashes on MIPS when loading kernel modules under memory pressure
When memory is tight, modules may need to be loaded into vmalloc()
space. The code then has to generate jump trampolines which enable
relocations between vmalloc space and physical address space.

The code had a bug that was freeing these trampolines even when the
module was successfully loaded.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-15 12:35:17 +01:00
Thibaut VARENE
748e701b74 ar71xx: add preliminary kernel support for several RB SPI NOR devices
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.

This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.

The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.

Code has been successfully built and has no side effect (no impact on already
supported devices).

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE
b800453282 ar71xx: add new SPI NOR RB devices to the list of serial-enable patch
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE
b2044a7f60 ar71xx: add support for RB750r2
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2

Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)

This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
19f42663d2 ar71xx: add support for RB750UPr2
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

This ethernet router is based on the same platform as the wireless router hAP.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
8cbb2ac633 ar71xx: add support for RB951Ui-2nD
This patch adds support for the MikroTik RouterBOARD hAP
https://routerboard.com/RB951Ui-2nD

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE
c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Daniel Golle
d57223259b ramips: replace remaining instances of ralink, port-map
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-02-15 09:12:40 +01:00
John Crispin
6cb0372d42 ramips: fix mt7621 ethernet support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:12:00 +01:00
John Crispin
38f9d08f57 kernel: add missing symbol for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:11:11 +01:00
Chris Blake
9a6c932556 x86: Add board configs for the PC Engines APU2
This adds the default LED and network settings for the PC Engines APU2
when running under the x86 target.

[dwmw2: Change Ethernet port setup]
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-15 07:52:28 +01:00
David Woodhouse
add465f1be x86: Enable DIAG LED on Geos
Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's
do it by using the LED configuration instead of hard-coding it for each
board type. And try using /bin/board_detect to do the default behaviour,
on the first boot where the config hasn't yet been generated.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-15 07:52:28 +01:00
Chris Blake
27a635f0b4 x86: Move Traverse Geos configs into x86 base-files
This change moves the files in 657418d to the root of the x86 target.
This is done in preperation for adding more devices under other
subtargets.

CC: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-15 07:52:28 +01:00
Giuseppe Lippolis
35c60d18c5 ramips: export slic IRQ line in dwr-512
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-15 07:45:54 +01:00
John Crispin
c186a48fca octeon: only copy sysupgrade file if present
this caused

'mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory'

when running sysupgrade -n

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 06:36:21 +01:00
John Crispin
1753720261 octeon: bump to v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-14 17:14:27 +01:00