commit a2386c384d requires the
module to be static in the kernel.
So lets actually add support for it inside the kernel config.
Tested on Ventana
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.
Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.
The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.
For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:
- Ralink V11ST-FE
- Ralink AP-RT3052-V22RW-2X2
- MediaTek MT7628 EVB
- MediaTek MT7621 EVB
- UPVEL UR-326N4G
- Buffalo WZR-AGL300NH
Signed-off-by: Mathias Kresin <dev@kresin.me>
At the moment the padding steps are hardcoded. Especially images for
devices with a 4K sector size can be unnecessarily bloated using the
hardcoded padding steps.
It has been observed that 192Kb of padding was added to the image of a
4MB device, albeit due to the 4K sector size the minimum required extra
padding for the jffs2 rootfs_data is 20Kb.
In worst case it means that the image-size check could fail albeit
there is enough space for all selected packages
For device build code not exposing the blocksize, use the hardcoded
padding further on.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Allows to use the same unit for all definitions of the blocksize to be
consistent regardless of the used filesystem.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some devices (e.g. Tenda AC9 based on BCM47189B0) have BCM53125 with
port 5 connected to the second Ethernet interface on the SoC. In such
case there is no PHY and we need to force link manually.
This assumes port 5 can be marked as enabled for such devices. It's not
implemented yet unfortunately.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Don't expose dnsmasq version & other data to clients via the *.bind
pseudo domain. This uses a new 'NO_ID' compile time option which has been
discussed and submitted upstream.
This is an alternate to replacing version with 'unknown' which affects
the version reported to syslog and 'dnsmasq --version'
Run time tested with & without NO_ID on Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
e2fsprogs would fail linking with external toolchains which would not be able
to find several dependencies, explicit them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The insertion or removal of the sd-card cannot be detected
by the hardware itself. This is by design. To workaround this,
for the WNDR4700 unload/load the dwc2 module in case the
the special SD CARD GPIO line is low/high.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A few linux BSP's create a manifest file of installed packages for a given
target in order to help them understand exactly what's on their images. Create
one here as well as a build artifact since many users have an affinity to
prune down on packages to save valuable flash space.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
