Looks like the targets are Ubiquiti routers which don't come with any wireless cards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 42810
the driver did not handle all states correctly causing a deadlock of the i2c hw block.
Signed-off-by: Ing.Michele Mogioni <michele.mogioni@unimc.it>
SVN-Revision: 42807
This enables dedicated "rootfs" splitter by default. We still keep
CONFIG_MTD_SPLIT_SQUASHFS_ROOT, so the old (built-in) splitter will be
used as a fallback in case of problems.
Once we decide the dedicated partitioner works stable, we should remove
the old one completely.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42805
Some ISP seem to only do stateful DHCPv6 and not sending RAs.
This is technically broken because plain DHCPv6 doesn't carry routes.
We work around here by faking a default route to the DHCPv6 server
if we do not receive a useful RA from the ISP.
This workaround can be turned off with: option fakeroutes 0
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42803
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 42795
The build system sets a make variable TAR_OPTIONS to the unpacking
command, i.e. "-xf -". Now if an environment variable with the same
name is set, the make variable is automatically exported to the
environment. The make variable is added to the tar command in the
makefile, and tar adds the environment variable. This results in a
command like "tar -c /some/dir -xf - -xf -" which of course doesn't
work. It is also difficult to spot as the second "-xf -" is not
visible on the command line.
I suggest this is fixed by unexporting TAR_OPTIONS as I see no use
of the evironment variable, and it is changed from the original
value anyway.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
SVN-Revision: 42794
The AR9580 with the new ID can be found in the EnGenius ESR900 and the
QCA9880 without any subsystem IDs can be found in the EnGenius ESR1750.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
SVN-Revision: 42793
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 42782
