Change some flow-level unctions to return with an
error code in order to be able to report errors
to the core code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38068
This patch adds support for TP-Link TL-MR13U router with built-in 10AH
rechargeable battery.
The patch is based on kamwanlai's patch:
https://forum.openwrt.org/viewtopic.php?pid=206746#p206746
Updated to accommodate recent changes introduced with:
ar71xx: remove fs_* variables from image/Makefile
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4063/
[juhosg:
- refresh and rename rename 930-add-tl-mr13u-support.patch =>
625-MIPS-ath79-add-tl-mr13u-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38063
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38059
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37844
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37131
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36848
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36799
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
