Fix sysupgrade to determine the correct boot block device to use if
/proc/cmdline contains a PARTUUID root.
Change the preinit move_config() hook to use the UUID scanning code
from sysupgrade in order to avoid code duplication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42968
Enable the required squashfs and block2mtd support in the kernel in order
to be able to actually boot them.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42967
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42966
The Makefile for binutils creates a broken symlink to "binutils-linaro" in
"trunk/build_dir/toolchain-<target>_gcc-4.9-linaro_uClibc-0.9.33.2".
Modify the Makefile to point the symlink to the correct directory.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 42954
Fix the move_config() procedure to properly find the corresponding disk if
the rootfs was mounted by PARTUUID instead of a device node.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42946
This kmod is required by the Alix APU 1D4 to be reachable after
installing an x86-64 image.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42945
* Rewrite ndp proxy using kernel proxying
* Aid flash-renumbering in hybrid DHCPv6-mode
* Unicast RAs to RS senders
* Add support for router address
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42944
We still don't have a smart sysupgrade method, but at least we can use
UBI which provides some protection for rootfs (SquashFS).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42941
UBI requires PEBs to be formatted (with a valid UBI header) or empty
(0xFF), however CFE doesn't clear blocks after flashing the image. To
workaround this problem, teach UBI to recognize EOF mark in a similar
way JFFS2 handles that in OpenWrt.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42940
This change configures grub to mount the rootfs by PARTUUID instead of the
device path if CONFIG_TARGET_ROOTFS_PARTNAME is unset.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42936
- Add current buildroot scm url as base feed to feeds.conf
- Prefer feeds.conf over feeds.conf.default when generating the SDK feeds.conf.default
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42935
- Consider not installed feeds as well
- Add option to decide whether to comment disabled feeds
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42931
Inside every LuCI package you need to clear luci-indexcache and
sometimes when installing non LuCI pacakges it's also needed to clear
it. Easier put it into default_postinst().
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 42923
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
SVN-Revision: 42922
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42920
This patch adds missing architecture-specific headers for use with
eventfd(2). Fixes#16679.
Signed-off-by: Luis Dallos <ld@nkvd.ignorelist.com>
SVN-Revision: 42916
