This special dwc2 device definition for the Netgear WNDR4700
has been replaced by amcc,usb-otg-405ex.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.
Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M
By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.
The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.
This patch is a port of what legacy ifxmips_pci.c does.
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
The latest stock firmwares for US and EU regions have started checking the
region code.
Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some builders have troubles cloning the boot-wrapper-aarch64.git repository so
provide a mirror checksum to allow downloading from sources.lede-project.org
instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.
The MAC address numbering of the TEW-691GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:0C
WIFI: AA:BB:CC:DD:EE:0D
WAN: AA:BB:CC:DD:EE:0F
The MAC address numbering of the TEW-692GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:e4
WAN: AA:BB:CC:DD:EE:e5
2.4GHz: AA:BB:CC:DD:EE:e7
5 GHz: AA:BB:CC:DD:EE:e8
Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.
Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.
Set the label and compatible string according to the the PCI binding
documentation.
Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.
Use the usual eeprom for the soc wmac of the Dovado Tiny AC.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.
Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).
Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Since commit 484cb91 "sdk: bundle required firmware files" there is an
implicit dependency of the SDK on a prior Kernel compilation.
Change target/Makefile to make this dependency explicit to avoid race
conditions with parallel builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Switch to xz compression instead of using bz2.
This makes a considerable difference in size, ar71xx SDK from 60M to 35M.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.
Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Fixes the same hctosys init issue as described in commit
5481ce9a11
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
This bugfix enables FXS support on dabube based devices.
Changed "compatible" attribute from "vmmc" to "vmmc-xway".
The vmmc driver uses "vmmc-xway".
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.
Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
These boards do not have a switch, so they should have never been added
to this file in the first place.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).
The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.
Once this partition is added to a device, you can set your MAC doing the
following:
mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot
Where 00:18:0a:33:44:55 is your MAC address.
This was tested, and confirmed working on both the MR12 and MR16.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.
Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:
[ 2.427349] hctosys: unable to open rtc device (rtc0)
[ 3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Refresh patches for all targets supporting 3.18 and not marked broken.
Compile-tested on all targets using 3.18 and not marked broken.
Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refresh patches for all targets supporting 4.1 and not marked broken.
Compile-tested on all targets using 4.1 and not marked broken.
Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Changes to generic/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch based
on a90ee92337.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).
This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)
After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
loader), gzip compressed one, uncompressed one.
At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.
I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Linksys WRT300N V1 has pretty bugged CFE bootloader (it crashes in a lot
of situations) that doesn't accept .bin image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When building packages within the SDK, there is no Git revision history
available so prepopulate SOURCE_DATE_EPOCH in version.mk, similar to
how we handle REVISION already.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.
Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.
Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.
Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes.
This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
[sanitize all device tree files]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.
Both is fixed here.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
