Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.
The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All TP-Link TL-WR710N versions share the same machine code.
This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*
* Serial console is disabled in OEM non-beta firmwares and corresponding
GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
production (non-beta) U-Boot and firmware.
Currently not working:
1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
by some U-Boot versions.
Flash instruction under vendor GUI:
1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.
FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):
1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
turns on.
Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):
1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ag71xx_ethtool_set_ringparam() will return an uninitialized value on
success.
Found-by: Coverity Scan #1330877
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Fixes the following security vulnerabilities:
CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.
CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.
CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.
CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.
CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.71
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
If nand chip has no NAND_NO_SUBPAGE_WRITE flag on its options
ubifs can't use it mtd devices and the kernel crashes with error:
__nand_correct_data: uncorrectable ECC error
Signed-off-by: Sergey Sergeev <adron@yapic.net>
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.
Actually, DR344 has 6 GPIO-connected LEDs and one button:
- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan
WAN LED is connected directly with AR8035 PHY.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Hardware Specification (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Signed-off-by: Filip Moc <lede@moc6.cz>
This change is required to make the GBit switch work on my Mikrotik Routerboard RB2011UiAS-RM, and I assume that the other RB2011 variants are exactly the same in terms of the switch. I have tested the board without and with the patch and confirm that the GBit ports are not supported at all (i.e. no communication works) with the current version in trunk and that everything works with the patch applied. The test box has been running for a few days with the patch applied, and does not show any performance problems in a test setting. I have not used it with LEDE in production so far, but with a previous turnk version of OpenWRT for many years - with the same patch applied. I therefore have good indication that it is stable.
For the record, the switch chip on my test box is identified as
switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
The value 0x6f000000 has been taken from the table at https://wiki.openwrt.org/toh/mikrotik/rb2011uias with the previous discussion thread still online at https://lists.openwrt.org/pipermail/openwrt-devel/2014-December/029949.html.
One definite improvement from the older OpenWRT trunk version I have been running in production and current LEDE trunk is that the SFP interface can be kept in the default configuration without excessive kernel messages about it constantly going up and down. I have not yet tested an actual SFP module, though.
Performance seems to be reasonable. Routing between two GBit ports on that switch separated by different VLANs with the default firewall ruleset (and one additional rule two allow traffic between the VLANs), but without NAT, iperf3 results are:
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 508 MBytes 426 Mbits/sec 102 sender
[ 4] 0.00-10.00 sec 506 MBytes 425 Mbits/sec receiver
With a connection going through NAT (also 2 ports on the same GBit switch, same ruleset, but NAT active), routing performance drops to around 250 MBit/s.
(Note that RouterOS achieves beyond 900 MBit/s on the same hardware with the default rule set and the FastTrack rule active even for NAT, see https://wiki.mikrotik.com/index.php?title=Manual:IP/Fasttrack and http://www.mikrotik.com/download/share/FastTrack.pdf).
Summarizing, I strongly recommend to apply this patch in trunk, so that the GBit switch chip rev. 4 can be supported upstream in the next LEDE release (hopefully soon).
Signed-off-by: René Mayrhofer <rene@mayrhofer.eu.org>
changes the image version from hardcoded OpenWrt to
$VERSION_DIST. AirOS shows a notification with the image version
during a firmware upgrade.
fixes#582
Signed-off-by: Matthias Fritzsche <txt.file@txtfile.eu>
Refresh patches. A number of patches have landed upstream & hence are no
longer required locally:
062-[1-6]-MIPS-* series
042-0004-mtd-bcm47xxpart-fix-parsing-first-block
Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup
as it was incorrectly included upstream thus dropped from LEDE.
As it has now been reverted upstream it needs to be included again for
LEDE.
Run tested ar71xx Archer C7 v2 and lantiq.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[update from 4.4.68 to 4.4.69]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.
The device ist based on a Atheros AR9344 rev 3,
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card
The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)
Running from tftp:
The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
This adds support for Aerohive AP-121 access point.
Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:
dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan
This commit adds basic support for Rambutan development kit
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header
Flash instructions:
Stock firmware is OpenWrt, so use:
sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
nand erase.part ubi
nand write 80060000 ubi ${filesize}
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds the build option for the new UniFi AC Mesh.
It is a direct hardware copy from the AC Lite.
- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 1 1000M - POE
- Wireless:
2.4G: QCA9563
5G: UniFi Chip, QCA988X compatible
Thanks to Frank Dietz for testing.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[wrapped too long lines in mach-ubnt-unifiac.c]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
