Add a fucntion to get the a binary mac address from file. Use the new
function for mtd_get_mac_binary() to limit duplicate code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The image production rules does not have the initramfs-image
as a dependency. So, from make’s perspective initramfs
creation can run independently/in parallel with the image
generation code in the target's Makefile.
This is a problem for devices that have to use the initramfs
for the image creation and can lead to broken images.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the patch that was posted to ath10k-devel ML:
<https://patchwork.kernel.org/patch/10233491/>
|From: Thomas Hebb <tommyhebb@gmail.com>
|Subject: [PATCH] ath10k: search all IEs for variant before falling back
|Date: Wed, 21 Feb 2018 11:43:39 -0500
|[...]
|This patch fixes the issue by first searching the entire file for the ID
|with variant, and searching for the fallback ID only if that search
|fails. It also includes some code cleanup in the area, as
|ath10k_core_fetch_board_data_api_n() no longer does its own string
|mangling to remove the variant from an ID, instead leaving that job to a
|new flag passed to ath10k_core_create_board_name().
|
|I've tested this patch on a QCA4019 and verified that the driver behaves
|correctly for 1) both fallback and variant BDFs present, 2) only fallback
|BDF present, and 3) no matching BDFs present.
|
|Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension")
|Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Note: 937-ath10k-calibration-variant.patch has been reassigned a new 081
number, as it now ships with upstream.... But also because this patch
requires the change in ath10k_core_create_board_name().
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rename the dts file to match the used SoC type and drop the unnecessary
KERNEL_INSTALL from the image build code.
Remove the fixed rootfs and kernel partitions and create an image with
rootfs appended after kernel.
Setup a switch portmap matching the hardware and a default network/switch
configuration to make make the second lan port working. Use eth0 as lan
to have it consistent accross the target.
Use the power LED to indicate the boot status.
Sort the SoC entries within the dts by address and use dtc labels
whenever possible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This removes the block- and pagesize from the FritzBox 4040
image description, fixing incorrectly working sysupgrade.
With this commit, the default values for block- and pagesize are
used.
Signed-off-by: David Bauer <mail@david-bauer.net>
[chunkeey@gmail.com: removed 105-mtd-nor-add-mx25l25635f.patch as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sort the soc entries in the dts by address and use dtc labels whenever
possible.
Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an
IPQ4019.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There's an interaction issue between the clk changes:"
clk: qcom: ipq4019: Add the apss cpu pll divider clock node
clk: qcom: ipq4019: remove fixed clocks and add pll clocks
" and the cpufreq-dt.
cpufreq-dt is now spamming the kernel-log with the following:
[ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP
for freq 761142857 (-34)
This only happens on certain devices like the Compex WPJ428
and AVM FritzBox!4040. However, other devices like the Asus
RT-AC58U and Meraki MR33 work just fine.
The issue stem from the fact that all higher CPU-Clocks
are achieved by switching the clock-parent to the P_DDRPLLAPSS
(ddrpllapss). Which is set by Qualcomm's proprietary bootcode
as part of the DDR calibration.
For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked
at round 533 MHz (ddrpllsdcc = 190285714 Hz).
whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is
clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libext2fs breaks krb5 by always installing its own copies of libcom_err.so
and libss.so.
Move the libraries into separate libcomerr and libss packages respectively
and add a host build recipe to stage the required compile_et and mk_cmds
utilities for use by other packages.
This allows the krb5 package to be fixed to use the system wide libcomerr
and libss libraries.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[rename libcom_err to libcomerr, make compile_et and mk_cmds relocatable,
cleanup makefile, add dependency on host build, reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In the commit bde5e7a632 ("kernel: backport mtd implementation for
"compatible" in "partitions" subnode") patches that got accepted into
l2-mtd.git were backported to the kernels 4.9 and 4.14. Unfortunately
there was a regression report, patches were dropped and never reached
4.16.
This commit replaces these pseudo-backports with the latest version
that includes regression fix and futher changes that were requested.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Revert the changes I applied to aa5014dd1a ("ramips: mt7620n: enable
port 4 as EPHY by default").
The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load with
mtk_soc_eth 10100000.ethernet: no mdio-bus child node found
Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.
Fixes: FS#1428
Signed-off-by: Mathias Kresin <dev@kresin.me>
Support configuration in the form...
list ip6prefix 2001:db8:1234::/64
list ip6prefix 2001:db8:5678::/64
... to allow specifying multiple routed IPv6 prefixes.
Implements feature request FS#1361.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Commit f4d9d7a removed support for version specific patches; but it also
broke applying of patches in the patches glibc dir.
Fix the issue by setting PATCH_DIR to $(PATH_PREFIX)/patches similar as
musl/common.mk.
Signed-off-by: Xinxing Hu <xinxing.huchn@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
1f5a29c ip: do not add local routes for host dependencies
c06f842 device: add support for setting the isolate options for bridge ports
69aeaab interface-ip: fix route selection for host dependencies
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In kernels 4.0 and older that header file was located in some subdir of
arch/mips/include. Target brcm47xx supports kernels 4.4 and 4.9 only so
that code isn't needed anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If CONFIG_GPIO_SYSFS=n, compilation fails with
drivers/built-in.o: In function `gpio_export_with_name':
include/asm-generic/gpio.h:128: undefined reference to `__gpiod_export'
This is because the stub in that case has the wrong name,
_gpiod_export() - note the missing underscore (_) at the
start.
Fix the stub, and add the correct prototype for the real
implementation.
Signed-off-by: André Draszik <git@andred.net>
busybox tries to be smart and passes a number of additional flags to the
compiler. Unfortunately, the i386-specific flags break ABI compatiblity
with libc.
Fixes busybox crashes observed on x86-generic with GCC 7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Newer GCC versions are reported to improve code size on various ARM
devices, which is why newer u-boot versions require them now.
There have also been user reports of data corruption issues fixed on
MIPS by updating from GCC 5 to GCC 7.
This update was previously held up by these two MIPS compile issues,
which have since been fixed:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83496https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84790
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This updates musl from a commit between 1.1.18 and 1.1.19 to the final
release of the version 1.1.19.
This mostly fixes bugs in musl.
The size of the uncompressed binary is increased by about 4 KB.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Optimize the compiler output for larger cache blast cases that are
common for DMA-based networking.
On ar71xx, I measured a routing throughput increase of ~8%
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts the changes needed for the upstream b53 DSA switch driver
to use the OpenWrt b43 swconfig switch driver instead.
Tested-by: TheWerthFam <thewerthfam@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.
The first device is Globalscale ESPRESSObin. Some hardware specs:
SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
µSD card slot with footprint for an optional 4GB EMMC
4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
USB 2.0
µUSB port connected to PL2303SA (USB to serial bridge
controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
I2C, GPIOs, PWM, UART, SPI, MMC, etc
MiniPCIe slot
Misc: Reset button, JTAG interface
Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:
1. Interrupt boot process to run U-Boot command line,
2. Run following commands:
(for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
(for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
saveenv
3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.
The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.
Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
