Commit graph

124 commits

Author SHA1 Message Date
Michael Gray
bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
Damir Samardzic
bdb0de1bbc uboot-envtools: add support for ESPRESSObin and MACCHIATObin
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-04-25 20:37:28 +02:00
Sven Eckelmann
0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Piotr Dymacz
10ea53f900 ramips: add U-Boot env support for ALFA Network AC1200RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
Piotr Dymacz
3fc8f50f56 uboot-envtools: fix ALFA Network AWUSFREE1 support
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
John Crispin
54b275c8ed ipq40xx: add target
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Ryan Mounce
9f3f61a0d9 mvebu: add support for Turris Omnia
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.

An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.

Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.

Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.

Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem

Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv

Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.

Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-03-10 01:15:21 +01:00
Piotr Dymacz
f01b394266 uboot-envtools: add support for ALFA Network AWUSFREE1
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 23:40:16 +01:00
Piotr Dymacz
3b8a858d5c uboot-envtools: add support for YunCore T830
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
f487133322 uboot-envtools: add support for Samsung WAM250
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
c6bd0b4894 uboot-envtools: add support for WHQX E1700AC/E600G/E600GAC v2
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Karl Palsson
b2a5f7683b ar71xx: Add eTactica EG-200 support
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.

Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.

Flash instruction:
    Original firmware is based on OpenWrt.
    Use sysupgrade image directly in vendor GUI.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-02-13 10:01:53 +01:00
Piotr Dymacz
53e3df2e71 uboot-envtools: add support for GL.iNet GL-AR750
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
ec141c1f3d uboot-envtools: add support for ALFA Network R36A
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
b38ff7847b uboot-envtools: add support for ALFA Network N5Q
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 21:30:22 +01:00
Piotr Dymacz
62610129b2 uboot-envtools: add support for ALFA Network AP91-5G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Sven Eckelmann
9514cde2b9 uboot-envtools: add OpenMesh A42 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 07:58:44 +01:00
Luis Araneda
7293499f71 ipq806x: Sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
33f09cf151 ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree

Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script

Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Mathias Kresin
0674a99f7e kirkwood: sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Alberto Bursi
0e94df65ca uboot-envtools: add pogoplug v4
add pogoplug v4 envs support in uboot-envtools

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-01-09 22:06:55 +01:00
Mathias Kresin
c9e2c35f46 kirkwood: use the generic board detect
Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
0ebdf0c1d3 kirkwood: drop support for orphaned boards
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
224d4a96dd ramips: drop LinkIt Smart 7688 Duo userspace support
The  LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.

Since all relevant hardware is identical, drop the Duo special handling
in userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-21 01:05:16 +01:00
Mathias Kresin
63d7f7fc92 lantiq: use the compatible string as board name
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.

Don't add the former used boardname for boards which exists only in
master or evaluation boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Piotr Dymacz
c7fdff157e uboot-envtools: add support for Wallys DR342
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Felix Fietkau
184c92e7fb uboot-envtools: add support for Nokia WI2A-AC200i
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 12:27:44 +02:00
Kevin Darbyshire-Bryant
f2107fc328 ramips: improve Xiaomi Mi Router 3G support
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d

Improvements:

- Remove software watchdog as hardware watchdog now working as per
  commit 3fbf3ab44f for all mt7621
  devices.

- Reset button polarity corrected - length of press determines reboot
  (short press) vs. reset to defaults (long press) behaviour.

- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
  link and blink on activity.  Green LEDs driven directly by switch
  indicating any link speed and tx activity.

- USB port power on/off GPIO exposed as 'usbpower'

- Add access to uboot environment settings for checking/setting uboot
  boot order preference from user space.

Changes:

- Front LED indicator is physically made of independent Yellow/Amber,
  Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
  indicator, hence the colour behaviour is similar to an RGB LED. RGB
  LEDs are not supported at this time because they produce colour results
  that do not then match colour labels, e.g. enabling 'mir3g:red' and
  'mir3g:blue' would result in a purple indicator and we have no such
  label for purple.
  The yellow, red & blue LEDs have been split out as individual yellow,
  red & blue status LEDs, with yellow being the default status LED as
  before and with red's WAN and blue's USB default associations removed.

- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
  layout. eth0.1 is LAN, eth0.2 is WAN

- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
  leakage between kernel switch init and uci swconfig

uboot behaviour & system 'recovery'

uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed

last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2.  last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok.  If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.

NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.

Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.

Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.

Installation - from stock.

Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
  lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
  from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
  wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot

Recovery - to stock.

Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)

Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'

All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot

The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted.  Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2017-09-28 09:20:36 +02:00
Ram Chandra Jangir
9adfeccd84 uboot-envtools: Add support for IPQ806x AP148 and DB149
IPQ806x AP148 and DB149 boards didn't have the UCI ubootenv
section initialized, so the usage of fw_printenv required manual
configuration. With this change, the "fw_printenv" and "fw_setenv"
command will automatically work on NOR and NAND based platforms.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-08-30 18:12:48 +02:00
Mathias Kresin
60f6c2b2eb ramips: drop Edimax BR-6425 support
Code to build an image for the Edimax BR-6425 never existed.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:07:56 +02:00
Piotr Dymacz
8223dac99a uboot-envtools: add support for ALFA Network AP121F
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:14:06 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Camille Bilodeau
bdd3c94872 uboot-envtools: add Arduino Yun support
Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Marty Plummer
558d86923e ar71xx: add support for EnGenius ENS202EXT
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-05-30 14:15:25 +02:00
Mantas Pucka
cd9d0f9e97 uboot-envtools: add support for 8devices Rambutan
Signed-off-by: Mantas Pucka <mantas@8devices.com>
2017-05-15 22:43:33 +02:00
Mathias Kresin
18618695ae ramips: dont replace the board name
Use fixed led names and add each board variant instead of manipulating
the board name.

It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00
Felix Fietkau
ca44b9a0d4 pistachio: remove custom board detection override
Use device tree based model string

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Felix Fietkau
eb98bf605e pistachio: remove pistachio_board_name, use the generic function
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:22 +01:00
Ian Pozella
0d271cef80 target: add pistachio
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.

This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.

Note, this commit is just the initial board support hence the
following are not expected to work yet:
 * WiFi
 * Bluetooth
 * 6lowpan
 * Audio
 * Mikrobus uarts, user leds (clock dependency of 6lowpan chip)

The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.

Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
2017-03-22 11:43:22 +01:00
Felix Fietkau
7e798dab56 lantiq: remove lantiq_board_name, use the generic function instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-22 11:43:21 +01:00
Sven Eckelmann
2696b0ec1e package/uboot-envtools: add OpenMesh A40 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
bddb243640 package/uboot-envtools: add OpenMesh a60 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
88aa7eeee5 package/uboot-envtools: add OpenMesh OM2Pv4/-HSv4 support
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Alberto Bursi
760185972f uboot-envtools: add nsa325 envs
adding nsa325 envs for consistency with other kirkwoods

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-02-11 21:16:28 +01:00
Alberto Bursi
55ecceb84e uboot-envtools: add nsa310b envs
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-01-24 16:21:25 +01:00
Piotr Dymacz
1599a14b32 uboot-envtools: drop executable file attribute from files/ipq
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-20 09:35:36 +01:00
Piotr Dymacz
a9ce2ba31c uboot-envtools: fix Edimax BR-6425 board name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-20 09:35:36 +01:00
Piotr Dymacz
35ed3be59f uboot-envtools: fix code formatting style in uci-defaults files
Few minor code formatting style fixes, including:

- keep one board per line
- always use "|\" (for consistency)
- remove redundant double quotes and empty lines

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-20 09:35:36 +01:00
Piotr Dymacz
f70a2adca1 uboot-envtools: keep boards in alphabetical order
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-20 09:35:36 +01:00
Piotr Dymacz
c40477519e uboot-envtools: add support for YunCore SR3200 and XD3200
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00