Commit graph

43106 commits

Author SHA1 Message Date
Petr Štetiar
60dd181a76 base-files: diag.sh: Make it more generic towards DTS so it could be reused
I wanted to add status LEDs support to my imx6 based board and have
found out, that I could use diag.sh script found in ramips platform,
which seems to be also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

So I've extended the base diag.sh in a way, that if it detects any of
the DTS LED aliases, then it would use the generic DTS set_led_state
code.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-06 08:42:40 +01:00
David Bauer
68e59b61c6 kernel: add DT binding support to AVM EVA parser
It allows selecting split-firmware parser directly by
specifying image-format in the device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-06 08:42:40 +01:00
Rosen Penev
26dcaf58ee comgt: Fix 3g.sh permissions
3g.sh needs to be executable. 600 is not correct for that.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-12-06 08:42:39 +01:00
Jonathan Thibault
e93e2b6318 octeon: Evaluate board names in alphabetical order
Signed-off-by: Jonathan Thibault <jonathan@navigue.com>
2018-12-06 08:42:22 +01:00
Ram Chandra Jangir
9ed180b000 ipq806x: dts: Add support for RGMII RX and TX clock delays
This change enables support to select phy4 in RGMII mode and
enables RGMII TX/RX clock internal delays.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-12-06 08:15:50 +01:00
Ram Chandra Jangir
bf7719f22c kernel: ar83xx: Add support for three GMAC's connection
We have IPQ8064 AP161 board which has three GMAC's
 * RGMII x2
 * SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.

Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-12-06 08:15:27 +01:00
Daniel Halmschlager
99e212171a ar71xx: Add usb drivers in Archer C7 v4/v5 images
This commit adds the default usb packages
- kmod-usb-core
- kmod-usb2
- kmod-usb-ledtrig-usbport
for Archer C7 v4 and v5.
(The C7 v5 configuration is based on the v4, therefore the change for v4
also applies for v5.)

Signed-off-by: Daniel Halmschlager <dh@dev.halms.at>
2018-12-05 21:30:37 +00:00
Michael Heimpold
d6ac8ca76c base-files: fix several bashisms
For equality test a simple = is sufficient, the == is
usually disregarded as bashism.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-12-05 22:16:52 +01:00
Marek Lindner
8ad45992ac ipq40xx: fix openmesh sysupgrade with tar content out of order
The tar extraction depends on the order in which the files
are added to the tar file. Since the order is not guaranteed
and depends on the host system, the combined mtd write fails
with sysupgrade images built on some systems.
Fix by changing to tar file order independent mtd write.

Fixes: 86e18f6706 ("ipq806x: add support for OpenMesh A42")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-12-05 09:40:32 +01:00
Steven Lin
2b4ac79a79 ipq40xx: add support for EnGenius EAP1300
SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
NOR:    32 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button
LEDS:   Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm

2. Load image via GUI

a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.

3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin

Signed-off-by: Steven Lin <steven.lin@senao.com>
2018-12-05 09:40:32 +01:00
Stijn Tintel
e261c8b764 brcm2708-gpu-fw: add fw required for camera module
To be able to use the camera module, start_x=1 has to be set in
config.txt. This will cause the bootloader to load the GPU firmware that
contain the extra video codecs. Install these firmware files.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-05 00:39:53 +02:00
Stijn Tintel
42ca32ad2f brcm2708-gpu-fw: update to git HEAD
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-05 00:09:14 +02:00
Stijn Tintel
93a14b8f2a kernel: add missing symbol
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-04 22:45:08 +02:00
Stijn Tintel
f208f77811 mac80211: fix brcmfmac on brcm2708
An upstream change broke brcmfmac when loaded with modparam roamoff=1.
As we are carrying a patch that enables roamoff by default on the
brcm2708 target to improve stability, wireless is currently broken
there. Add a patch to fix brcmfmac with roamoff=1.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-04 22:45:08 +02:00
Mathias Kresin
f381cbcb5f ramips: fix Netgear EX3700/EX3800 wireless driver selection
Fix the typo to select kmod-mt76x2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-04 20:40:27 +01:00
Felix Fietkau
4fd7882822 mt76: update to the latest version
5a5b396 mt76: throttle transmission of buffered multicast packets
8084323 mt7603: implement code for adjusting energy detect CCA thresholds
8929a6e mt7603: increase MCU timeout
f2ba65f mt7603: update firmware to 20161027164355
0ad998b mt7603: increase aggregation limits (based on vendor driver changes)
da00af0 mt7603: clear bit 18 in MT_SEC_SCR to fix ICV error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-12-04 12:28:56 +01:00
Rafał Miłecki
f98fde2db4 Revert "kernel: use add_mtd_partitions() helper when using OpenWrt parsers"
This reverts commit 7e88753ace.

Using subpartitions (hierarchical layout) resulted in calling MTD ops of
parent partition instead of master device ops. That was expected and
should work but testing revealed some bugs.

Apparently the way MTD_ERASE_PARTIAL is implemented in the OpenWrt
breaks something and using parent partition ops triggers using that
code.

On SmartRG SR400ac it was resulting in:
[  225.487519] jffs2: Erase at 0x01ac0000 failed immediately: errno -22
on the second boot (for some reason erasing was starting over) and it
was breaking flash access in a long term.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 15:50:26 +01:00
Pawel Dembicki
e9a9b7d1ed ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- WIFI 5G LED not working
- flash is very slow

The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang
40692f0fb5 ramips: mt7620: select only the matching mt76 driver
Because every device has selected the corresponding mt76 driver, we can
now disable the mt76 metapackage by default to make sure that other
devices (those don't need mt76) avoid selecting unwanted packages.

We can find the hardware specifies and determine the dependencies on
these sites:
  https://wikidevi.com/wiki/
  https://openwrt.org/toh/hwdata/

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang
7a32a73e52 ramips: mt7620: drop mt76 driver for boards without mt76 wireless
These boards don't have a mt76 wireless at all and don't need any of the
mt76 family drivers.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Mathias Kresin
55101877d3 ramips: mt7620: disable PCIe if nothing is attached
All boards neither expose the PCIe as Mini-PCIe nor have anything
attached to the PCIe Bus. Disable PCIe for those by dropping the node
from the dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-03 15:34:56 +01:00
Chen Minqiang
14b81c909f ramips: mt7620: add missing pci wifi nodes to dts files
These devices has pci wifi but not defined in dts:
 HC5761
 HC5861
 TINY-AC

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Rafał Miłecki
7e88753ace kernel: use add_mtd_partitions() helper when using OpenWrt parsers
This helper uses hierarchical partitions layout following the way
upstream parsers work. It's closer to what we should use when mainlining
our solutions. It also doesn't require hacky casting of struct
mtd_partition to the const.

THIS WILL AFFECT KERNEL PRINTING PARTITIONS IN THE LOG

Something like:
[    3.930158] 0x0000004e0000-0x000001fb0000 : "rootfs_data"
will get replaced by:
[    3.907338] Creating 1 MTD partitions on "rootfs":
[    3.912142] 0x00000031d400-0x000001ded400 : "rootfs_data"

It's important to understand that "rootfs_data" in above example is a
*subpartition* of the "rootfs" now. To get absolute addresses (e.g. for
some debugging purposes) one has to add them to the "rootfs", e.g.
[    3.912548] 0x0000001c2c00-0x000001fb0000 : "rootfs"

(0x1c2c00 + 0x31d400 = 0x4e0000)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 11:26:05 +01:00
Rafał Miłecki
e24983e710 kernel: backport 2 mtd partitioning fixes
This improves handling of subpartitions.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 10:34:12 +01:00
Florian Eckert
675eb747aa openvpn: add list element parsing
For the parameters tls-cipher and ncp-ciphers more than one option can
be used in the OpenVPN configuration, separated by a colon, which should
be implemented as a list in order to configure it more clearly. By
adding the new OPENVPN_LIST option to the openvpn.options file with the
tls-cipher and ncp-cipher parameters, uci can now add this option as a
"list" and the init script will generate the appropriate OpenVPN
configuration from it.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2018-12-03 09:54:03 +01:00
Rafał Miłecki
966ba6daa4 kernel: fix downloading rcX releases
They are no longer stored in the "testing" subdirectory and are not
available as .tar.xz archives. If -rc is detected download it from the
git.kernel.org and use .tar.gz.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 09:34:57 +01:00
Russell Senior
73127a878d ath79: add support for Ubiquiti AirRouter
Indoor low-power router with 2.4 GHz radio

CPU:    Atheros AR7241 rev 1
RAM:    32 MB
Flash:  8 MB NOR SPI
Switch: Atheros AR7240
Ports:  1x WAN, 4x LAN 10/100 Ethernet
WLAN:   Atheros AR9285 (2.4 GHz)
USB:    1x USB2 host port

Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.

UART settings: 115200, 8N1

                LEDs
        +--------------------------
        |
        |
        |
        |
        |
        |
        |
        |
    VCC | x x
     RX | * x
        | x x
        | x x
     TX | * x
    GND | * x
        |
        |
        |
        |
        +--------------------------
                ETHERNET PORTS

Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:56 +01:00
Russell Senior
20ec6af15e ath79: split ubnt outdoor device leds into separate dtsi
Move common LED configuration into a separate includible dtsi.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:49 +01:00
Eneas U de Queiroz
3fb45576ac cryptodev-linux: move from packages feed
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is actually a build dependency for /dev/crypto support in openssl.
Since it is a kernel module, it belongs here anyway.

- Removed Nikos Mavrogiannopoulos as maintainer.
- Streamlined make flags

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2018-12-03 07:50:24 +01:00
Tomasz Maciej Nowak
c288ad9c2b x86: make sysupgrade.tgz reachable again
Moving binding mount before check for saved sysupgrade configuration
made it unreachable. Fix it by moving binding mount after the check.

Fixes: f78b2616 (x86: mount writable bootfs)
Reported-by: Lucian Cristian <luci@powerneth.ro>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-12-03 07:38:20 +01:00
Jo-Philipp Wich
9808bd2799 Revert "base-files: fwtool: Fix wrong checksum on combined-image with metadata"
This reverts commit 41770add03.

The fwtool_check_image() procedure is used by `sysupgrade --test` which must
not alter the image under test in any way.

Currently, when the LuCI ui or any other sysupgrade wrapper first invokes
sysupgrade --test to verify the compatibility of the image and then calculates
the sha256sum over it, the resulting checksum will differ from the original
image since the test invocation will implicitely strip the metadata trailer.

To properly fix the underlying issue, the combined image checksumming code
must be modified to skip the metadata trailer.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-12-02 16:05:44 +01:00
Mathias Kresin
78ca6a5578 ramips: merge relocate compile into build recipe
Compile the loader if the relocate-kernel image recipe is used and get
rid of the legacy build code to do so.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-30 09:04:29 +01:00
Pawel Dembicki
465d57370f ramips: specify "firmware" partition format in JBOOT devices
Specify firmware partition format by compatible string.

List of devices:
-DWR-116-A1
-DWR-118-A2
-DWR-512-B
-DWR-921-C1
-LR-25G001

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-30 00:22:04 +01:00
Pawel Dembicki
b5597d5cc9 kernel: add DT binding support to the jimage parser
It allows specifying jimage parser directly in the DT.

Tested on LAVA LR-25G001

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-30 00:22:04 +01:00
Valentín Kivachuk
30a7ab8f61 ramips: add support for MTC Wireless Router WR1201
MTC Wireless Router WR1201 is the OEM name of the board. It is also sold
rebranded as STRONG Dual Band Gigabit Router 1200.

Specification:
- SoC: MediaTek MT7621A (880 MHz)
- Flash: 16 MiB
- RAM: 128 MiB
- Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN)
- Ethernet speed: 10/100/1000
- Ethernet ports: 4+1
- 1x USB 3.0
- 1x microSD reader
- Serial baud rate of Bootloader and factory firmware: 57600

The OEM webinterface writes only as much bytes as listed in the
uImage header field to the flash. Also, the OEM webinterface
evaluates the name field of uImage header before flashing (the
string "WR1201_8_128")

To flash via webinterface, is mandatory to use first initramfs.bin
and after (from the OpenWrt) the sysupgrade.bin

Some notes:
- Some microSD will not work:

  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: card claims to support voltages below defined range
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card

Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
2018-11-30 00:20:28 +01:00
Hans Dedecker
493c1d1766 odhcpd: update to latest git HEAD
d404c7e netlink: fix triggering of NETEV_ADDR6LIST_CHANGE event
ae6cf80 config: correctly break string for prefix filter

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-11-29 21:46:12 +01:00
INAGAKI Hiroshi
d70ec3008d ramips: specify "firmware" partition format
Specify firmware partition format by compatible string.

formats in ramips:

- denx,uimage
- tplink,firmware
- seama

It's unlikely but the firmware splitting might not work any longer for
the following boards, due to a custom header:

- EX2700: two uImage headers
- BR-6478AC-V2: edimax-header
- 3G-6200N: edimax-header
- 3G-6200NL: edimax-header
- BR-6475ND: edimax-header
- TEW-638APB-V2: umedia-header
- RT-N56U: mkrtn56uimg

But it rather looks like the uImage splitter is fine with the extra
header.

The following dts are not touched, due to lack of a compatible string in
the matching firmware splitter submodule:

- CONFIG_MTD_SPLIT_JIMAGE_FW
    DWR-116-A1.dts
    DWR-118-A2.dts
    DWR-512-B.dts
    DWR-921-C1.dts
    LR-25G001.dts
- CONFIG_MTD_SPLIT_TRX_FW
    WCR-1166DS.dts
    WSR-1166.dts
- CONFIG_MTD_SPLIT_MINOR_FW
    RBM11G.dts
    RBM33G.dts
- CONFIG_MTD_SPLIT_LZMA_FW
    AR670W.dts
- CONFIG_MTD_SPLIT_WRGG_FW
    DAP-1522-A1.dts

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-29 13:15:44 +01:00
Mathias Kresin
1977be8bd0 ramips: unifiy sysupgrade file extensions
Use .bin as file extension where possible. The user doesn't need to that
sysupgrade images for NAND boards are tarballs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-29 13:15:44 +01:00
Mathias Kresin
7f00123d63 ramips: remove duplicate image build variables
Remove image build variables which are set to the same value as the
default image build recipe.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-29 13:15:44 +01:00
Petr Štetiar
221d3e0234 ramips: bdcom-wap2100: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:15:44 +01:00
Petr Štetiar
1576666d67 ath79: ubnt-xw: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:10:50 +01:00
Petr Štetiar
9f563267d2 ath79: ubnt-bullet-m-xw: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:10:38 +01:00
Jo-Philipp Wich
1416b63dcb rules.mk: fix syntax error
Fix broken assignment operator added in a previous commit.

Fixes db73ec9f51 ("rules.mk: add INSTALL_SUID macro")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-29 12:33:15 +01:00
Jo-Philipp Wich
b0261ee5e9 rules.mk: add INSTALL_SUID macro
This is useful for packages that want to stage SUID executables.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-29 12:06:16 +01:00
Tony Ambardar
8806da86f5 base-files: fix prerm return value, align with postinst code
The return value of a package prerm script is discarded and not returned
correctly by default_prerm(). This allows other operations like service
shutdown to "leak" their return value, prompting workarounds like commit
48cfc826 which do not address the root cause.

Preserve a package prerm script return value for use by default_prerm(),
sharing the corresponding code from default_postinst() for consistency.
Also use consistent code for handling of /etc/init.d/ scripts.

Run Tested on: LEDE 17.01.4 running ar71xx.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2018-11-29 11:52:56 +01:00
Felix Fietkau
5c9ad4fa6e ramips: fix MTD EEPROM offset for TL-WR840N v5
The previous offset was invalid and pointed to the end of the partition,
which was causing issues with mt76

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-29 11:45:44 +01:00
Karl Vogel
ae980458ab sdk: find kernel modules when KDIR is a symlink
The find statement would not return any results if the KDIR_BASE pointed to a
symlink. Ran into this issue due to a custom Kernel/Prepare that was installing
a symlink to the kernel directory.

The extra slash at the end fixes this scenario and does no harm for targets that
have a proper KDIR.

Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
2018-11-29 09:36:14 +01:00
Petr Štetiar
8ba6e95eed ramips: bdcom-wap2100: Enable mt7610e 5GHz radio
The 5GHz radio of this device uses an mt7610e PCI-E chip, which has
been recently started to be supported.

 mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
 mt76x0e 0000:01:00.0: ASIC revision: 76100002
 mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
 mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Petr Štetiar
26ad357192 ramips: bdcom-wap2100: Set firmware partition format to denx,uimage
Specify firmware partition format to denx,uimage in compatible DTS property.

 2 uimage-fw partitions found on MTD device firmware
 Creating 2 MTD partitions on "firmware":
 0x000000000000-0x00000017f72b : "kernel"
 0x00000017f72b-0x000000f70000 : "rootfs"

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Petr Štetiar
795211093f ramips: bdcom-wap2100: Fix boot failure by adding partitions compatible property
Flash partitions were moved under partition table node, but addition of
compatible property was omitted which lead to following boot failure:

 VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
 Please append a correct "root=" boot option; here are the available partitions:
 1f00           16384 mtdblock0
  (driver?)
 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00