The ebtables code relies on the `-nostartfiles` linker argument to execute the
extension modules' `_init()` functions automatically which is not working
reliably across all supported targets and gcc versions.
Running an ebtables executable linked this way just crashes with a segmentation
fault at runtime on program startup, e.g. on ARM architectures.
In order to fix the issue ...
- remove the use of the -nostartfiles linker flag
- rename the init procedures to a generic name without implicit semantics
- explicitely annotate those init procedures as constructors
The patch has been taken from the Alpine Linux distribution at
http://git.alpinelinux.org/cgit/aports/tree/main/ebtables/fix-extension-init.patch
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
dnsmasq's dnssec time checking method now uses a ntp hotplug mechanism,
therefore dnsmasq.time is redudant and no longer needs to be explicitly
excluded from sysfixtime.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Change dnsmasq's dnssec time check handling to use time validity
indicated by ntpd rather than maintaining a cross boot/upgrade
/etc/dnsmasq.time timestamp file. This saves flash device wear.
If ntpd client is configured in uci and you're using dnssec, then
dnsmasq will not check dnssec timestamp validity until ntpd hotplug
indicates sync via a stratum change. The ntpd hotplug leaves a status
flag file to indicate to dnsmasq.init that time is valid and that it
should now start in 'check dnssec timestamp valid' mode.
If ntpd client is not configured and you're using dnssec, then it is
presumed you're using an alternate time sync mechanism and that time is
correct, thus dnsmasq checks dnssec timestamps are valid from 1st start.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
V2 - stratum & step ntp changes indicate time is valid
V3 - on initial flag file step signal dnsmasq with SIGHUP if running
V4 - only accept step ntp changes. Accepting both stratum & step could
result in unpleasant script race conditions
V5 - Actually only accepting stratum is the correct thing to do after
further testing
V6 - improve handling of non busybox ntpd
if sysntpd not executable
dnsmasq checks dnssec timestamps
else
sysntp script disabled - look for timestamp file - allows external mechanism to use hotplug flag file
sysntp script enabled & uci ntp enabled - look for timestamp file
sysntp script enabled & uci ntp disabled - dnsmasq checks dnssec
timestamps
fi
/etc/os-release is the standard distribution release information
file, therefore add it (and image configuration options for
fields not previously present in LEDE). Once it is deemed
reasonable the non-standard openwrt_release, openwrt_version,
and device_info files could be removed (that is with this patch
we consider them deprecated in favour of the standard file).
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
After the conversion from legacy device profiles to the newer profile
information embedded in the image building code, the legacy recipes got
triggered twice with different eval depths, leading to shell syntax errors
when processing certain images.
The double processing was caused by the remaining Image/Build macro in
legacy.mk which serves as main entry point for the new style image build code
in conjunction with the newly introduced LegacyDevice/* macros which caused
the legacy image build fallback code to kick in.
In order to fix the issue, rework all legacy macros to work under the legacy
image build wrapper and remove the Image/Build macro of legacy.mk to prevent
legacy profiles getting executed in the context of the new build code.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Calibration data for QCA99x0 in this device has bogus macaddress.
The data cannot be modified directly, as it breaks checksum control.
Instead change the macaddress from phy add hotplug event.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
In the upstream kernel and the upstream squashfs4 tools the xz
compression header looks the following:
struct disk_comp_opts {
__le32 dictionary_size;
__le32 flags;
};
We added some other members and also moved some existing members. Place
the members which are already in upstream header at the same position
as in that kernel and add our own at the end. The kernel should not
have a problem when there are some additional members and just ignore
them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.
If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With update of binutils for ARC (this is now based on upstream 2.26)
we noticed issues with loadable kernel modules.
Something like that was happening:
--------------------->8-------------------
mbcache: unknown relocation: 49
insmod: can't insert './mbcache.ko': invalid module format
--------------------->8-------------------
More details could be found in that discussion in binutils mailing list:
http://thread.gmane.org/gmane.comp.gnu.binutils/74662
As of now the simplest work-around is to disable in-kernel unwinder
for now. That will at least allow us to use modules again.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: John Crispin <john@phrozen.org>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ethernet, ADSL2+ and LEDs are fully functional.
Supporting the two TAE ports and SIP gateway was not attempted.
The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
The patch has been run-tested and the relevant dmsg logs are as the
following
[ 0.762447] Creating 5 MTD partitions on "spi0.0":
[ 0.767217] 0x000000000000-0x000000010000 : "u-boot"
[ 0.775139] 0x000000010000-0x000000020000 : "bdinfo"
[ 0.781014] 0x000000020000-0x000000fe0000 : "firmware"
[ 0.810558] 2 uimage-fw partitions found on MTD device firmware
[ 0.815043] 0x000000020000-0x000000170000 : "kernel"
[ 0.821925] 0x000000170000-0x000000fe0000 : "rootfs"
[ 0.827587] mtd: device 4 (rootfs) set to be root filesystem
[ 0.831937] 1 squashfs-split partitions found on MTD device rootfs
[ 0.837983] 0x0000005c0000-0x000000fe0000 : "rootfs_data"
[ 0.845621] 0x000000fe0000-0x000000ff0000 : "backup"
[ 0.851445] 0x000000ff0000-0x000001000000 : "art"
While at it, convert to new build method
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
puts br2684ctl init after ADSL init instead of before, so that the ESI
is set at the right time, and for consistency with the PTM driver.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The bootloader uses 30 MHz as the SPI frequency for flash on the Germany and
North America models, and 50 MHz for it on the worldwide model, but the Lantiq
SPI driver in OpenWrt and LEDE may access the flash differently such that
writes are capped at 20 MHz, leading to read errors reported on the worldwide
model at 30 MHz.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The EASY80920 is available with the A1X and the A2X chip version
depending on the board version. Add both firmware versions to device
tree and make the driver load the correct version depending on the chip
version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This image format is used by Lantiq's / Intel's UGW version 6.1 to 7.1.
These images can be flashed onto a board with the SoC vendor boot
loader as a replacement for the vendor firmware.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The lantiq kernel arch code selects CONFIG_RESET_CONTROLLER always, so
it is always selected when the lantiq target is build. we do not need
support for unselected CONFIG_RESET_CONTROLLER option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Added optional command line option for patch-image tool
Default 16KB size is still maintained as this is an optional argument.
if one wants to specify or increase size they can provide this option.
sample usage: patch-dtb <file> <dtb> [dtb max size]
Signed-off-by: Vishnu Swaroop Duddu <duddu.swaroop@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of having CFE_EXTRAS for every device that need specific block sizes
and image offset, let's define a couple of vars which can be customized for
each device.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices require padded images in order to prevent CFE from flashing them
to the wrong offset.
For small flashes (4/8) this is no big deal, but for larger flashes (16/32) this
implies 8 and 16 MB images, which is way too large and some devices aren't
capable of flashing them through sysupgrade.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The configuration preservation mechanism fails to keep items was are unset
as unset. For busybox this causes issues when building with custom
settings in the SDK. Therefore preserve busybox unset settings.
In addition we preserve non-package selection unset settings because
they may be important for making sure we compile and identical
package for packages that are recompiled in the SDK.
Now that SDK not longer ships .config this becomes relevant for
any use of the SDK.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
Original URL got 303 redirect which then also dropped the commit id
leading to different file revision & MD5 mismatch.
Corrected URL & clarified commit ID use in Makefile
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The only difference is a field in the image tag header, so just define
two images for it instead of treating them as separate devices.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
External IRQs are currently broken, fix the BCM6345_EXT_IRQ driver.
Since the adoption of the new driver irq-bcm6345-ext, in Chaos Calmer,
external IRQs don't work. It seems there were some minor errors at the initial
development of the driver.
This patch fixes the ticket https://dev.openwrt.org/ticket/21613
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
