Commit graph

46 commits

Author SHA1 Message Date
Andrey Polischuk
0f21873f7f ar71xx: fix LED defines for TP-Link TL-WR740N v6
Signed-off-by: Andrey Polischuk <androld.b@gmail.com>
[changed commit subject, dropped redundant kernel config symbol]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:15:25 +02:00
Filip Moc
43e4e1f4a5 Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400
Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:40 +02:00
Filip Moc
a639cbfd00 ar71xx: Add support for TP-Link MR6400
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Hardware Specification (v1.0 EU):
 - SoC: QCA9531
 - Flash: Winbond W25Q64FV (8MiB)
 - RAM: EtronTech EM6AB160TSE-5G (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 2NIC (3x100M + 1x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 12V 1A

Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:21 +02:00
John Crispin
bad2f9c4dc Revert "ar71xx: Add support for Teltonika RUT900"
This reverts commit 224e5f5efa.

pepe2k pointed out that this was not ready to merge

Signed-off-by: John Crispin <john@phrozen.org>
2017-05-18 15:31:47 +02:00
Steffen Weinreich
224e5f5efa ar71xx: Add support for Teltonika RUT900
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.

The device ist based on a Atheros AR9344 rev 3,

Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card

The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)

Running from tftp:

The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-18 14:47:53 +02:00
Piotr Dymacz
190db43615 ar71xx: tp-link.mk: always include device version in image and DEVICE_TITLE
There are currently several supported TP-Link devices without specified
version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510,
TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there
are already more than one version of them on the market.

For devices like Archer C5, which second version is based on a total
different platform, missing version number in DEVICE_TITLE (used in
menuconfig) might be misleading for users.

To make it less confusing for users and easier to maintain in future,
include version number in image name and DEVICE_TITLE for all TP-Link
devices, even if there is only one version of device at the moment.

Also, keep DEVICE_TITLE in same format for all TP-Link devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
2017-04-03 12:29:07 +02:00
Vittorio Gambaletta
539e2a78f0 ar71xx: add TP-LINK TL-WR841N/ND v12 image
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).

If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.

The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2017-04-03 12:29:07 +02:00
Mathias Kresin
86a0cbb333 treewide: select ath10k firmware explicit
Do not rely on the default firmware selected by ath10k.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Piotr Dymacz
597c9f0be5 ar71xx: image: fix indentation
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 22:02:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Piotr Dymacz
56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Piotr Dymacz
a4d12aed30 ar71xx: image: fix DEVICE_TITLE for several devices
Be consistent with form and format of the vendor names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-03 05:10:14 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Radek Dostál
3561d89ad6 ar71xx: RE450: enable building of TP-Link RE450
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:06 +01:00
Tal Keren
0d9d980ecd firmware-utils: kernel image generator for TP-Link RE450
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Matthias Schiffer
324bdf3ecc
ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build command
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-21 23:29:00 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
Matthias Schiffer
0495181529
ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combined
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-20 14:38:48 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Henryk Heisig
0d760bfba8 ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partition
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-16 11:01:18 +01:00
Matthias Schiffer
9cac5e8be0
ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11
The latest stock firmwares for US and EU regions have started checking the
region code.

Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-11 03:29:59 +01:00
Henryk Heisig
4ad68fa0a2 ar71xx: tl-wpa8630: Fix kernel lenght
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Matthias Schiffer
83f7ec31f8
ar71xx: set EU region code for TP-Link TL-WA901ND v4
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.

This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.

Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-15 19:09:56 +02:00
Amir Rachum
4c36bcc567
ar71xx: build image for Archer C7 v2 IL
TP-Link uses a different region coding mechanism for IL firmware for the Archer
C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV.

Signed-off-by: Amir Rachum <amir@rachum.com>
2016-10-09 21:13:09 +02:00
Matthias Schiffer
01e2024754
ar71xx: set region code of TP-Link TL-WDR3600/4300 to US
There are currently two stock firmwares for the TL-WDR3600/4300, a US and
a universal version. Both allow installing images with US region code, so
we don't need to provide multiple images.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-15 19:34:28 +02:00
Matthias Schiffer
b063faa2c8
ar71xx: separate TP-Link TL-WDR3600/4300/4310 profiles
Simplify modifying some of the images without affecting the others.

While we're at it, also unify the profiles to use := syntax and add "v1" to
the TL-WDR4300 name to make things more consistent.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-15 19:33:30 +02:00
Matthias Schiffer
fa0096f6cc
ar71xx: generate US- and EU-specific images for the Archer C7 v2
TP-Link has started providing US- and EU-specific stock firmwares that only
allow upgrading to firmwares with the same region code. Provide factory
images for both these regions.

To avoid confusing users outside these regions, we still provide a
"universal" factory.bin without a region code, although flashing either of
the US and EU images would work as well.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-08-28 20:04:52 +02:00
Chuanhong Guo
d1b20a3659 ar71xx: fix profile name of Mercury MW4530R
The mw4530r-v1 profile in tp-link.mk is for Mercury MW4530R.
There is no such a device called TL-WDR4530.
Also change MERCURY to Mercury in /lib/ar71xx.sh

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-15 15:18:35 +02:00
Felix Fietkau
63b525dd6b image: add a helper variable for getting kernel/rootfs from within image Build/* templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-31 12:25:25 +02:00
Felix Fietkau
f1e085adfe ar71xx: add ath10k firmware to profile defaults where ath10k is used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-22 16:06:39 +02:00
Jo-Philipp Wich
8d1218ca73 ar71xx: merge profiles into image building code
- Remove old style device profiles and convert them to device definitions
  within the image building code

- Fix the legacy build macros for the changed eval depth in the legacy
  image build wrapper

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-27 11:10:15 +02:00
John Crispin
3874773503 Revert "ar71xx: fix legacy image building"
This reverts commit 59e98b27c9.

and

Revert "ar71xx: merge profiles into image building code"

This reverts commit 636089ead6.

these are still causing issues

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-23 19:33:31 +02:00
John Crispin
636089ead6 ar71xx: merge profiles into image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
Alexander Couzens
8241479605 tools/tplink-safeloader: split CPE210 from CPE510 profile
The CPE210 was still described for the OEM upgrade as compatible,
even the wireless configuration isn't compatible anymore between
both series (2ghz and 5ghz).
Update the CPE210 image profile to use the new profile.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-27 15:55:13 +02:00
Alexander Couzens
b7864453f6 ar71xx: switch ordering and template to improve readability
The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-27 15:55:06 +02:00
Ash Benz
7eb1a7e956 include/image.mk: move build step tplink-safeloader to image.mk
Move tplink-safeloader from target/linux/ar71xx/image/tp-link.mk to include/image.mk

Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Felix Fietkau
64b8bb3b69 ar71xx: split tp-link image building code into a separate file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-23 12:19:21 +02:00