This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.
This gives users without a serial console connection some
measure of safety.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47433
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
Add a new config option "channels" for mac80211 wifi devices. It's only
valid if automatic channel selection is used and restricts the channel
selection to one of the given channels.
config wifi-device
list channels 1
list channels 6
list channels 11
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47427
as conntrack and conntrackd are completely independent programs,
serving a different purpose.
Also split by other distributions, as Debian and Ubuntu.
Signed-off-by: Ulrich Weber <uw@ocedo.com>
SVN-Revision: 47424
default configuration will fill up disk by
writing /var/log/conntrackd-stats.log
Introduced due init script auto start.
Signed-off-by: Ulrich Weber <uw@ocedo.com>
SVN-Revision: 47422
In order to set the multicast rate for mesh point interfaces the "mesh join"
was made explicit and moved to mac80211_setup_vif(), similar to how it is
done for IBSS interfaces.
Previously, the mesh join was made implicit in case authentication (i.e.
$key) was not used when creating the interface in mac80211_prepare_vif(),
while using authentication would create the interface first, then join
later in mac80211_setup_vif() by starting authsae.
Signed-off-by: Nils Schneider <nils@nilsschneider.net>
SVN-Revision: 47408
Seems the default one is not working as expected.
The way that reload should work is that the 'start' service
call should return 1 (if lldpd is running) and then a normal
restart would be called.
However, for lldpd a reload would mean just clearing all custom TLVs
(if they're configured) and reloading the configuration.
So, this patch adds a reload hook, which would:
- 'start' lldpd if it's not running (because we return 1 if not running)
- reload configuration if it is running (also previously
clearing custom TLVs if present)
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47367
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47364
r46861 introduced a new option eapol_version to hostapd, but did not
provide a default value. When the option value is evaluated,
the non-existing value causes errors to the systen log:
"netifd: radio0: sh: out of range"
Add a no-op default value 0 for eapol_version. Only values 1 or 2 are
actually passed on, so 0 will not change the default action in hostapd.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47361
This fix contains 2 parts:
- kernel 4.1: backport upstream patch "perf build: Do not fail on missing Build file"
- add NO_LZMA=1 to perf MAKE_FLAGS to disable LZMA support
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47338
If building usbmon support then you'll likely want to have
USB support in libpcap as well.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
SVN-Revision: 47265
It looks like the bzip2 package does not install any shared libs
and has no build rules to install any shared libs.
So, for the host build we're installing the libbz2 shared libs manually
so that other modules can link against them.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47245
The CONFIG_BT_HCIUART_ATH3K may not be "m", therfore we cannot inherit the
kmod selection state. Force the "CONFIG_BT_HCIUART_ATH3K" symbol to "y" in
order to avoid `warning: symbol value 'm' invalid for BT_HCIUART_ATH3K` and
subsequent kconfig stalls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47237
This is another useful gadget driver that can allow an OTG port to act as a
mass storage device.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47225
Adds the package to select the mvsw61xx module present in the 3.18/4.0/4.1
kernels.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47224
FHS mandates presence of /var/tmp on compliant systems.
The lack of /var/tmp was discovered when using MIT Kerberos libraries
which default to that location for storing credentials cache.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 47219
Update iperf3 to point to the correct project website. Prior URL was the
old iperf2 website.
Signed-off-by: Karl Palsson <karlp@remake.is>
SVN-Revision: 47184
The two commits
5162e3b0ee7bd1d0fd6e75e1ca7993a1834b5291
"allow request handlers to disable chunked reponses"
and
618493e378e2239f0d30902e47adfa134e649fdc
"file: disable chunked encoding for file responses"
broke the chunked transfer encoding handling for proc responses in keep-alive
connections that followed a file response with http status 204 or 304.
The effect of this bug is that cgi responses following a 204 or 304 one where
sent neither in chunked encoding nor with a content-length header, causing
browsers to stall until the keep alive timeout was reached.
Fix the logic flaw by inverting the chunk prevention flag in the client state
and by testing the chunked encoding preconditions every time instead of
once upon client (re-)initialization.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47161
One second is not enough for some devices to ackowledge null data frame
which is sent at the end of ap_max_inactivity interval. In particular,
this causes severe Wi-Fi instability with Apple iPhone which may take
up to 3 seconds to respond.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 47149
Seems the match pattern was being adapted from 'eth0' to ' eth0'
because of the way I added the procd command args.
This did not seem to be a problem when there were multiple interfaces,
just on devices with single interfaces for lldpd to listen on.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47136
This URL can be embedded e.g. within UPnP announcements where a link
to the manufacturer's homepage is desired.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47135
OpenVPN 2.3 added a route-pre-down option, to run a command before
routes are removed upon disconnection.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
SVN-Revision: 47134
Install header files into same location as pkgconfig/libnl-3.0.pc says:
Cflags: -I${includedir}/libnl3
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 47102
Recently all targets have been updated to call nand_do_upgrade directly.
It's not needed anymore to leave a magic /tmp/sysupgrade-nand-path mark
during image check.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47079
When using FullMAC drivers (e.g. brcmfmac) we don't get mgmt frames so
check for banned client in probe request handler won't ever be used.
Since cfg80211 provides us info about STA associating let's put a check
there.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47064
There is no RFC requirement that DHCPv6 servers must reply with a link local
address and some ISP servers in the wild appear to using addresses in the ULA
range to send DHCPv6 offers.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47048
Some modules may require only libnl-genl, some
libnl-route and fewer would require libnl-nf.
This patch splits the entire libnl package into smaller
more granular libs that can be installed individually as required.
Also added libnl*.so symlinks for convenience.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47037
Since r46834, IPv6 support is builtin if selected. Therefor, dependencies
on kmod-ipv6 can no longer be fulfilled, since it is not a module anymore.
Signed-off-by: Arjen de Korte <arjen+openwrt@de-korte.org>
SVN-Revision: 47022
Even though there are not many users left within the OpenWrt tree it seems
this function broke during the kernel 3.18 transition.
Fix it by providing a workdir as required by overlayfs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47015
Using protocol qmi does not work since qmi.sh is not executable.
Setting option dhcp explicitely to 0 actually enables it.
This patch fixes both problems.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 47014
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Our ruleset requires kernel support for conntrack state matching, therfore
depend on the require kmod. Fixes#20542.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46990
'opkg list' command only displays the available packages' name, version and
description. It would be useful to also see the approximate size of the
available package.
This patch extends "opkg list" command with "--size" to optionally show also
the *.ipk size.
* Default behaviour is to list the available packages as earlier:
"name - version - description"
* with "--size" the output of is "name - version - size - description".
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 46980
- Simplify user spec parsing code
- Alias IPKG_INSTROOT to shorten code
- Quote variables where appropriate
- Remove a useless-use-of-cat instance
- Suppress errors in case control or list files are missing
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46975
This call is no longer supported.
Maybe a come-back for it would be to use a config /etc/lldpd.conf
or /etc/lldpd.d/<some-file>.conf
Signed-off-by: Alexandru Ardelean <aa@ocedo.com>
SVN-Revision: 46966
OpenWrt should support an optional /etc/profile.d directory like
most other Linux distributions. This allows packages to install
their own scripts into /etc/profile.d/ directory.
The file suffix should make clear, that these scripts
are (sourced) shell-snippets. If the user needs e.g. php or lua,
one must make sure that the interpreter is called.
The reverse failsafe test makes sure, that the effective returncode is 0.
A typcal usecase is the inclusion of private helpers,
special variables or aliases, which at the moment needs
patching the sourcecode and is not well maintainable.
Now the builder can simply add there files.
v1 initial work of Hendrik Lüth <hendrik@linux-nerds.de>
v2 changes regarding RFC (e.g. thomas.langer@lantiq.com)
v3 changes regarding RFC (e.g. mschiffer@universe-factory.net)
v4 keep it simple and mimic OpenWrt style
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 46965
This patch fix https://lists.openwrt.org/pipermail/openwrt-devel/
2015-August/034979.html. As the peak detect calibration is set
incorrectly.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46948
this need to be applied after my work on ujail (procd git)
ujail doesn't depend on seccomp and some archs dont support seccomp
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 46936
Thanks to Sylwester Petela for testing my patch (successfully on an
ADSL connection) and for pointing out some configuration mistakes.
Others (including me) have also successfully tested this extensively
on VDSL connections.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46920
DWC2 driver has config symbol CONFIG_USB_DWC2_DEBUG_PERIODIC which
should be defined for the module build.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46916
Expose the "lists_dir" configuration file option as command line
switch so that we can override it for the Image Builder environment.
Also add a more standard PKG_MAINTAINER variable while touching
the Makefile.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46911
The driver only supports wl18xx-fw-4.bin and does not support the old
firmware wl18xx-fw-3.bin and more.
The wl18xx-conf.bin file was removed upstream it does not fit all
devices any more, see this on how to generate one:
http://processors.wiki.ti.com/index.php/Open_Source_Wireless_Connectivity_wlconf
If someone has a config file for the common platforms with the wifi nic
OpenWrt uses please send a patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46887
