This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.
Signed-off-by: Leon M. George <leon@georgemail.eu>
The kernel configs for all targets should have the version in the
filename, for clearness and consistency across all targets.
It is also expected by the update_kernel.sh script.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
I did not port the regulator and power patches from Stefan Wahren
because I talked to him and he told me that work on this is currently
stalled. And since AFAIK nothing depends on these patches, leaving them
out seems reasonable.
I build minimum default configurations and run-tested them on both
I2SE Duckbill devices and Olimex Olinuxino Maxi boards successfully [1].
[1] Tested:
- debug uart is working
- boot without any obvious kernel problem
- network is coming up and data transfer is possible
- Olinuxino: USB detects a plugged-in pen drive
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
[refreshed config and patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In preparation for bumping mxs target to 4.9, disable a bunch of configuration
symbols that provoked config prompts.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch fixes a problem where the AR8035 PHY can't be
detected on the Cisco Meraki MR24, when the ethernet cable
is not connected during boot.
Russell Senior reported:
|This appears to be a problem during probing of the AR8035
|phy chip. When ethernet has no link, the phy detection fails,
|and eth0 is not created. Plugging ethernet later has no effect,
|because there is no interface as far as the kernel is
|concerned. The relevant part of the boot log looks like this:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
(<https://bugs.lede-project.org/index.php?do=details&task_id=687>)
Fixes FS#687
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)
To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.
The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.
The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Except for renames and line changes the only conflict was in
allocate_partition in handling MTD_WRITEABLE. Hopefully it was handled
correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This mtd_roundup_to_eb helper was introduced years ago in the commit
daec7ad768 ("kernel/3.10: add separate rootfs partition parser") and
it was probably supposed to simplify code a bit.
With the recent upstream commit 1eeef2d7483a7 ("mtd: handle partitioning
on devices with 0 erasesize") the logic in allocate_partition got
slightly more complex and we can't use this simple helper anymore as it
doesn't support MTD_NO_ERASE properly.
There also isn't any real gain from this helper, so it's probably easier
to just don't use it *or* work on upstreaming it to avoid maintenance
cost.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On boards which don't have a distinct internet and dsl led, use the
shared LED to indicate the xdsl line state and any traffic that is
send/received via the netdev. This traffic doesn't necessarily need to
be internet traffic.
Rename the shared LED of existing configs to "dsl", to match the new
defaults. The configuration of the to be renamed LED is identical with
the new defaults.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Allows to use a single LED for line init status indication and to show
any rx/tx activity on a synchronized dsl line.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.
Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).
Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The Cisco ON100 device is a Kirkwood based router:
SoC: Marvell 88F6282 1600Mhz
SDRAM memory: 512MB DDR3 1333Mhz
Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
Flash memory: 512MB
2 bi-colour status LEDs (green/red)
1 Reset button
1 USB 2.0 port (on back)
1 SDIO slot (on back)
This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".
Flashing can be performed over tftp, once "dhcp" has been issued:
tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
nand erase 0x0c0000 ${filesize}
nand write ${loadaddr} 0x0c0000 ${filesize}
Once flashed, set environment variables to boot:
setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
\; bootm
saveenv
Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
Evaluation boards are left in component form to ease flashing
using vendor tooling and instructions. These boards also do
not include the EOF marker in the UBIFS as the bootloaders
are recent and easily upgradeable.
The end product boards use factory.bin images based on the
dts layout and include EOF markers as bootloader UBI support
is not determined.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
All TP-Link TL-WR710N versions share the same machine code.
This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*
* Serial console is disabled in OEM non-beta firmwares and corresponding
GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
production (non-beta) U-Boot and firmware.
Currently not working:
1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
by some U-Boot versions.
Flash instruction under vendor GUI:
1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.
FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):
1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
turns on.
Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):
1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
