Commit graph

41784 commits

Author SHA1 Message Date
Alex Maclean
2f23a0583a ramips: RE350: add rootfs offset to header
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-26 07:04:43 +02:00
Alex Maclean
408c54b02f firmware-utils: tplink-safeloader: add dynamic partitions
Add support to dynamically split the firmware partition into os-image
and file-system partitions. This is done by replacing those entries in
the partition table with a single unified firmware partition, which is
then split according to actual kernel image size.

The factory image will have the file-system partition aligned to a 64K
erase block, but the sysupgrade image skips this and aligns only the
JFFS2 EOF marker to squeeze out more space.

This should prevent further creeping updates to the kernel partition
size while maximizing space for the overlay filesystem on smaller
devices.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-26 07:04:09 +02:00
Alex Maclean
0a2f21fa71 firmware-utils: mktplinkfw: add rootfs offset for combined images
Add an option (-O) to calculate rootfs offset for combined images.

This is needed for the TP-Link mtdsplit driver to locate the rootfs
when the start is not aligned to an erase block. This will be the
case for sysupgrade images produced by tplink-safeloader with upcoming
dynamic partition splitting.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-26 07:03:57 +02:00
Stijn Tintel
34e22653ac mac80211: enable ath10k LED support by default
Commit 61d57a2f88 adds ath10k LED
support, but doesn't add an option to actually enable it.

After enabling this option, a LED named ath10k-phy0 appears in sysfs,
and a trigger can be assigned to it. Since 60deb3cdef the default set
trigger is the tpt one.

Enable it by default, as most devices using ath10k chips shouldn't be
severely space-constrained. There are likely many devices that can
benefit from having it enabled, like my testing device.

Before:
   text    data     bss     dec     hex filename
 245311    8899      16  254226   3e112 ath10k_core.ko

After:
   text    data     bss     dec     hex filename
 245979    8899      16  254894   3e3ae ath10k_core.ko

Tested on a D-Link DAP-2695-A1 (ar71xx).

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-06-25 22:00:05 +02:00
Mathias Kresin
60deb3cdef mac80211: ath10k: use tpt LED trigger by default
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-25 20:52:18 +02:00
Franz Flasch
8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch
abb7524683 ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.

Use the mii-bus property instead to manage the switch via a mdio bus.

Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch
d4ac26ec49 kernel: rtl8366-smi: add Realtek switch management via mii-bus
Current version of rtl8366-smi module only supports Realtek switch
managment via two gpio lines. This adds Realtek switch
management via mii_bus. Tested on a Tp-link Archer C2 v1 (Mediatek
SoC mt7620a based)

dts-file configuration should look like this:

rtl8367rb {
	compatible = "realtek,rtl8367b";
	realtek,extif1 = <1 0 1 1 1 1 1 1 2>;
	mii-bus = <&mdio0>;
};

&ethernet {
	status = "okay";
	mtd-mac-address = <&rom 0xf100>;
	pinctrl-names = "default";
	pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;

	port@5 {
		status = "okay";
		mediatek,fixed-link = <1000 1 1 1>;
		phy-mode = "rgmii";
	};

	mdio0: mdio-bus {
		status = "okay";
	};
};

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Mathias Kresin
f9e7f19334 kernel: rtl8367b: drop redundant compatible
Remove the compatible without vendor prefix. It is formal wrong and not
used in the tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-25 20:52:18 +02:00
Yousong Zhou
c4aadbdaf6 dropbear: let opkg manage symlinks of ssh, scp
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2018-06-25 15:21:24 +08:00
Matthias Schiffer
4b50854a60
musl: sys/socket.h: fix SO_PEERSEC value on MIPS
Differing from all other archs supported by musl, MIPS defines SO_PEERSEC
to 30 instead of 31.

Patch has also been submitted upstream.

Reported-by: Andrey Jr. Mlenikov <temnota.am@gmail.com>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-24 17:24:53 +02:00
Adrian Schmutzler
5c5bf8b865
ar71xx: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:06:31 +02:00
Adrian Schmutzler
2524febf79
ar71xx: Add TP-Link Pharos v2 board detection
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.

Code was written mostly by Alexander Couzens <lynxis@fe80.eu>

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:02:01 +02:00
Axel Neumann
65c05301c2 Re-enable arbitrary IPv6 addresses as outer ip4-in-ip6 tunnel source address
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.

The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.

Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-23 09:47:05 +02:00
Jo-Philipp Wich
333e609703 build: change version.mk defaults to OpenWrt
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-06-22 13:45:03 +02:00
John Crispin
ebe1216c7c iptables: set nonshared flag
this makes sure that offloading support is properly included for v4.14 targets.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-22 11:46:21 +02:00
Kristian Evensen
4def81f30f mediatek: Add support for the UniElec U7623-02
This commit adds support for the MT7623A-based UniElec U7623-02 router,
with eMMC storage and 512MB RAM. The router can be delivered with NAND
Flash and more memory, but I only have access to the one configuration.
The DTS is structured in such a way that adding support for
more/different storage/memory should be straight forward.

The device has the following specifications:

* MT7623A (quad-core, 1.3 GHz)
* 512MB RAM (DDR3)
* 8GB storage (eMMC 4.5)
* 2x normal miniPCIe slots
* 1x miniPCIe slot that is connected via an internal USB OTG port
* 5x 1Gbps Ethernet (MT7530 switch)
* 1x UART header
* 1x USB 3.0 port
* 1x SATA 3.0
* 1x 40P*0.5mm FPC for MIPI LCD
* 1x SIM slot
* 12x LEDs (2 GPIO controlled)
* 1x reset button
* 1x DC jack for main power (12V)

The following has been tested and is working:
* Ethernet switch
* miniPCIe slots (tested with Wi-Fi cards)
* USB 3.0 port
* sysupgrade
* reset button

Not working:
* The miniPCIe connected via USB OTG. For the port to work, some MUSB
glue must be added. I am currently in the process of porting the glue
from the vendor SDK.

Not tested:
* SATA 3.0
* MIPI LCD

Installation:

The board ships with u-boot, and the first installation needs to be done
via the bootloader using tftp. Step number one is to update the MBR of
the eMMC, as the one that ships with the device is broken. Since the
device can ship with different storage sizes, I will not provide the
exact steps for creating a valid MBR. However, I have made some
assumptions about the disk layout - there must be one 8MB recovery
partition (FAT32) and a partition for the rootfs (Linux).

The board loads the kernel from block 0xA00 (2560) and I have reserved
32MB for the kernel (65536 blocks). I have aligned the partitions on the
erase block size (4096 byte), so the recovery partition must start on
block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to
start on sector 90112.

In order to install the mbr, you run the following commands from the
u-boot command line:

* tftpboot ${loadaddr} <name of mbr file>
* mmc device 0
* mmc write ${loadaddr} 0x00 1

Run the following commands to install + boot OpenWRT:

* tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz
* run boot_wr_img
* run boot_rd_img
* bootm

Recovery:

In order to recover the router, you need to follow the installation
steps above (no need to replace MBR).

Notes:

* F2FS is used as the overlay filesystem.

* The device does not ship with any valid MAC address, so a random
address has to be generated. As a work-around, I write the initial
random MAC to a file on the recovery partition. The MAC of the WAN
interface is set to the MAC-address contained in this file on each boot,
and the address of the LAN-interfaces are WAN + 1. The MAC file is kept
across sysupgrade/firstboot.

My approach is slightly different than what the stock image does. The
first fives bytes of the MAC addresses in the stock image are static,
and then the last byte is random. I believe it is better to create fully
random MAC addresses.

* In order to support the miniPCIe-slots, I needed to add missing
pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream
dtsi.

* One of the USB3.0 phys (u3phy2) on the board can be used as either USB
or PCI, and one of the wifi-cards is connected to this phy. In order to
support switching the phy from USB to PCI, I needed to patch the
phy-driver. The patch is based on a rejected (at least last time I
checked) PCI-driver submitted to the linux-mediatek mailing list.

* The eMMC is configured to boot from the user area, and according to
the data sheet of the eMMC this value can't be changed.

* I tried to structure the MBR more nicely and use for example a
FAT32-parition for the kernel, so that we don't need to write/read from
some offset. The bootloader does not support reading from
FAT32-paritions. While the command (fatload) is there, it just throws an
error when I try to use it.

* I will submit and hope to get the DTS for the device accepted
upstream. If and when that happens, I will update the patches
accordingly.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-06-22 11:25:52 +02:00
Chen Minqiang
e317bb06fd kernel: cleanup offload hooks on netdev unregister
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-06-22 11:01:42 +02:00
John Crispin
cac1a4be66 mac80211: drop 355-ath9k-limit-retries-for-powersave-response-frames.patch
several people reported this bug to be causing drop out issues

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-22 09:43:56 +02:00
Ansuel Smith
134e832814 mac80211: ath10k fix vht160 firmware crash
When the 160mhz width is selected the ath10k firmware crash. This fix this problem.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2018-06-22 09:31:32 +02:00
Ansuel Smith
61d57a2f88 mac80211: ath10k add leds support
This adds support for leds handled by the wireless chipset.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2018-06-22 09:31:32 +02:00
David Thornley
cb262b0939 wwan: Add support for Gemalto Cinterion cellular modules
Includes specific support for PH8(1e2d-0053) / ELS61(1e2d-005b) modules.

Note for ELS61, the serial driver changes from serial option(ttyUSB) to usb-cdc (ttyACM).

Two additional fixes in this commit resolve issues with ttyACM devices: -

* wwan.sh - sys-fs has a subdirectory indirection (*/tty/ttyACMx) which was not handled properly
* wwan.usb - dependent scripts were not included, so this never actually called proto_set_available for example (and relied on inadvertent call for ttyUSB case)

Signed-off-by: David Thornley <david.thornley@touchstargroup.com>
2018-06-22 09:31:32 +02:00
Hans Dedecker
b8bdeace39 busybox: rename udhcpc-remove-code-which-requires-server-ID-to-be-on patch
Move udhcpc-remove-code-which-requires-server-ID-to-be-on patch from 500
to 400

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-21 22:48:23 +02:00
Hans Dedecker
c6e50075f2 busybox: udhcpc: replace udhcpc_no_msg_dontroute patch by upstream fix
Replace 204-udhcpc_no_msg_dontroute patch by the upstream busybox fix
which removes the code which requires the server ID to be on local
network

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-21 22:33:35 +02:00
Mathias Kresin
004fe89620 lantiq: fix arcadyan vg3503j switch port indexing
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-21 22:00:03 +02:00
Chuanhong Guo
ed40173dfc ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:00:02 +02:00
Stijn Tintel
f9a42ae2d7 kernel: define THERMAL_EMERGENCY_POWEROFF_DELAY_MS
Enabling CONFIG_ATH10K_THERMAL on targets that don't have CONFIG_THERMAL
enabled in their kernel config causes build to fail due to missing
symbol THERMAL_EMERGENCY_POWEROFF_DELAY_MS. Add it to kmod-thermal.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-06-21 20:02:22 +03:00
Daniel Golle
a704a2c06f ltq-vdsl-fw: fix ltq-vdsl-vr9-vectoring-fw-installer package install
The package is not being generated otherwise, which is fatal because
it is part of the subtargets default package set...

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-21 12:00:12 +02:00
Felix Fietkau
4fb27cc9d8 mt76: update to the latest version
1d4ca10 mt76x2: track rssi for gain adjustment per station

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-21 11:19:05 +02:00
Tobias Schramm
5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Tobias Schramm
c0167abcb0 ramips: Add lzma-loader targets
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Tobias Schramm
4fa85a625f ramips: Add support for mt7621 to lzma-loader
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Deng Qingfang
feb0a0bf22 ramips: fix Newifi D1 mtd partition
Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-06-21 06:54:42 +02:00
Kevin Darbyshire-Bryant
3b11b225b3 wireguard: bump to 0.0.20180620
0bc4230 version: bump snapshot
ed04799 poly1305: add missing string.h header
cbd4e34 compat: use stabler lkml links
caa718c ratelimiter: do not allow concurrent init and uninit
894ddae ratelimiter: mitigate reference underflow
0a8a62c receive: drop handshake packets if rng is not initialized
cad9e52 noise: wait for crng before taking locks
83c0690 netlink: maintain static_identity lock over entire private key update
0913f1c noise: take locks for ss precomputation
073f31a qemu: bump default kernel
bec4c48 wg-quick: android: don't forget to free compiled regexes
7ce2ef3 wg-quick: android: disable roaming to v6 networks when v4 is specified
9132be4 dns-hatchet: apply resolv.conf's selinux context to new resolv.conf
41a5747 simd: no need to restore fpu state when no preemption
6d7f0b0 simd: encapsulate fpu amortization into nice functions
f8b57d5 queueing: re-enable preemption periodically to lower latency
b7b193f queueing: remove useless spinlocks on sc
5bb62fe tools: getentropy requires 10.12
4e9f120 chacha20poly1305: use slow crypto on -rt kernels on arm too

Compiled-for: ar71xx, lantiq
Run-tested-on: ar71xx Archer C7 v2 & lantiq HH5a

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-20 22:10:33 +02:00
Christo Nedev
48f311a112 brcm2708: Add wifi driver, firmware and NVRAM for Raspberry Pi 3 b
2708 -> 43430 -> pi0w

2709 -> 43430 -> pi3b
2709 -> 43455 -> pi3bplus

2710 -> 43430 -> pi3b
2710 -> 43455 -> pi3bplus

Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
2018-06-20 21:50:14 +02:00
Hans Dedecker
a9222e0328 odhcp6c: update to latest git HEAD
b99c1f6 odhcp6c: remove len check in option parsing handle

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-20 15:42:22 +02:00
Arvid E. Picciani
bf39d5594b ar71xx: add support for TP-LINK Archer C7 v5
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2018-06-20 15:36:19 +02:00
Daniel Engberg
c6e02b49f6 octeon: Add and set CPU type Octeon+ as default
The lowest CPU type used by supported Octeon platform
is Octeon+ (EdgeRouter Lite) while EdgeRouter Pro/ER-8 uses
Octeon II which is backwards compatible with Octeon+.

Sources:
https://community.ubnt.com/t5/EdgeRouter/EdgeRouter-Pro-CPU/td-p/654599
https://www.cavium.com/octeon-II-CN68XX.html
"OCTEON II family is fully software compatible with the widely-adopted
OCTEON Plus family"

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-06-20 15:36:02 +02:00
Robert Marko
4bb2532ec1 ethtool: Update to 4.17
Tested on 8devices Jalapeno(ipq40xx)
Introduces following changes
* Fix: In ethtool.8, remove superfluous and incorrect \
* Fix: fix uninitialized return value
* Fix: fix RING_VF assignment
* Fix: remove unused global variable
* Fix: several fixes in do_gregs()
* Fix: correctly free hkey when get_stringset() fails
* Fix: remove unreachable code
* Fix: fix stack clash in do_get_phy_tunable and do_set_phy_tunable
* Feature: Add register dump support for MICROCHIP LAN78xx

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-06-20 15:36:02 +02:00
Daniel Golle
3d20bee2cd ltq-vdsl-fw: add meaningful version information
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-20 14:39:22 +02:00
Hans Dedecker
0e84393ee2 dnsmasq: fix dnsmasq startup issue
Commit ecd954d530 installs specific interface triggers which rewrites the dnsmasq config
file and restarts dnsmasq if the network interface becomes active for which a trigger
has been installed.
In case no dhcp sections are specified or ignore is set to 1 dnsmasq will not be started
at startup which breaks DNS resolving.
Fix this by ditching the BOOT check in start_service and always start dnsmasq at startup.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-20 14:07:19 +02:00
Daniel Golle
969fe206bd brcm2708: Add wifi driver, firmware and NVRAM for RPi1
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-20 11:19:26 +02:00
Johann Neuhauser
dcc942e666 ath79: ar934x: use irq-ath79-intc driver and enable wmac
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
Johann Neuhauser
b8562f168b ath79: qca95xx: add new intc2, correct intc3 and add second pcie on qca9557
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
Johann Neuhauser
c7efc93509 ath79: fix irq-ath79-intc driver and add support for other ath79 SoCs
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
INAGAKI Hiroshi
189815462c ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:21 +02:00
INAGAKI Hiroshi
4645a6d318 ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:01 +02:00
Mathias Kresin
4bb6ee465e ramips: mt7621: fix wireless package selection
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-19 20:45:29 +02:00
Daniel Golle
512c57e7f3 ltq-vdsl-fw: add nonshared flag
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-19 17:57:06 +02:00
Evgeniy Didin
56f3aee531 arc770: bump kernel to 4.14
Currently arc770 is no more "source-only".
Lets update Linux kernel version from 4.9 to 4.14 for arc770.
config-4.14 was simply regenerated with "make kernel_menuconfig".

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
2018-06-19 14:32:47 +02:00