Commit graph

16699 commits

Author SHA1 Message Date
Christian Lamparter
ebaa82a2ca apm821xx: consolidate apm821xx device trees files
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.

Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-12 21:04:15 +01:00
Christian Lamparter
3a112113e7 apm821xx: add amcc, usb-otg-405ex devicetree definition
This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-12 21:04:15 +01:00
Eddi De Pieri
07bc0d6089 lantiq: fix pci issue if mem kernel parameter is used
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:

  mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M

By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.

The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.

This patch is a port of what legacy ifxmips_pci.c does.

Signed-off-by: Eddi De Pieri <eddi@depieri.net>
2016-11-12 21:04:15 +01:00
Matthias Schiffer
9cac5e8be0
ar71xx: generate region-coded factory images for TP-Link TL-WR841ND v11
The latest stock firmwares for US and EU regions have started checking the
region code.

Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-11 03:29:59 +01:00
Jo-Philipp Wich
998632bae2 arm64: boot-wrapper: add mirror checksum
Some builders have troubles cloning the boot-wrapper-aarch64.git repository so
provide a mirror checksum to allow downloading from sources.lede-project.org
instead.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-11-10 17:24:25 +01:00
Mathias Kresin
cc5c8f681e ramips: add TEW-691GR/TEW-692GR 2.4 GHz interface mac addresses
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.

The MAC address numbering of the TEW-691GR changes to the following
pattern:

  LAN:  AA:BB:CC:DD:EE:0C
  WIFI: AA:BB:CC:DD:EE:0D
  WAN:  AA:BB:CC:DD:EE:0F

The MAC address numbering of the TEW-692GR changes to the following
pattern:

  LAN:    AA:BB:CC:DD:EE:e4
  WAN:    AA:BB:CC:DD:EE:e5
  2.4GHz: AA:BB:CC:DD:EE:e7
  5 GHz:  AA:BB:CC:DD:EE:e8

Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.

Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:23:00 +01:00
Mathias Kresin
d8dd207ea6 ramips: use the ralink,mtd-eeprom device tree property
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.

Set the label and compatible string according to the the PCI binding
documentation.

Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.

Use the usual eeprom for the soc wmac of the Dovado Tiny AC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:22:59 +01:00
Mathias Kresin
21d8de78dc lantiq: drop ralink eeprom handling function
The eeprom handling function from the rt2x00 driver is used and this
code is obsolete.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Mathias Kresin
7fd5171a34 lantiq: use the device tree bindings from rt2x00 driver
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.

Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Mathias Kresin
13208e89d0 lantiq: fix VGV7519 and VGV7510KW22 mac addresses
The VGV7510KW22 stock firmware uses the following mac-addresses:

lan      (ifno 1): AA:BB:CC:DD:EE:60
wlan     (ifno 2): AA:BB:CC:DD:EE:61
atm0     (ifno 3): AA:BB:CC:DD:EE:62
atm1/wan (ifno 4): AA:BB:CC:DD:EE:63

The VGV7519 stock firmware uses the following mac-addresses:

lan:  AA:BB:CC:DD:EE:EF
wlan: AA:BB:CC:DD:EE:EF
wan:  AA:BB:CC:DD:EE:EE

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Mathias Kresin
e7c019c24d mac80211: rt2x00: fold patches
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-09 20:02:18 +01:00
Felix Fietkau
462a7c0e96 ar71xx: fix kernel relocate stub parallel build issue
Use per-kernel directory

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-08 11:51:27 +01:00
Rafał Miłecki
28955d9707 kernel: use upstreamed patch for BCM53573 support in bcm47xxsflash
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-11-08 11:36:39 +01:00
Christian Lamparter
b5638bb64e apm821xx: redo WAN green and yellow LEDs
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-08 11:17:10 +01:00
Pavel Kubelun
524d7a7cde ipq806x: fix pcie reset gpios
Fix perst-gpios property in accordance to the driver, so it stops spamming that it can't parse it.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-08 11:17:10 +01:00
Henryk Heisig
4ad68fa0a2 ar71xx: tl-wpa8630: Fix kernel lenght
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Roger Pueyo Centelles
5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00
BangLang Huang
bc4109845d ramips: fix Newifi D1 profile
the images were generated for the wrong flash size.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-11-08 11:17:10 +01:00
Rafał Miłecki
e2a65f4aa5 bgmac: backport small DMA fix
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-11-07 14:42:58 +01:00
Rafał Miłecki
4fae9db765 kernel: fix bgmac regression causing BCM47186B0 SoC hangs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-11-07 14:30:32 +01:00
Jo-Philipp Wich
95ac6906aa arm64: switch boot-wrapper to working repository
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-11-05 16:10:05 +01:00
Koen Vandeputte
347884b345 cns3xxx: fix UART resource overlap
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).

Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-11-05 10:18:27 +01:00
Felix Fietkau
3616666126 ipq806x: fix zyxel image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Felix Fietkau
fcf90318c5 ipq806x: clean up the kernel config and reduce kernel image size by disabling some unnecessary code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Felix Fietkau
fddd532612 ipq806x: fix a kconfig issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Christian Lamparter
8f2c2f94cf apm821xx: add back end-of-UBI marker for the WNDR4700 and MR24
The patch "build: drop UBI EOF marker from images by default"
(commit d27bce8d28) removed the
end-of-UBI marker. Without this marker, the boards will panic
during boot:

[    1.683458] ubi0: attaching mtd4
[    1.696181] ubi0 warning: scan_peb: valid VID header but corrupted EC header at PEB 31
[    1.704367] ubi0 error: scan_peb: bad image sequence number 549886691 in PEB 32, expected 184585623
[    1.713377] Erase counter header dump:
[    1.717110]  magic          0x55424923
[    1.720843]  version        1
[    1.723797]  ec             0
[    1.726752]  vid_hdr_offset 512
[    1.729880]  data_offset    2048
[    1.733094]  image_seq      549886691
[    1.736740]  hdr_crc        0x92ba8130
[    1.740472] erase counter header hexdump:
[    1.744493] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
[    1.751528] UBI error: cannot attach mtd4
[    1.755373] hctosys: unable to open rtc device (rtc0)
[    1.761130] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.768604] Please append a correct "root=" boot option; here are the available partitions:
[...]
[    1.856992] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.866519] Rebooting in 1 seconds..Auto calibration ---

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-04 11:11:34 +01:00
Mathias Kresin
3db1a5c8fa lantiq: use external pci clock on ARV7506PW11
Fixes a ralink wireless driver related kernel crash as soon as a lot of
data is tranfered via wireless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-03 19:00:28 +01:00
Mathias Kresin
112cf52d45 lantiq: cleanup dts files
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
  in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-03 19:00:28 +01:00
Pavel Kubelun
b2135f3ba5 ipq806x: update DT in accordance to new drivers And add some more DT nodes
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
681f28990d ipq806x: switch to generic cpufreq driver cpufreq-dt
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver

Also switching to ondemand frequency scaling as it is fixed now

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
a154a3d8be ipq806x: add opp patches for voltage scaling
Preparing for cpufreq driver switch to generic cpufreq-dt

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
8749fb7894 ipq806x: update clk-qcom patches
Preparing for cpufreq driver switch to generic cpufreq-dt

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
bf7166e545 ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Sven Schwermer
5511c1c7c1 ramips: Use MT7621 I2C driver for MT7628/MT7688
The i2c-ramips driver does not work for the MT7628/MT7688 SoCs, the
i2c-mt7621 driver does.

Signed-off-by: Sven Schwermer <sven.schwermer@arcor.de>
2016-11-03 08:27:20 +01:00
Cezary Jackiewicz
dafbc94f95 ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbport
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-11-03 08:21:32 +01:00
Andrew Yong
faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
Stijn Segers
2f2ea7b44c kernel: update kernel 4.4 to version 4.4.30
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.

Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Stijn Segers
eefe07ef4d ramips: add usb packages into DIR-860L B1 profile
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Yutang Jiang
15a14cf166 layerscape: add 64b/32b target for ls1012ardb device
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.

The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2016-10-31 17:00:10 +01:00
Yutang Jiang
c6c731fe31 layerscape: add 64b/32b target for ls1043ardb device
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.

LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.

64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.

All of 4.4 kernel patches porting from SDK release or upstream.

QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2016-10-31 17:00:10 +01:00
Henryk Heisig
a34f96d6cf ramips: Archer C50 cleanup
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>

Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-31 16:58:41 +01:00
Stefan Koch
7929ab60bf lantiq: add vpe/watchdog modules to kernel
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch
4552bf158c lantiq: vpe softdog
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)

Modified after cherry-pick:
obj in Makefile

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch
e0229a16b0 lantiq: added support for VPE1
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756

If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1

To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch
01ab5209c0 lantiq: modify vr9.dts to support vmmc
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)

Modified after cherry-pick:
compatible attribute

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:32 +01:00
Pavel Kubelun
8f7e58c0fe ipq806x: add reserved memory node in Netgear R7800
KERNEL BUG: BAD_PAGE_STATE in process appears here and there during intensive memory usage.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-31 16:48:04 +01:00
Rosen Penev
369884c2a1 ramips: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2016-10-31 16:41:26 +01:00
Henryk Heisig
0744b6a044 ipq806x: ArcherC2600: export usb power pins
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 16:40:54 +01:00
Henryk Heisig
dbf2feb2b3 ipq806x: ArcherC2600: devictree cleanup
add blank lines and use macros for GPIOs

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 16:40:28 +01:00
Paul Wassi
a569354481 kernel: update kernel 4.4 to version 4.4.28
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-10-31 16:33:53 +01:00
Hauke Mehrtens
76847c7fc9 kernel: deactivate CONFIG_QCOM_SPMI_TEMP_ALARM
This fixes the build of the ipq806x target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-10-31 14:35:30 +01:00
Chris Blake
53b43e65e7 ar71xx: Add net config for MR12 & MR16
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-31 12:52:56 +01:00
Christian Mehlis
7cb82d4b70 ar71xx: fix ethernet on wpj344 board
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
2016-10-31 12:52:56 +01:00
Rafał Miłecki
f20ba0f0d5 brcm47xx: image: use append-rootfs step for per-device rootfs support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-28 17:03:55 +02:00
Rafał Miłecki
027b2c5b83 brcm47xx: image: make TRX steps work with rootfs passed as $@
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-28 16:46:57 +02:00
Rafał Miłecki
8bd2167236 brcm47xx: image: make linksys-pattern-partition leave specific file
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-28 16:41:05 +02:00
Rafał Miłecki
c9fdb23345 apm821xx: fix USB LED trigger for WNDR4700
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-28 13:27:21 +02:00
Rafał Miłecki
bc6be3e953 brcm47xx: add support for per-device rootfs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-27 13:25:51 +02:00
Koen Vandeputte
d9c3727288 imx6: Add ds1672 RTC to kernel for working hctosys (Gateworks)
Fixes the same hctosys init issue as described in commit
5481ce9a11

The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-10-27 00:34:01 +02:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
6b0d279ca5 ar71xx: build relocate stub for generic and legacy images
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
e19427bd79 ar71xx/base-files: rename 09_fix-trx-header 09_fix-checksum
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
136319e72d kernel: mtdsplit: add support for WRGG images
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Chuanhong Guo
c5a7e2c2fb ar71xx: Ignore firmware building errors of UBNT and CyberTAN devices
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-10-26 14:07:20 +02:00
André Valentin
1465bebd74 ipq806x/nbg6817: add sysupgrade support
Add new way of flashing to mmc devices based on rootfs split with loop devices.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin
d8059e3a30 linux/mtd: add id for mx25u3235f needed by ZyXEL NBG6817
Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin
a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Stefan Koch
b760afa09a lantiq: danube fxs bugfix: changed compatible attribute of vmmc
This bugfix enables FXS support on dabube based devices.
Changed "compatible" attribute from "vmmc" to "vmmc-xway".
The vmmc driver uses "vmmc-xway".

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-26 12:37:46 +02:00
Paul Wassi
d2606107ab kirkwood: fix pogo_e02 LED name
The pogo_e02's dts file has its LEDs named "pogo_e02:(...)"
Fix the status-LED's name for this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:46 +02:00
Xuefu Lin
8312738806 ramips: fix PSG1218 LEDs
Signed-off-by: Xuefu Lin  <xuefulin@gmail.com>
2016-10-26 12:37:45 +02:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Paul Wassi
f6b5df44d9 kirkwood: remove redundant code in etc/board.d/02_network
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:45 +02:00
Chris Blake
fac018b25e ar71xx: Remove switch config for the MR12/MR16
These boards do not have a switch, so they should have never been added
to this file in the first place.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Chris Blake
28dd52b079 ar71xx: add mac partition to the MR12/MR16
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).

The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.

Once this partition is added to a device, you can set your MAC doing the
following:

mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot

Where 00:18:0a:33:44:55 is your MAC address.

This was tested, and confirmed working on both the MR12 and MR16.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Chris Blake
d8662ac3c6 ar71xx: Move MR12 & MR16 from legacy to generic
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.

Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:44 +02:00
Petr Štetiar
5481ce9a11 imx6: Add ds1307 RTC to kernel for working hctosys
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:

 [    2.427349] hctosys: unable to open rtc device (rtc0)
 [    3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
 [    8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2016-10-26 09:41:29 +02:00
Paul Wassi
5528573039 kirkwood: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 09:41:28 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Rafał Miłecki
93f9a9c71c kernel: backport MIPS's ioremap_cache from 4.5
It's needed by (updated) bcm47xxsflash driver.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 22:52:44 +02:00
Rafał Miłecki
13e6f7a75d brcm47xx: reorder older entries in image Makefile
Keep all entries sorted and replace tabs with spaces while at it.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 20:35:24 +02:00
Stijn Tintel
839b657a61 kernel: add fix for CVE-2016-5195
Add fix for CVE-2016-5195 to kernel 3.18 and 4.1.
Kernel 4.4 is already fixed since version 4.4.26 which was committed in
32c28a78f7.

Patches taken from Sasha Levin's linux-stable git tree:
http://git.kernel.org/cgit/linux/kernel/git/sashal/linux-stable.git/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Stijn Tintel
75e63c2494 kernel: update kernel 3.18 to version 3.18.43
Refresh patches for all targets supporting 3.18 and not marked broken.
Compile-tested on all targets using 3.18 and not marked broken.

Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Stijn Tintel
2fc3680dd0 kernel: update kernel 4.1 to version 4.1.34
Refresh patches for all targets supporting 4.1 and not marked broken.
Compile-tested on all targets using 4.1 and not marked broken.

Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Changes to generic/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch based
on a90ee92337.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Rafał Miłecki
06405df7a8 brcm47xx: bump kernel to 4.4
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).

This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)

After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
   loader), gzip compressed one, uncompressed one.

At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.

I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 17:22:23 +02:00
Rafał Miłecki
6e64a38b00 brcm47xx: build also TRX image for Linksys WRT300N V1
Linksys WRT300N V1 has pretty bugged CFE bootloader (it crashes in a lot
of situations) that doesn't accept .bin image.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 10:34:59 +02:00
Rafał Miłecki
337f219130 brcm47xx: open code Makefile entries for all devices
If we want to use some of new features like per device rootfs we will
need this to specify them there.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 10:33:33 +02:00
Imre Kaloz
3764caa934 mvebu: add support for the Linksys WRT3200ACM (Rango)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-24 08:45:06 +02:00
Imre Kaloz
2beab73fad mvebu: add missing status LEDs for Linksys WRT1200AC and WRT1900ACv2
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
2016-10-24 08:45:06 +02:00
Álvaro Fernández Rojas
920f922652 kernel: update kernel 4.4 to version 4.4.27
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-23 14:56:09 +02:00
Rafał Miłecki
3b26a5bb15 bcm53xx: include b43 in Tenda AC9 image
There is some (poor?) support for BCM43217 in b43.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-20 08:46:26 +02:00
Mathias Kresin
3c5a8a2cbc lantiq: enable cpu temp driver for all vr9 boards
Only present on v1.2 vr9 SoCs but the driver takes care to not load on
boards having a v1.1 SoC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Mathias Kresin
23e3314cad lantiq: fix thermal sensors driver
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.

Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.

Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.

Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Andreas Eberlein
eba84bee4c lantiq: Sanitize device tree files
The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes.

This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
[sanitize all device tree files]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:04 +02:00
Andreas Eberlein
72d12672de lantiq: Fix buttons for ARV752DPW
The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.

Both is fixed here.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
2016-10-19 19:06:15 +02:00
Mathias Kresin
fa14124616 lantiq: use new build code for DGN3500
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
1f7a03a706 lantiq: drop lzma-loader
It isn't used any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
17094e9e64 lantiq: rework VG3503J image
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.

To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:

  VR9 # run reset_uboot_config
  VR9 # reset
  VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The mac address is printed on the label at the bottom of the case.

The following steps are need to be done during first install:

  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.

Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.

A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Rafał Miłecki
ea7462ae07 bcm53xx: include usbport trigger for devices with USB
We don't have any code for enabling it automatically yet but it allows
adding entries manually to the /etc/config/system.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:28:52 +02:00