This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46281
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45635
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45634
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45633
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45524
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.
Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45523
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.
Signed-off-by: Sven Eckelmann <sven@open-mesh.org>
SVN-Revision: 45521
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.
The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45438
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
