Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
While at it, the following changes are introduced
- Rewrite the Makefile for better readability
- Make parallel builds possible
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This seems to occur when gettext-full is built on the host-side
and the autoreconf stuff re-generates some of the build files,
except for the po/Makefile.in.in
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Even though these fonts may not be installed, they seem to be
generated at build time.
Seems that the configure script re-generated from configure.ac
is a bit more annoying than it has to be.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reboot of: a0ea22ac43
Reverted: 3c52cbfa53
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Few minor code formatting style fixes, including:
- keep one board per line
- always use "|\" (for consistency)
- remove redundant double quotes and empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In order to prevent the impact of the merger of the company and the potential
rebase of the SDK repositories, migrate the u-boot source to github.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Based on the submission to the uboot-lantiq repo by Martin Blumenstingl.
Use the ddr_settings.h from the GPL tarball. The NAND boot optimized
one (with memory tuning enabled) doesn't work for the UART boot image.
Use the same mtd layout as the stock u-boot. Add add UBI support.
Use the leds to indicate boot status like it is done with the stock
u-boot. Switch on the red power led if kernel image can't be loaded.
Otherwise switch the green led on.
Make only the ramboot u-boot available. Only this image is required for
the first installation of LEDE.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The current uboot default config for the A13 SOM erroneously enables support
for the AXP209 power regulator IC which is not present on the board.
This superfluous support module sets an incorrect initial clock frequency and
confuses the kernel, ultimately leading to a boot failure later on.
Properly disable the PMIC support and enable the EHCI support by translating
the deprecated SYS_EXTRA_OPTIONS values into proper SUNXI_NO_PMIC and
USB_EHCI_HCD symbols respectively.
Also rename 002-add-olimex-a13-som.diff to 002-add-olimex-a13-som.patch and
refresh the remaining patches of the series while we're at it.
Reported-by: Mario Fischer <mario-fischer@web.de>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Fix the default value for the 'bootcmd' environment variable.
Therefore make the default bootcmd work for buildbot's images.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Fix metadata scan failure in the grub2 package by removing an unexpected
invisible space character and by adding back the missing SECTION variable
which was removed with d140648.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While enable zynq uboot:
CONFIG_PACKAGE_uboot-zynq-zc702
CONFIG_PACKAGE_uboot-zynq-zed
CONFIG_PACKAGE_uboot-zynq-zybo
make will arise dtc error:
./scripts/dtc-version.sh: line 17: dtc: command not found
./scripts/dtc-version.sh: line 18: dtc: command not found
*** Your dtc is too old, please upgrade to dtc 1.4 or newer
make[4]: *** [checkdtc] Error 1
Pass the kernel dtc to uboot for compile.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
