The mvebu image Makefile directly calls the padjffs2 utility, while there's an
generic make function to do just that. Switch to it
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SVN-Revision: 43968
Since the driver doesn't know anything about (M)STP
we just hard-set the ports to be enabled if they are
part of the VLAN.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43938
- eliminate MV_CPUPORT; not necessary since we define
the CPU port(s) via Device Tree
- add STU and expand VTU operations
- update register names to match those of 88E61xx rather than
mvswitch's 88E6060
- use more consistent formatting
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43937
3.3 produced *.dtb files in arch/arm/boot/ while 3.14 will produce those
in arch/arm/boot/dts/, adjust the image makefile accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43925
Most of the devices we support have between 16MiB and 32MiB of RAM
available.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43924
Initialize a Git repository in the SDK and use git reset / git clean
to rollback any SDK changes with "make clean" or "make dirclean".
This approach is more robust than nuking entire directory trees because
some parts of them might have been shipped with the original archive.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43904
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
This commit introduces a new option CONFIG_VERSION_FILENAMES which causes
OpenWrt to embed the version number in generated image files, SDK- and
ImageBuilder archives.
The option is enabled by default if CONFIG_VERSIONOPT is set.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43869
Move all AR8327/AR8337-specific driver code into a separate source file
ar8327.c and adjust patches so that ar8327.c is compiled if
CONFIG_AR8216_PHY is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43845
Move several structure definitions and #defines from ar8216.c
to ar8216.h and move AR8327/AR8337 header stuff into a new
header file ar8327.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43844
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
The following patches unfortunately didn't hit the kernel stable
branches yet, therefore cherrypicking them for OpenWRT here:
* bridge: fix netfilter/NF_BR_LOCAL_OUT for own, locally generated queries
* bridge: multicast: enable snooping on general queries only
* bridge: multicast: add sanity check for general query destination
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 43841
This will allow simple sysupgrade-s including simpler reverting to the
original firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43799
After the changes make ubinize.cfg optional in image.mk, ubifs
generation can now safely be enabled again.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43789
kernel lock debugging unveiled that we should not call
of_reset_control_get inside a clock's enable operation (see below)
move of_reset_control_* previously used in pllb_clk_enable to new
pllb_clk_prepare and pllb_clk_unprepare functions.
use a container to carry runtime information.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2742 lockdep_trace_alloc+0xb8/0xfc()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.26 #6
[<c001a6ac>] (unwind_backtrace) from [<c0016dec>] (show_stack+0x10/0x14)
[<c0016dec>] (show_stack) from [<c0194f68>] (dump_stack+0x7c/0x94)
[<c0194f68>] (dump_stack) from [<c0021b50>] (warn_slowpath_common+0x68/0x8c)
[<c0021b50>] (warn_slowpath_common) from [<c0021ba4>] (warn_slowpath_fmt+0x30/0x40)
[<c0021ba4>] (warn_slowpath_fmt) from [<c0061b30>] (lockdep_trace_alloc+0xb8/0xfc)
[<c0061b30>] (lockdep_trace_alloc) from [<c00cb740>] (kmem_cache_alloc+0x1c/0xf8)
[<c00cb740>] (kmem_cache_alloc) from [<c01d33c8>] (of_reset_control_get+0xe8/0x12c)
[<c01d33c8>] (of_reset_control_get) from [<c0269228>] (pllb_clk_enable+0x14/0xbc)
[<c0269228>] (pllb_clk_enable) from [<c0265738>] (__clk_enable+0x54/0xa0)
[<c0265738>] (__clk_enable) from [<c0265acc>] (clk_enable+0x18/0x2c)
[<c0265acc>] (clk_enable) from [<c04325f8>] (oxnas_pcie_probe+0x3b8/0x6a0)
[<c04325f8>] (oxnas_pcie_probe) from [<c01f2510>] (platform_drv_probe+0x18/0x48)
[<c01f2510>] (platform_drv_probe) from [<c01f1070>] (driver_probe_device+0xd8/0x24c)
[<c01f1070>] (driver_probe_device) from [<c01f1298>] (__driver_attach+0x70/0x94)
[<c01f1298>] (__driver_attach) from [<c01ef728>] (bus_for_each_dev+0x4c/0x98)
[<c01ef728>] (bus_for_each_dev) from [<c01f0818>] (bus_add_driver+0xcc/0x1e8)
[<c01f0818>] (bus_add_driver) from [<c01f169c>] (driver_register+0xa0/0xe8)
[<c01f169c>] (driver_register) from [<c01f2568>] (platform_driver_probe+0x20/0xa4)
[<c01f2568>] (platform_driver_probe) from [<c0013a3c>] (do_one_initcall+0x90/0x140)
[<c0013a3c>] (do_one_initcall) from [<c0421d38>] (kernel_init_freeable+0x1e4/0x2c0)
[<c0421d38>] (kernel_init_freeable) from [<c000c214>] (kernel_init+0x8/0x104)
[<c000c214>] (kernel_init) from [<c0008768>] (ret_from_fork+0x14/0x2c)
---[ end trace 5f17ed2f61e0683f ]---
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43787
accidentally #if was used instead of #ifdef, thus gcc warned
about CONFIG_ATA_LEDS being undefined...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43786
This is a 3.14.x backport of:
"mvneta: Fix TSO and checksum for non-acceleration vlan traffic"
Upstream commits:
817dbfa5d1bc276a72c1a577310382008e8aca0a
2d39d120781a5770573dc6ed672a5a562f541aea
Fixes vlan tagging on SoC interfaces for the WRT1900AC. Useful
when using mvsw6171 driver.
Signed-off-by: Mark Milburn <mark.a.milburn@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43781
safed one level of indention by using 'continue' instead of a
lengthy if-clause.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: use logic-AND instead of '?' operator when checking for hw bug 6320
SVN-Revision: 43768
- replaced // comments by /* comments */
- added line-breaks where needed
- fixed white-space according to kernel style
- fixed some obvious spelling mistakes in comments and printks
- removed some unneeded left-overs imported from vendor code-base
- replaced printk(...) by libata macros where possible
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43767
locking for 2nd port and hwraid was added from vendor's GPL code which
doesn't comply with current kernel coding style.
- moved all global variables into host_priv
- renamed locks
- sanetized acquire() and release() parameter list
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43766
and no longer compile-in ext4 filesystem now that sata_oxnas is
also built as a module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43765
Set defaults health led to a timer heartbeet (200/800)
and populate network for:
- GuruplugServerPlus
- SheevaPlug
- SheevaPlug with eSATA
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
SVN-Revision: 43752
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43750
When there is no device connected to the controller we should not start
the controller. This also changes between PCIe 1.0 and PCIe 2.0 speed
based on the device. This code is based on code from the new Broadcom
PCIe controller driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43748
This patch adds soc support for QCA9561 and TP9343.
TP9343 is a reduced version of QCA9561, which can be found in TP-LINK routers in China.
The qca956x_wmac has not yet been supported by ath9k.
tested on TL-WDR6500 and TL-WR882N v1 (Chinese version)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 43744
Remove read/write/rmw member functions from ar8xxx_priv
There seems to be no real benefit of the ar8xxx_priv member functions
read/write/rmw as one implementation exists for each of them only.
Especially ar8xxx_mii_rmw is assigned to priv->rmw first and then
mapped to ar8xxx_rmw.
Rename the ar8xxx_mii_.. functions to ar8xxx_.. and use them directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43742
Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43741
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43740
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
This will allow us to drop it in the future. This patch doesn't change
the final mtdpart.c, it remains the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43696
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
It moves firmware patch code behind an extra check on board_name.
Otherwise it will calculate firmware checksum for unaffected boards.
It also reduce boottime by a md5 calculation and removes error message
on boot if firmware not found.
SVN-Revision: 43679
Restoring the config for kernel 3.14 didn't contain that change already
made to config-3.18.
It is needed to make squashfs in the kernel match the compression settings
for ARCH=arm in the framework.
If set to ARMTHUMB, boot fails due to squashfs being unreadable if the
filesystem was generated for wth ARM BCJ filter.
in include/image.mk: BCJ_FILTER:=-Xbcj $(LINUX_KARCH)
Thus the ARM filter is used for all ARM targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43640
it should needs to depend on imx and mxs
also remove duplicate kmod definition from mxs target
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43627
The target au1000 has at least 2 different models, the
'InternetBox' and the 'MeshCube' which look very similar
from the kernel point of view but are totally different
devices which base on the same design. Populating /tmp/sysinfo
now. The 1st one has an issue which leads to a random
mac-address after each boot which is corrected now via
reading the bootloader-env. The real fix would be
converting to DTS, this is only a workaround now.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43626
This is required because it has to be called at very precise moment. See
comment in driver for details.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43611
similar to mv_sata, use nr-ports attribute from device tree.
import and adapt locking code from vendor GPL sources.
add dma controller handling, it may be used in future to avoid
full core resets similar to the vendor SDK's "progressive cleanup"
function.
this is still very dirty and aimed to first of all do things
quite exactly like the reference code. and it somehow works.
obviously there is lots of room for improvement :)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43598
sata_oxnas.c is obviously a refactored version of sata_ox820.c
which does contain this header.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43597
According to the vendor tarball, the TD-w8900GB's flash has 64k erase
block size, but CFE spans two blocks. So fixup the image offset
accordingly but keep block size at its default (64k).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: add commit message, add image offset, change nvram offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43572
This adds some updates to the NAND driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43546
This adds some updates to the PCIe driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43545
This brings ssb and bcma to wireless-testing tag master-2014-12-05
In addition it also adds the ARM-BCM5301X-Add-IRQs-to-Broadcom-s-bus-
axi-in-DTS-f.patch which adds the irq number in a way it is done in the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43544
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43539
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43538
This reverts commit c81ddddde5fd193802d511b42eb7b108aac17136 on
https://gitorious.org/openwrt-oxnas/openwrt-oxnas.git
which removed patches and config for 3.14.
[arm_introduce-dma-fiq-irq-broadcast patch was renamed to match 3.18]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43520
similar to what was observed on kirkwood this significantly accelerates
btrfs write operations.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43498
gpio-beeper module was added to the kernel recently.
Make use of it to drive the piezoelectric buzzer of the kd20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43496
This is a swconfig driver for the Marvell 88E6171 switch,
which is a 7-port GigE switch with two CPU ports and 64
802.1q VLANs.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43486
Factor out set_mirror_regs to ar8xxx_chip.
Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43468
Factor out info whether switch should be configured at probe stage
to ar8xxx_chip. Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43466
Patch to add the buildprofile for the GL-Init-6408A-v1 and the GL-Inet-6416A-v1
Both devices are identical, only difference is one comes with 8MB flash and
the other with 16MB flash
Official website: http://www.gl-inet.com/w/?page_id=241&lang=en
Comprehensive list of specs: https://revspace.nl/GL-Inet
Signed-off-by: Martijn Zilverschoon <martijn@friedzombie.com>
SVN-Revision: 43462
Add the required nodes for the interrupt controllers and register
them through DT when a DTB is present.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43457
Add irq-domain aware irqchip drivers for the irq controllers of bcm63xx
and switch to use them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43454
At least on my Iomega ix2-200 system, this makes btrfs writes about 30% faster.
Signed-off-by: Richard Kunze <richard.kunze@web.de>
SVN-Revision: 43434
