Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44995
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44986
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44982
Ensure gpio chips are always labeled the same; this allows simplifying
any arch setup gpio lookups.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44846
Now that we have converted all users of global variables to use
brcm63xx_board_name, we can savely convert the implicit call to detect
in brcm63xx.sh to a single, explicit call in preinit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44840
r37000 made button kmods loaded from generic code, so we don't use
it anymore for deciding to load them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44838
Instead of setting them up on invocation of brcm63xx_detect, set them
when calling diag.sh based.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44837
Board IDs are not unique, so in preparation for depricating them, always
use board_name for any (default) configuration decisions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44836
Use the device tree model property for detecting the board instead
of board id from nvram if present.
Since we can now directly detect the DVA-G3810BN, we can remove the
extra check for it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44834
Take full board name from devicetree, if present. Provide a method
for retrieving the board name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44833
Rename board_name to board_id to prepare for using board_name as a
proper name for the board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44832
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
The flag is experimental and requires toolchain support, which we don't
provide. Also neither target has an FPU so it becomes meaningless
without the FPU emulator enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44584
Linux commit d75b1ade567ffab ("net: less interrupt masking in NAPI")
chose the samantics of the napi poll return value, which caused napi to
not resume interrups/polling anymore.
Fix the return value to restore expected behaviour.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44576
Legacy probe passed the IRQSTAT registers instead of the IRQMASK
registers causing all register accesses to be offset by 16 bytes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44575
The driver expected data then dir, but both dts and legacy code passed
dir then data. Fix this by making the driver expect the registers in
ascending order, i.e. dir then data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44574
Now that all gpio users without named gpios use DT, we do not need
to fix the gpio controller bases anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44567
Register buttons and leds through DT for all available dts,
and remove them from the board files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
comment out spi-gpio and associated leds]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44566
Add a generic mmio gpio controller based driver and probe it
through device tree.
Use aliases for base calculation until we converted all users to
device tree or named gpios.
Convert bcm63xx_enet's ephy-reset gpio to use a named gpio.
While at it, remove the duplicate reset gpio defintion for livebox.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44565
