- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
The CPE210 was still described for the OEM upgrade as compatible,
even the wireless configuration isn't compatible anymore between
both series (2ghz and 5ghz).
Update the CPE210 image profile to use the new profile.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
The user benpicco in #openwrt reported that images are build which are
bigger that the available flash size.
He provided a proof of concept fix and gave permission to me to send it
for inclusion.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The RJ45 WAN port is used for xDSL as well as the IP101A.
The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.
Drop the ip101a-rst node. It can't be controlled and is not required
at all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The STP pinmux was initially added in assumption LAN2 led is driven by
it. It worked somehow because STP group and gphy0 led0 share the GPIO.
Do it the right way by adding the gphy0 led0 the gphy function.
According to the author, the SPI node is a copy & paste leftover. Which
makes sense since nothing is connected to the SPI bus on this device.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the brnboot partition layout as it is listed in the OpenWrt wiki
article for this board.
Configure the brnboot root selector for this device as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices.
The stp_out pinmux child node covers the same GPIOs as the already used
stp group.
The same applies to the gphy-leds_out pinmux node and the "gphy0
led1" as well as "gphy1 led0" groups.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.
Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
The query for ARMADA_THERMAL is stalling the kconfig process and as long as we
do not package it, simply disable the symbol.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
