Commit graph

1819 commits

Author SHA1 Message Date
Mathias Kresin
21abb7492c ramips: fix WHR-600D eeprom dt property
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.

Fixes: FS#691

Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
1b5ae14162 ramips: drop rt-n56u factory image
The factory image has an uImage header covering the entire image and
not only the kernel. The original uImage header which covers only the
kernel is appended to the end of the image.

During LEDE boot the uImage rootfs splitter skips the whole filesystem,
can't find a valid filesystem magic and panics.

The last known working version was OpenWrt 14.07, which simply kept on
searching for an uImage header if the first found didn't resulted into
a working rootfs. This behaviour is kind of error prone since it could
produce false positives.

Since the sysupgrade image works fine in combination with the tftp
recovery for doing the initial installation of LEDE, simply drop the
factory image.

Related: FS#462

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Hauke Mehrtens
c3778f2647 kernel: update kernel 4.4 to 4.4.59
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-04-02 12:48:00 +02:00
Hauke Mehrtens
b26e34214c kernel: update kernel 4.9 to 4.9.20
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-04-02 12:47:55 +02:00
John Crispin
0f4600c275 ramips: fix pcie irq mapping for mt7621 on v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-28 08:50:13 +02:00
Hauke Mehrtens
fb7ea71c15 kernel: update kernel 4.9 to 4.9.17
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 12:23:19 +02:00
Hauke Mehrtens
88b125e9a4 kernel: update kernel 4.4 to 4.4.56
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 12:23:12 +02:00
Mathias Kresin
c59469b908 ramips: fix Xiaomi MiWiFi Nano firmware partition size
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.

Fixes: FS#622

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
John Crispin
dce3b0057b ramips: fix mt7621 boot on v4.9
v4.9 CM code has a few bugs on this HW. Disable the GCR register access
during boot. This caused a cpu stall.

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-23 09:18:42 +01:00
Furong Xu
2fd1a3e912 ramips: clean kernel config symbol conflicts for MT7688 PWM
pwm-mediatek should be selected in Other Modules submenu, not default to yes.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-20 08:17:34 +01:00
Vaclav Svoboda
6b9c25e927 ramips: fix switch port mapping for ZBT-WE2026
This patch fixes switch port mapping for Zbtlink ZBT-WE2026.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-20 08:13:56 +01:00
Vaclav Svoboda
815cc2a69a ramips: add support for Zbtlink ZBT-WE2026
This patch adds support for the Zbtlink ZBT-WE2026.

Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M

Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-17 08:58:50 +01:00
Mathias Kresin
11eac705c5 ramips: sort mt7620 image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-12 09:28:19 +01:00
Joseph C. Lehner
de33a4cef0 ramips: add support for Netgear EX3700
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the device's web
interface or via nmrpflash.

Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Hanqing Wong
38bee61dab ramips: add support for Netgear R6220
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.

Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
  on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
  (login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
  example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Signed-off-by: Hanqing Wong <hquu@outlook.com>
2017-03-12 09:28:05 +01:00
Kristian Evensen
b11c51916c ramips: Improve Sanlinking D240 config
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.

* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.

v2->v3:
* Indentation error.

v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-03-11 08:36:52 +01:00
Furong Xu
a93a48328d ramips: kmod-sdhci-mt7620: switch dependence to kmod-mmc
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-11 08:19:37 +01:00
Jo-Philipp Wich
2543e986ad ramips: fix Linksys RE6500 switch port mapping
Properly map the internal switch ports to the proper LAN1..LAN4 labels.

Fixes #530.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-03-07 17:39:20 +01:00
Joseph C. Lehner
11356e4078 ramips: remove kmod-mt76* from EX2700 images
These modules are not needed by the EX2700, since it does not
have an external wifi chip (MT7620A is covered by rt2x00).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-01 22:29:57 +01:00
Furong Xu
b65718ae14 ramips: rename patch file suffix from .c to .patch
Signed-off-by: Furong Xu <xfr@outlook.com>
2017-03-01 22:29:57 +01:00
Francois Goudal
9b35815f0f ramips: add support for Afoundry EW-1200
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.

It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.

The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.

Signed-off-by: Francois Goudal <francois@goudal.net>
2017-03-01 22:29:50 +01:00
ZengFei Zhang
edae3479e6 ramips: add support for HiWiFi HC5962
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com

Short specification:

 - MT7621AT + MT7612EN + 7603EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+3 x 1000M Ethernet
 - 1x USB 2.0 port. 1x USB 3.0 port.
 - reset button
 - UART pad on PCB (JP3: TX, RX, GND, 3.3V)

Flash instruction:

1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
   $ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
   $ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1

Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
2017-02-28 23:46:02 +01:00
Wang JiaWei
d48cc5e044 ramips: add support for HiWiFi HC5661A
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.

- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)

The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.

0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"

To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.

sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin

SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.

Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
2017-02-27 11:39:31 +01:00
Joseph C. Lehner
df36b5e1b3 ramips: include only kmod-mt76-core in EX2700 image
This patch frees up flash space on the EX2700, by
removing unused mt76 drivers and firmware.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-02-26 10:26:50 +01:00
Furong Xu
f885edef5a ramips: fix the number of uarts for MT7688
Same as MT7621 and MT7628, MT7688 allows up to 3 uarts

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:37 +01:00
Furong Xu
00343e18f2 ramips: fix PWM pin mux conflict in dtsi
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict

[    0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[    0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[    0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0  on device rt2880-pinmux
[    0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back

Keep PWM disabled.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:09 +01:00
Hauke Mehrtens
236840eb47 kernel: update kernel 4.9 to version 4.9.10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-16 00:46:23 +01:00
Daniel Golle
d57223259b ramips: replace remaining instances of ralink, port-map
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-02-15 09:12:40 +01:00
John Crispin
6cb0372d42 ramips: fix mt7621 ethernet support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:12:00 +01:00
Giuseppe Lippolis
35c60d18c5 ramips: export slic IRQ line in dwr-512
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-15 07:45:54 +01:00
Felix Fietkau
f5977c0c0a ramips: revert faulty 4.4 config change from 9c24227090
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:47:21 +01:00
Furong Xu
a9fdb35740 ramips: Clean duplicated status property for Omega2 WMAC in dtsi
At the tail of dtsi, wmac is enabled twice, clean the first one

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-14 12:19:56 +01:00
Giuseppe Lippolis
85766c8d70 ramips: fixed sms led polarity into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-14 12:19:35 +01:00
Thibaut VARENE
157353c210 ramips: WN3000RPv3: do not setup switch
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-14 12:19:12 +01:00
John Crispin
9c24227090 ramips: add v4.9 support
NAND support is missing

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-14 12:17:52 +01:00
Giuseppe Lippolis
ec0f20212e ramips: added image size into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-13 10:24:32 +01:00
Chuanhong Guo
634328c0de ramips: correct switch configuration for Newifi D1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-02-13 10:24:32 +01:00
Claudio Leite
290ca2ba46 ramips: fix AR670W partition alignment
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.

Signed-off-by: Claudio Leite <leitec@gmail.com>
2017-02-09 09:14:45 +01:00
Stijn Tintel
d2c4041f02 kernel: update kernel 4.4 to version 4.4.47
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.

Runtime-tested on ar71xx, octeon, ramips and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-02-06 03:23:06 +01:00
Kristian Evensen
bb7068f26c ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-02-05 22:23:28 +01:00
Joseph C. Lehner
7d00cfe9bb build: centralize fakeroot code
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.

Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Mathias Kresin
c1eae7a7b8 ramips: fix Airlink AR725W device title
Gemtek is the ODM but the board was sold by Airlink101.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Mathias Kresin
1ba7fa652c ramips: fix Airlink AR725W factory image build
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.

Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 13:46:48 +01:00
Giuseppe Lippolis
f9f636b94e rt5350: added pcm interface in .dtsi
Added the missing audio pcm interface in the .dtsi file for the rt5350
device. The update has been verified from the data get from the datasheet
and is very similar to the mt7620a.dtsi

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-03 05:10:13 +01:00
Mathias Kresin
a0888ecbaf generic: rtl8366rb: fix compatible string
Use a vendor prefix as it has to be for all not core driver. Update the
compatible string in the device tree files accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:46:03 +01:00
Mathias Kresin
2c4d81310f ramips: fix Sercomm NA930 compatible string
The Sercomm NA930 is not a mt7620a evaluation board and shouldn't use
the eval board compatible string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:46:03 +01:00
Mathias Kresin
2281f9929b ramips: remove Planex CS-QR10 sound device tree node
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:45:55 +01:00
Mathias Kresin
05b1fcc70b ramips: cleanup SPI flash device tree properties usage
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.

Remove the linux,modalias property. It is obsolete since kernel 4.4.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-02 22:48:54 +01:00
Tobias Wolf
bf2f09c005 ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to F5D8235 V1 (rt288x)
This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and
configures the F5D8235 V1 target to use append-dtb for kernel creation
instead of OWRTDTB.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-02 00:13:49 +01:00
Tobias Wolf
4f86692953 ramips: Introduce CONFIG_MIPS_APPENDED_RAW_DTB to arch/mips/ralink
This commit introduces CONFIG_MIPS_APPENDED_RAW_DTB as an alternative to
OWRTDTB. Both solutions can be used concurrently until all board
configurations have been changed.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-02 00:13:49 +01:00