Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Board IDs are not unique, so in preparation for depricating them, always
use board_name for any (default) configuration decisions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44836
Rename board_name to board_id to prepare for using board_name as a
proper name for the board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44832
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.
Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41944
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41588
This adds support for Comtrend WAP-5813n.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41421
Only netboot tested, so no images or now.
GbE ports are only working in FE mode, and leds do not work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39679
Completely untested except for booting from network; wan port
only works in 10/HD, lan1 only in 100/FD.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39678
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds userspace support for Sagemcom F@st 2704 router.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4215/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39672
Actually this board is the very same as the rta770bw,
where the additional 'b' within the name just
indicates 'Annex B'. The ADSL Modem itself is able
to handle both, Annex A as well as Annex B -
the loaded firmware makes the only difference
SVN-Revision: 35500
Switch to using the B53 switch driver where appropriate.
Use a non-tagged default config where it isn't confirmed to be
working.
Remove the switch configuration in preinit as the switch will now
be configured by the driver to use port isolation to prevent leakage
between lan and wan.
While at it, also provide a switch config for Neufbox 6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35307
