Commit graph

16 commits

Author SHA1 Message Date
Hauke Mehrtens
c371e6de02 brcm47xx: activate high mem for mips74k in the config
It is still not working.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42054
2014-08-07 20:22:00 +00:00
Hauke Mehrtens
5996160a66 brcm47xx: add CONFIG_LEDS_GPIO_REGISTER
CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41488
2014-07-02 22:07:46 +00:00
Hauke Mehrtens
c2992ee273 brcm47xx: add new led and button support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39252
2014-01-12 18:55:25 +00:00
Hauke Mehrtens
961d5b4453 brcm47xx: b44: This updates the phylib patches to the version send upstream
This uses a fixed phy instead of a dummy one.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39166
2013-12-26 23:27:52 +00:00
Hauke Mehrtens
36197755dc brcm47xx: deactivate early printk support
This breaks some devices where the serial console is not at port 0 but
somewhere else.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39060
2013-12-15 19:19:16 +00:00
Hauke Mehrtens
cbbfc5f1e6 brcm47xx: config: set CONFIG_HZ=100 and CONFIG_IP_ROUTE_VERBOSE
This sets both values to the OpenWrt default values. There is no reason
to use some brcm47xx specific values here.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38978
2013-12-01 17:34:27 +00:00
Hauke Mehrtens
3fb7e8b851 brcm47xx: add vectored interrupts
This adds support for vectored interrupts in this SoC.
This is supported by the 74K cpus.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38975
2013-12-01 16:37:58 +00:00
Hauke Mehrtens
68081fc1c8 brcm47xx: register ADM6996L switch
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.

This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38699
2013-11-09 19:29:46 +00:00
Hauke Mehrtens
f023c09699 brcm47xx: activate ARP daemon support
This just add some bytes to the kernel and is activated on other targets.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38388
2013-10-13 22:46:18 +00:00
Hauke Mehrtens
b201818044 brcm47xx: update early printk patches
Early printk was disabled because it caused hangs on some devices, the
old patches were using the CFE console now we use the normal serial
console, it is at a constant address.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38309
2013-10-06 23:55:35 +00:00
Hauke Mehrtens
c75a970337 kernel: b53: add Register Access Bridge Registers (SRAB) interface
The SRAB interface is used on BCM4707 and BCM5301X SoCs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 38198
2013-09-25 21:44:28 +00:00
Hauke Mehrtens
c78e4fb220 brcm47xx: Add support for Huawei E970
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.

The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.

It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.

Tested and works:  3G wan,  wlan+LED,  VLAN config,  failsafe using reset
button,   image to be used for upgrade from OEM firmware's web interface

Link to the wiki page I've created:  <http://wiki.openwrt.org/toh/huawei/e970>

Issue:

* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
  reset during kernel decompress.

Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>

SVN-Revision: 38011
2013-09-16 21:09:10 +00:00
Hauke Mehrtens
b4880b34ef brcm47xx: add default config for new kernel config option
SVN-Revision: 37958
2013-09-12 22:04:55 +00:00
Jonas Gorski
b1b4e7db13 kernel: move CONFIG_NET_IP_TUNNEL to generic
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 37465
2013-07-19 22:58:01 +00:00
Hauke Mehrtens
f8d55e7541 brcm47xx: use b53 phy driver for the switch in kernel 3.10
This makes it possible to use swconfig to controll the switch.

This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.

SVN-Revision: 37304
2013-07-14 14:11:17 +00:00
Hauke Mehrtens
a5c0ad6354 brcm47xx: add initial support for kernel 3.10
SVN-Revision: 37287
2013-07-14 13:44:45 +00:00