Commit graph

42956 commits

Author SHA1 Message Date
Bernhard Frauendienst
480bf28273 ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
    WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
    Diag red, Movie Engine blue, USB green)

It is already supported by the ar71xx target.

For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>

Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
  - via TFTP rescue
  - via factory image
    - on firmware v1.77 (28-05-2012)
    - on pro firmware v24SP2 r30356 (26-03-2018)
  - via sysupgrade from ar71xx
    (wlan devices don't work because of new names)
  - via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)

Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-09-10 09:35:07 +02:00
Bernhard Frauendienst
3370e10495 kernel: add driver for virtual mtd_concat devices
Some systems require multiple flash chips to be concatenated and read as
a single mtd device. The ar71xx target provides custom code to create
such mtdconcat devices. When porting devices to ath79, however, there is
no way to create such devices from within the device tree.

This commit adds a driver for creating virtual mtd-concat devices to the
ath79 target. Nodes must have a compatible = "virtual,mtd-concat" line,
and define a list of devices to concat in the 'devices' property,
for example:

flash {
	compatible = "virtual,mtd-concat";

	devices = <&flash0 &flash1>;
};

The driver is added to the very end of the mtd Makefile to increase the
likelyhood of all child devices already being loaded at the time of
probing, preventing unnecessary deferred probes which might in turn
cause other problems (like failure to load MAC addresses from art because
the partitions are not loaded yet).

Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-09-10 09:35:07 +02:00
INAGAKI Hiroshi
7768f11534 ath79: add support for ELECOM WRC-300GHBK2-I
ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4 GHz wifi
  - SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 4x keys(connected to GPIO: 3x)
- UART header on PCB
  - TX, GND, RX, Vcc from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Boot the WRC-300GHBK2-I normaly and connect the computer to its
LAN port
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, execute "mtd erase firmware" to
erase stock firmware and execute sysupgrade with squashfs-sysupgrade
image for WRC-300GHBK2-I
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-09-10 09:30:28 +02:00
INAGAKI Hiroshi
7a67b437e7 firmware-utils: mkedimaximg: add "big-endianness mode" option
In addition to the default little-endianness format, I added a mode
so that we can generate firmware with big-endianness format.

example: ELECOM WRC-300GHBK2-I (QCA9563)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-09-10 09:29:39 +02:00
Martin Schiller
628eb271dc kernel: backport i2c-gpio working over slow can_sleep GPIOs
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-09-10 09:28:55 +02:00
Martin Schiller
bc24f0ad2b kernel: backport rtc ds1308 support to 4.9
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-09-10 09:19:44 +02:00
Eneas U de Queiroz
0317fc3658 libpcap: patch to add limits.h to pcap-usb-linux.c
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is an upstream-applied patch that fixes 'PATH_MAX' and 'NAME_MAX'
undeclared when compiling on musl with CONFIG_PCAP_HAS_USB.

[aafa351] pcap-usb-linux.c: add missing limits.h for musl systems.

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2018-09-10 09:15:26 +02:00
Rosen Penev
6a2ee91267 mvebu: Replace RTC initialization patch with upstreamed version
While we're at it, rename the patches to their proper git format-patch
name.

Tested on a Turris Omnia.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-09-10 09:11:31 +02:00
Rosen Penev
a9aa25c8b6 usbutils: Update usb.ids to 0.315
Referencing the version instead of revision should fix uscan.

Tested on Turria Omnia.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-09-10 09:10:20 +02:00
Christian Lamparter
745dee11ac ath79: add support for WD My Net Wi-Fi Range Extender
This patch ports over support for the device from ar71xx.

SOC:	AR7370 (Wasp - AR9344 rev2 0001974c)
RAM:	Winbond W9725G6KB-25 32MiB
FLASH:	Winbond 25Q64FVSIG 8MiB
WLAN:	AR9380 Dual-Band 802.11abgn 3x3:3
INPUT:	WPS, RESET button (hardware on/off toggle button)
LED:    Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high)
Serial: Header Next to the winbond flash chip (labeld JP1)
	Pinout is GND - NC - RX - TX - 3V3 (JP1)
	The Serial setting is 115200-8-N-1.

- Installation via uboot's upgrade command
  0. attach serial cable
  1. interrupt uboot and enter "upgrade code.bin" into
      the u-boot prompt
	ar7240> upgrade code.bin

  2. rename openwrt...sysupgrade.bin to code.bin on PC
  3. run a tftp-client on the PC
	 (shell)$ tftp 192.168.1.230
	 binary
	 put code.bin
  4. wait for the device to finish

	[...]
	Copy buff to Flash from 0x9f040000 length 0x79f000
	Copy to Flash... write addr: 9f040000
	done

  5.  enter "go" in the u-boot prompt
	ar7240> go

- TFTP ramdisk image boot from the uboot prompt
  (tftp server defaults to serverip 192.168.1.254)
	=> tftpboot 81000000 initramfs.bin
	=> bootm

Tested and working:
	- LEDs
	- Buttons
	- Ethernet
	- Wi-Fi
	- OpenWRT sysupgrade

For flashing and debricking information see:
<https://openwrt.org/toh/wd/rext>

Users coming from ar71xx can use sysupgrade too. But I highly
advise to no save the old configuration and start from a clean
state.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-09-10 09:07:41 +02:00
Christian Lamparter
cd9c2492c1 ath79: port cybertan_part from ar71xx
This patch ports the cybertan_part code from ar71xx and converts the
driver to a DT-supported mtd parser. As a result, it will no longer
add the u-boot, nvram and art partitions, which were never part of
the special Cybertan header.

Instead these partitions have to be specified in the DT, which has the
upside of making it possible to add properties (i.e.: read-only), labels
and references to these important partitions.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-09-10 09:07:11 +02:00
Rafał Miłecki
ffa80bf5a7 mac80211: add iw command wrapper with error logging
Currently it's close to impossible to tell what part of mac80211 setup
went wrong. Errors logged into system log look like this:
radio0 (6155): command failed: No error information (-524)
radio0 (6155): command failed: Not supported (-95)
radio0 (6155): command failed: I/O error (-5)
radio0 (6155): command failed: Too many open files in system (-23)

With this commit change it's getting clear:
command failed: No error information (-524)
Failed command: iw dev wlan0 del
command failed: Not supported (-95)
Failed command: iw phy phy0 set antenna_gain 0
command failed: I/O error (-5)
Failed command: iw phy phy0 set distance 0
command failed: Too many open files in system (-23)
Failed command: iw phy phy0 interface add wlan0 type __ap

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-09-10 09:03:09 +02:00
Rosen Penev
f78e07ad2a hostapd: Fix compile with OpenSSL 1.1.0 + no deprecated APIs
Patch was accepted upsteam:

https://w1.fi/cgit/hostap/commit/?id=373c796948599a509bad71695b5b72eef003f661

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-09-10 09:01:37 +02:00
Luis Araneda
192838e018 zynq: rename zedboard with correct manufacturer
The board is made by Avnet, so rename it accordingly as
upstream has done it

Also move the device to maintain alphabetic order

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:56:16 +02:00
Luis Araneda
412763c812 zynq: add sdcard image support
Implement the generation of sdcard images with ext4 or
squashfs + f2fs overlay, but only enable the latter
automatically

Additionally, add mkf2fs and e2fsprogs to default packages
to manipulate ext4 and f2fs filesystems

Finally, disable the automatic generation of initramfs
and rootfs.tar.gz images, as they are no longer required
(they can still be selected in menuconfig)

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:55:39 +02:00
Luis Araneda
d6501467e7 zynq: enable kernel overlay and f2fs support
Select configs to enable build-in F2FS support
and use the overlayfs provided by generic config

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:55:20 +02:00
Luis Araneda
1ee9294609 zynq: remove bootargs from kernel config
Use options from generic instead of target-specific,
as the bootargs are now passed by the bootloader
and can be device-specific

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:55:02 +02:00
Luis Araneda
e2a4d14aaa uboot-zynq: use a file to modify the default environment
Follow the strategy of other targets and create a
default environment file, uEnv.txt, to configure the
behavior of U-Boot.
For now, use it to pass bootargs to the kernel

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:54:41 +02:00
Luis Araneda
306a60fcfe uboot-zynq: copy U-Boot images to STAGING_DIR
Create a directory inside STAGING_DIR and copy U-Boot
output images, so they can be used later when creating the
sdcard image

Additionally, like others targets, override the default
install method to avoid copying the images to bin directory

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:54:25 +02:00
Luis Araneda
e62df3dd8b uboot-zynq: automatically select the appropriate variant
Select the U-Boot variant automatically based on the
current selected device, and hide the package from
menuconfig

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:54:00 +02:00
Luis Araneda
5d2b702590 uboot-zynq: remove ZC706 board
The board was added when creating the target, but the
corresponding device was never defined inside the target

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-09-10 08:53:28 +02:00
Hans Dedecker
43d4b8e89e dnsmasq: bump to dnsmasq 2.80test6
Refresh patches

Changes since latest bump:

af3bd07 Man page typo.
d682099 Picky changes to 47b45b2967c931fed3c89a2e6a8df9f9183a5789
47b45b2 Fix lengths of interface names
2b38e38 Minor improvements in lease-tools
282eab7 Mark die function as never returning
c346f61 Handle ANY queries in context of da8b6517decdac593e7ce24bde2824dd841725c8
03212e5 Manpage typo.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-09-09 22:02:45 +02:00
Daniel Engberg
791a3a22ad tools/cmake: Update to 3.12.2
Update CMake to 3.12.2

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-09-09 21:38:20 +02:00
Daniel Engberg
9cfa5f2cec curl: Update to 7.61.1
Update curl to 7.61.1

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-09-09 21:38:10 +02:00
Yousong Zhou
9e58c20ec9 scripts/ipkg-build: quash error messages when conffiles.resolved is empty
When Package/xx/conffiles only contains directories that are empty at
package time, conffiles.resolved will be missing and the following
error messages will appear in the build log.

	/home/yousong/git-repo/openwrt/openwrt/scripts/ipkg-build -c -o 0 -g 0 /home/yousong/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/linux-malta_be/openvswitch-2.10.0/ipkg-mips_24kc/openvswitch-common /home/yousong/git-repo/openwrt/openwrt/bin/packages/mips_24kc/packages
	mv: cannot stat 'CONTROL/conffiles.resolved': No such file or directory
	chmod: cannot access 'CONTROL/conffiles': No such file or directory

It will not break the ipkg-build process.  The change is merely cosmetic
to not cause confusion when reading logs

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2018-09-09 01:21:01 +00:00
Yousong Zhou
204081670b scripts/metadata.pm: avoid adding dup names in provides list
The need arises from building Open vSwitch kernel datapath modules, e.g.

 - kmod-openvswitch from Linux upstream
 - kmod-openvswitch-intree from openvswitch source code

where both provides virtual package "kmod-openvswitch" for userspace
packages to select and depend on

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2018-09-09 01:21:01 +00:00
pacien
ef01c1d308 odhcp6c: add client fqdn and reconfigure options
Allowing DHCPV6_CLIENT_FQDN and DHCPV6_ACCEPT_RECONFIGURE to be turned off.
Defaulting to false, former behavior remains unchanged.

Signed-off-by: pacien <pacien.trangirard@pacien.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
2018-09-08 21:36:30 +02:00
Koen Vandeputte
42f158314e ar71xx: fix switch probing on kernel 4.14
The bump to 4.14 changed the way mdio probes behind switches.

While the board_info is added to the list, the code that actually inserted
the list info into the phydev structure was missing.

This resulted in non-working ethernet ports.

Re-add it to fix switch probing.
This mimics the exact behaviour as it was in kernel 4.9.

Before:

[    1.066007] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.073409] Atheros AR8216/AR8236/AR8316: probe of ag71xx-mdio.0:00 failed with error -22
[    1.102455] libphy: ag71xx_mdio: probed
[    1.737938] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Generic PHY]
[    1.747994] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.377642] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.429938] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII

After:

[   11.163357] libphy: Fixed MDIO Bus: probed
[   11.319898] libphy: ag71xx_mdio: probed
[   11.360844] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[   12.447398] libphy: ag71xx_mdio: probed
[   13.077402] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[   13.088989] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[   13.717716] ag71xx-mdio.1: Found an AR934X built-in switch
[   13.769990] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Koen Vandeputte
2253524023 gdb: bump to 8.2
*** Changes in GDB 8.2

 Support for the following target has been added:

    RiscV ELF (riscv*-*-elf)

 Support for following targets and native configurations has been removed:

    m88k running OpenBSD (m88*-*-openbsd*)
    SH-5/SH64 ELF (sh64-*-elf*)
    SH-5/SH64 (sh*)
    SH-5/SH64 running GNU/Linux (sh*-*-linux*)
    SH-5/SH64 running OpenBSD (sh*-*-openbsd*)

 Various Python API enhancements
 Aarch64/Linux enhancements:

    SVE support.
    Hardware watchpoints improvements for entities stored at unaligned addresses.
        New "c" response to disable the pager for the rest of the current command.
        C expressions can now use _Alignof, and C++ expressions can now use alignof.
        Improved flexibility for loading symbol files.
        The 'info proc' command nows works on running processes on FreeBSD systems as well as core files created on FreeBSD systems.
        A new --enable-codesign=CERT configure option to automatically codesign GDB after build (useful on MacOS X).

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Koen Vandeputte
c24d02d154 toolchain/gdb: bump to 8.2
*** Changes in GDB 8.2

 Support for the following target has been added:

    RiscV ELF (riscv*-*-elf)

 Support for following targets and native configurations has been removed:

    m88k running OpenBSD (m88*-*-openbsd*)
    SH-5/SH64 ELF (sh64-*-elf*)
    SH-5/SH64 (sh*)
    SH-5/SH64 running GNU/Linux (sh*-*-linux*)
    SH-5/SH64 running OpenBSD (sh*-*-openbsd*)

 Various Python API enhancements
 Aarch64/Linux enhancements:

    SVE support.
    Hardware watchpoints improvements for entities stored at unaligned addresses.
        New "c" response to disable the pager for the rest of the current command.
        C expressions can now use _Alignof, and C++ expressions can now use alignof.
        Improved flexibility for loading symbol files.
        The 'info proc' command nows works on running processes on FreeBSD systems as well as core files created on FreeBSD systems.
        A new --enable-codesign=CERT configure option to automatically codesign GDB after build (useful on MacOS X).

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Koen Vandeputte
77024a9d95 mac80211: backport upstream fixes
Backport most significant upstream fixes (excl. hwsim fixes)
Refreshed all patches.

Contains important fixes for CSA (Channel Switch Announcement)
and A-MSDU frames.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Koen Vandeputte
079871983c kernel: bump 4.14 to 4.14.68
Refreshed all patches.

Remove upstream accepted:
- 330-Revert-MIPS-BCM47XX-Enable-74K-Core-ExternalSync-for.patch

Altered:
- 303-v4.16-netfilter-nf_tables-remove-multihook-chains-and-fami.patch
- 308-mips32r2_tune.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Koen Vandeputte
752ee31ad2 kernel: bump 4.9 to 4.9.125
Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Koen Vandeputte
b4bd6c2c95 kernel: bump 3.18 to 3.18.121
Refreshed all patches.

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-07 17:21:24 +02:00
Carlo Nel
6bbb220255 ramips: add support for TP-Link TL-MR3020 v3
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.

This PR is based on the work of @meyergru[1], with his permission.

Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet

Flash instruction:

The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3

Signed-off-by: Carlo Nel <carlojnel@gmail.com>
2018-09-06 21:36:42 +02:00
Matt Merhar
9c26def64a ath79: fix unaligned access panic in ag71xx_mdio_probe
Without "syscon" being present in an ag71xx ethernet DT node's
compatible property, a panic occurs at boot during probe citing
"Unhandled kernel unaligned access".

With this modification, the panic no longer occurs and instead the probe
simply fails, allowing the boot process to continue.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-09-06 21:35:53 +02:00
Matt Merhar
b672550b32 ath79: add syscon compatible property to ar7100 ethernet nodes
This adds "syscon" to the compatible properties for the eth0/eth1 nodes
in ar7100.dtsi.

Without this, a kernel panic is encountered on boot with some ar7100
boards. This for some reason wasn't an issue for the WNDR3800, which
uses a Realtek switch chipset, but the panic was encountered on the
RouterStation Pro (using an AR8216 switch) and some other boards that
haven't yet been merged.

The panic message mentions an unaligned access and happens in
ag71xx_mdio_probe in drivers/net/ethernet/atheros/ag71xx/ag71xx_mdio.c.

Even if the unaligned access is fixed, the ag71xx_mdio probe still fails
without the "syscon" property.

This was already being worked around in
ar7161_ubnt_routerstation-pro.dts by overriding the compatible property,
so this commit removes that as well.

All of the other ath79 .dtsi already have this property, so no changes
are needed elsewhere.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-09-06 21:35:53 +02:00
Mathias Kresin
287b7aa583 ramips: drop obsolete sd card driver code
The pinmux for all SoCs using this driver is now set via the pinmux. It
makes this code obsolete.

Some of the code targeting the mt76x8 SoCs is still required. The sd
card pins share the pads with the EPHY. These pads need to be switched
to digital mode if the pins are used for sd cards.

The eMMC 8-bit mode has to be enabled via pinmux instead of a kernel
option. The uart2 group need to be set to function "sdxc d5 d4", pwm1
to "sdxc d6" and pwm0 to "sdxc d7" to do so. It can't be done by as
part of a default pinmux, as it would break the normal operation of
uart2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
563a5b5f94 ramips: add mt7620/1 sdhci pinmux
Set the pins to the required mode via the pinmux driver. It allows to
get rid of the pinmux related code in the sd card driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
a14097e8e0 ramips: fix mt7620a ND/SD pins pinmuxes
Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually
exclusive and for most of the boards not even used as GPIOs.

If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still
GPIOs (#45 and #46).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
2cc7980dcb ramips: reference node by label
Reference the HC5661A sdhci node by label instead of by the full path.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
1d08951628 ramips: add rt3352 SPI_CS1 pinmux
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin but it is already used in the SoC dtsi.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Henrique de Moraes Holschuh
ca1b347691 dnsmasq: allow dnsmasq variants to be included in image
The dnsmasq variants should provide dnsmasq, otherwise it is impossible
to include them in the image.

This change allows one to have CONFIG_PACKAGE_dnsmasq=m and
CONFIG_PACKAGE_dnsmasq-full=y, e.g. because you want DNSSEC support, or
IPSETs suport on your 3000-devices fleet ;-)

Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
2018-09-06 17:57:59 +02:00
Hans Dedecker
3d377f4375 dnsmasq: bump to dnsmasq v2.80test5
Refresh patches
Remove 240-ubus patch as upstream accepted.
Add uci option ubus which allows to enable/disable ubus support (enabled
by default)

Upstream commits since last bump:

da8b651 Implement --address=/example.com/#
c5db8f9 Tidy 7f876b64c22b2b18412e2e3d8506ee33e42db7c
974a6d0 Add --caa-record
b758b67 Improve logging of RRs from --dns-rr.
9bafdc6 Tidy up file parsing code.
97f876b Properly deal with unaligned addresses in DHCPv6 packets.
cbfbd17 Fix broken DNSSEC records in previous.
b6f926f Don't return NXDOMAIN to empty non-terminals.
c822620 Add --dhcp-name-match
397c050 Handle case of --auth-zone but no --auth-server.
1682d15 Add missing EDNS0 section. EDNS0 section missing in replies to EDNS0-containing queries where answer generated from --local=/<domain>/
dd33e98 Fix crash parsing a --synth-domain with no prefix. Problem introduced in 2.79/6b2b564ac34cb3c862f168e6b1457f9f0b9ca69c
c16d966 Add copyright to src/metrics.h
1dfed16 Remove C99 only code.
6f835ed Format fixes - ubus.c
9d6fd17 dnsmasq.c fix OPT_UBUS option usage
8c1b6a5 New metrics and ubus files.
8dcdb33 Add --enable-ubus option.
aba8bbb Add collection of metrics
caf4d57 Add OpenWRT ubus patch

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-09-06 15:48:13 +02:00
Stijn Tintel
067e2f5f1d strace: fix build on aarch64
As of version 4.21, strace enforces mpers by default. The current
implementation of aarch64 compat in strace assumes it's identical to
ARMv7 EABI and therefore tries to enable m32 personality support. As
there is no -m32 support on aarch64, this causes the build to fail.

Restore previous strace behavior to fix build on aarch64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Karl Palsson <karlp@tweak.net.au>
2018-09-05 23:49:15 +02:00
Hans Dedecker
ecc3165cbc odhcpd: bump to git HEAD (detect broken hostnames)
881f66b odhcpd: detect broken hostnames
3e17fd9 config: fix odhcpd_attrs array size

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-09-05 11:04:19 +02:00
Felix Fietkau
36c6ba3735 imx6: use BUILD_DEVICES in uboot-imx6 for mx6cuboxi
Fixes build with the default profile

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-05 10:00:01 +02:00
Felix Fietkau
b9f926e151 imx6: rename Generic profile to Default, fixes u-boot image build issue
u-boot.mk checks for the Default profile to build images for all targets.
This brings the target default profile in sync with other targets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-05 10:00:01 +02:00
Jason A. Donenfeld
4ccbe7de6c wireguard: bump to 0.0.20180904
* Kconfig: use new-style help marker
* global: run through clang-format
* uapi: reformat
* global: satisfy check_patch.pl errors
* global: prefer sizeof(*pointer) when possible
* global: always find OOM unlikely

Tons of style cleanups.

* crypto: use unaligned helpers

We now avoid unaligned accesses for generic users of the crypto API.

* crypto: import zinc

More style cleanups and a rearrangement of the crypto routines to fit how this
is going to work upstream. This required some fairly big changes to our build
system, so there may be some build errors we'll have to address in subsequent
snapshots.

* compat: rng_is_initialized made it into 4.19

We therefore don't need it in the compat layer anymore.

* curve25519-hacl64: use formally verified C for comparisons

The previous code had been proved in Z3, but this new code from upstream
KreMLin is directly generated from the F*, which is preferable. The
assembly generated is identical.

* curve25519-x86_64: let the compiler decide when/how to load constants

Small performance boost.

* curve25519-arm: reformat
* curve25519-arm: cleanups from lkml
* curve25519-arm: add spaces after commas
* curve25519-arm: use ordinary prolog and epilogue
* curve25519-arm: do not waste 32 bytes of stack
* curve25519-arm: prefix immediates with #

This incorporates ASM nits from upstream review.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2018-09-05 08:52:36 +02:00
Matthias Schiffer
b452af23a8
mpc85xx: add migration script for TP-Link TL-WDR4900 v1 WLAN PCI paths
PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9;
migrate config so existing wifi-iface definitions don't break.

This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-09-04 21:27:27 +02:00