ath79: add support for ELECOM WRC-300GHBK2-I

ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4 GHz wifi
  - SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 4x keys(connected to GPIO: 3x)
- UART header on PCB
  - TX, GND, RX, Vcc from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Boot the WRC-300GHBK2-I normaly and connect the computer to its
LAN port
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, execute "mtd erase firmware" to
erase stock firmware and execute sysupgrade with squashfs-sysupgrade
image for WRC-300GHBK2-I
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi 2018-09-10 09:30:28 +02:00 committed by John Crispin
parent 7a67b437e7
commit 7768f11534
3 changed files with 202 additions and 0 deletions

View file

@ -40,6 +40,10 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
;;
elecom,wrc-300ghbk2-i)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
;;
embeddedwireless,dorin)
ucidef_add_switch "switch0" \
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
@ -177,6 +181,9 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_text "caldata" 65440)
wan_mac=$(mtd_get_mac_text "caldata" 65460)
;;
elecom,wrc-300ghbk2-i)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
;;
iodata,etg3-r)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" -1)

View file

@ -0,0 +1,160 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca956x.dtsi"
/ {
model = "ELECOM WRC-300GHBK2-I";
compatible = "elecom,wrc-300ghbk2-i", "qca,qca9563";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
};
leds {
compatible = "gpio-leds";
power: power {
label = "wrc-300ghbk2-i:white:power";
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
wlan2g {
label = "wrc-300ghbk2-i:white:wlan2g";
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "phy0tpt";
};
wps {
label = "wrc-300ghbk2-i:red:wps";
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
button_wps {
label = "wps";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
ap {
label = "ap";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
read-only;
};
partition@50000 {
label = "nvram";
reg = <0x050000 0x020000>;
read-only;
};
partition@70000 {
label = "firmware";
reg = <0x070000 0x770000>;
};
partition@7e0000 {
label = "hwconfig";
reg = <0x7e0000 0x010000>;
read-only;
};
ART: partition@7f0000 {
label = "ART";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
phy-mode = "sgmii";
qca,ar8327-initvals = <
0x04 0x00000080 /* PORT0 PAD MODE CTRL */
0x50 0xcf37cf37 /* LED_CTRL0 */
0x54 0x00000000 /* LED_CTRL1 */
0x58 0x00000000 /* LED_CTRL2 */
0x5c 0x03ffff00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&ART 0x1002>;
mtd-mac-address-increment = <(-1)>;
phy-mode = "sgmii";
phy-handle = <&phy0>;
};
&uart {
status = "okay";
};
&wmac {
status = "okay";
mtd-cal-data = <&ART 0x1000>;
};

View file

@ -17,6 +17,31 @@ define Build/addpattern
-mv "$@.new" "$@"
endef
define Build/elecom-header
$(eval fw_size=$(word 1,$(1)))
$(eval edimax_model=$(word 2,$(1)))
$(eval product=$(word 3,$(1)))
$(eval factory_bin=$(word 4,$(1)))
if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(fw_size)" ]; then \
$(CP) $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) $(factory_bin); \
$(STAGING_DIR_HOST)/bin/mkedimaximg \
-b -s CSYS -m $(edimax_model) \
-f 0x70000 -S 0x01100000 \
-i $(factory_bin) -o $(factory_bin).new; \
mv $(factory_bin).new $(factory_bin); \
( \
echo -n -e "ELECOM\x00\x00$(product)" | dd bs=40 count=1 conv=sync; \
echo -n "0.00" | dd bs=16 count=1 conv=sync; \
dd if=$(factory_bin); \
) > $(factory_bin).new; \
mv $(factory_bin).new $(factory_bin); \
$(CP) $(factory_bin) $(BIN_DIR)/; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Device/avm_fritz300e
ATH_SOC := ar7242
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
@ -62,6 +87,16 @@ define Device/dlink_dir-825-b1
endef
TARGET_DEVICES += dlink_dir-825-b1
define Device/elecom_wrc-300ghbk2-i
ATH_SOC := qca9563
DEVICE_TITLE := ELECOM WRC-300GHBK2-I
IMAGE_SIZE := 7616k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
elecom-header 7798706 RN51 WRC-300GHBK2-I \
$(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin
endef
TARGET_DEVICES += elecom_wrc-300ghbk2-i
define Device/embeddedwireless_dorin
ATH_SOC := ar9331
DEVICE_TITLE := Embedded Wireless Dorin