Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
rewrite it
* add interrupt error status support for debug. default disable it.
because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use
Signed-off-by: Michael Lee <igvtee@gmail.com>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
verify this function. on rt305x it will copy more data. on mt7621
only two channels can works at the same time. these two chips
maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.
Signed-off-by: Michael Lee <igvtee@gmail.com>
This patch allows configuring ports to be disabled in the device tree; this
saves power, since disabling ports here actually disables power to ethernet
PHYs.
Line 444 enables all ethernet ports, so line 487 is getting zero ports to be
disabled, except for port 5 in SoCs where this is not implemented as it will
be sticky disabled in register POC0. Because of this, the code will still read
the switch configuration and OR it to the device tree setting.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49290
Line 444 is actually enabling all switch ports by setting the disable bits
to 0. This needs to be done because the bootloader sets all ports to disabled
by default (which is the case for at least one router based on RT5350).
So, this patch fixes the comment in line 443.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49289
The FCT2 esw register should be set to 0x2500C to have "unknown IPv6
multicast" packets broadcasted to every port, instead of dropped.
The previous value only let those packets go through ports 1 and 3.
"Unknown IPv6 multicast" packets include packets needed by ICMPv6 echo
requests addressed to well-known addresses, such as ff02::1 (MAC address
is 33:33:00:00:00:01 in this case).
Please note that by default ICMPv6 echo requests to ff02::1 are not replied
to by the router because of ip6tables considering those packets to be invalid.
But this is another bug/patch. ;)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49287
Makes the patches apply again by fixing the white space broken patch.
This problem was introduced in r49212.
Closes#22248 and #22259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49221
Misc fixes for LinkIt 7688 board:
- Copy the right wireless firmware for the mt7688
- Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4.
- Remove SPI_DEV from linux config which otherwise causes a massive warning
- Add wmac to LINKIT7688.dts so wireless works
Signed-off-by: Adam Kent <adam@semicircular.net>
SVN-Revision: 49130
