This adds support for Aerohive AP-121 access point.
Specification:
- SoC: Atheros AR9344-BC2A at 560MHz
- WiFi 1: 2.4GHz Atheros AR9340? - SoC
- WiFi 2: 5.0GHz Atheros AR9382-AL1A
- Memory: 128MB from 2x Nanya NT5TU32M16DG-AC
- SPI: 1MB Macronix MX25L8006E
- NAND: 128MB Hynix H27U1G8F2BTR-BC
- Ethernet: Atheros AR8035-A
- USB: 1x 2.0
- TPM: Atmel SC3204
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, download and flash LEDE factory image over tftp:
dhcp;
setenv serverip tftp-server-ip;
tftpboot 0x81000000 lede-ar71xx-nand-hiveap-121-squashfs-factory.bin;
nand erase 0x800000 0x800000;
nand write 0x81000000 0x800000 0x800000;
reset;
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[minor text changes in commit subject and description, fixed
alphabetical order in etc/diag.sh, use only model name in lib/ar71xx.sh,
fixed code style issues in mach-hiveap-121.c, ubinized factory image]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan
This commit adds basic support for Rambutan development kit
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 1x USB2.0 host socket + 1x USB2.0 pins on 2.54mm header
Flash instructions:
Stock firmware is OpenWrt, so use:
sysupgrade -n /tmp/lede-ar71xx-nand-rambutan-squashfs-sysupgrade.tar
or upgarde from GUI (don't save config)
Use factory image to flash from U-Boot:
tftpboot 80060000 lede-ar71xx-nand-rambutan-squashfs-factory.ubi
nand erase.part ubi
nand write 80060000 ubi ${filesize}
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[split support in uboot-envtools package into a separate commit,
fixed alphabetical order in lib/preinit/05_set_iface_mac_ar71xx]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds the build option for the new UniFi AC Mesh.
It is a direct hardware copy from the AC Lite.
- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 1 1000M - POE
- Wireless:
2.4G: QCA9563
5G: UniFi Chip, QCA988X compatible
Thanks to Frank Dietz for testing.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[wrapped too long lines in mach-ubnt-unifiac.c]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add rut5xx GPIO PIN selection to om-package startup script.
Testet on a RUT500 device, the timeout value of the hardware watchdog
is about 280 sec.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
[split into two commits, bump PKG_RELEASE]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This fixes switch port mapping for: TL-WR841N/ND v8, TL-MR3420 v2 and
TL-WR941N/ND v5. All of them share the same Atheros ap123 reference
design.
The order of switch ports (shown in "swconfig dev eth1 show") is CPU,
LAN 4, LAN 1, LAN 2, LAN 3.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[included 2 more devices]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
93abe6f config: fix invalid hoplimit in RA message
2ae08d1 config: fix invalid retranstime in RA message
0005cb4 config: fix invalid reachabletime in RA message
5683dd2 config: limit ra_mtu to 65535
f8d40a5 router: fix interface mtu read error
f8f4b87 config: limit ra_retranstime to 60000
a2d8bf6 dhcpv4: display two hex digits per octet in syslog
a9e9bc4 config: make RA retransTime configurable via uci
2cb6b48 config: make RA reachableTime configurable via uci
e4504db config: make RA curHopLimit configurable via uci
9dd5316 config: make RA mtu configurable via UCI
29cb2ff config: fix dhcpv4 server being started
0ef74ec ndp.c: add switch/case fallthrough comments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
these two devices have a Sata led for each sata port.
These leds must be controlled separately by a special
sata led trigger already used in oxnas target.
Both these devices have a single USB led, and to keep
consistent behaviour with the Sata leds that show
sata activity, this led uses usb-host trigger
to show usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some files (e.g. /etc/dropbear) need to be owned by root. Add cpio
option to ensure that.
Other image types (at least targz and squashfs) already have this.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Gracefully handle cases where the to-be-created wireless interface already
exists on the system which might commonly happen with non-multi-SSID capable
wireless drivers.
This fixes commit 8301e61365 which caused
previously ignored "Too many open files in system (-23)" errors to fail the
wireless setup procedure.
With the updated approach we'll still try recreating the vif after one
second if the first attempt to do so failed with ENFILE but we will now
consider the operation successfull if a second attempt still yields ENFILE
with the requested ifname already existing on the system.
Fixes FS#664, FS#704.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refer to LINUX_KARCH instead of ARCH when bundling DTS files in the image
builder tarball.
While we're at it, also dereference symbolic links when copying as some
kernel architectures contain symbolic links in their DTS directories.
This fixes aarch64 imagebuilders such as brcm2708/bcm2710 ones in particular
as the kernel refers to "aarch64" as "arm64" internally.
Ref: https://forum.lede-project.org/t/lede-image-builder-problem/3680
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Add device tree files for Solidrun ClearFog Base board.
We also need to backport some improvements for Armada
388 MicroSoM.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
The conventional model is now known as the "Clearfog Pro".
We keep the old armada-388-clearfog.dts file for compatibility reasons.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
libthread-db is a package that can be configured for external
toolchains, so let's have the script probe for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some external toolchains may be configured to enable OpenMP. Provide a
package for these libraries which can be used by other packages.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the necessary changes to CMakeLists.txt to search zlib.h. Fixes
build issues with external toolchains that don't have STAGING_DIR in the
default search path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Toolchain built for ARCv1 (read for ARC700 cores) by default has
disabled atomic ops (-mno-atomic). When we build Linux kernel for ARC770
which has LL/SC instructions and thus may handle normally atomic ops we
explicitly add "-matomic" in CFLAGS. But since user-space perf utility has
no way to extract CPU config options from Kconfig/defconfig it uses
compiler default settings.
In case of ARCv2 (read ARC HS38) atomics are enabled by default and so
perf builds perfectly fine thus reenabling perf for ARC HS38 (actually
for non-ARC700 targets).
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
When running "make {config|defconfig|oldconfig}" with symlinked .config
(e.g. to env/.config) it renames symlink to .config.old, creates new
.config file, and writes the updated configuration into it.
This breaks the desired workflow when changes in the configuration can
be checked using "scripts/env diff" and commited using "scripts/env
save". Since the env/.config file is not updated.
The things become even worse when working with feeds, since feeds script
quite often silently invokes "make {oldconfig|defconfig}" and breaks the
symlink.
Fix this issue by exporting KCONFIG_OVERWRITECONFIG=1, which forces
mconf to overwrite the .config content, instead of renaming it and
creating a new file. This variable is set only if .config is a symlink,
otherwise the variable is not exported and the old behaviour is
preserved.
This change uses the same behaviour as "make menucofig", which has
already been fixed in commit 5bf98b1acc.
Also make a tiny cosmetic update to the "make menuconfig" target code
layout to make it look like other config handling targets.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Add missing include of ramips.sh in order to import the missing
ramips_board_name() procedure.
Fixes FS#774.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Specification:
- SoC: MediaTek MT7620A (580 MHz)
- RAM: 64 MiB (Winbond W9751G6JB-25)
- Flash: 16 MiB (Spansion S25FL128SAIF00)
- LAN: x4 100M
- WAN: x1 100M
- Others: USB 2.0, reset button, wps button and 9 LEDs
Issues:
- 5 GHz band is not functional (missing driver support)
Installation:
Asus windows recovery tool:
- install the Asus firmware restoration utility
- unplug the router, hold the reset button while powering it on
- release when the power LED flashes slowly
- specify a static IP on your computer:
IP address: 192.168.1.75;
Subnet mask 255.255.255.0
- Start the Asus firmware restoration utility, specify the sysupgrade
image, and press upload
TFTP Recovery method:
- set computer to a static ip, 192.168.1.75
- connect computer to the LAN 1 port of the router
- hold the reset button while powering on the router for a few seconds
- send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
tftp> quit
Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
This device exactly same as NBG-419N but with USB port and USB Led.
Specification:
- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0
Installation via serial console (57600 8N1) from TFTP server
- rename the firmware to something shorter, for example
"sysupgrade.bin" (max. 32 chars)
- copy firmware TFTP server's directory
- when you power on device, and see U-Boot log, immediatly push "2"
once.
- You will see this message:
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?
- Push "y", and enter: device IP, then TFTP server's IP, and then
image firmware file name.
The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).
Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds the interface-name option for each dhcp config
in /etc/config/dhcp.
With the interface_name option users can define a DNS name for each dhcp section
that will be resolved by dnsmasq with the underlaying interface address.
For example:
config dhcp 'lan'
option interface 'lan'
...
list interface_name 'home.lan'
...
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The
correct DTS for this device is "ar1004g".
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
It has been shown that the Fritz boxes have the correct mac address set
in the wireless calibration data/eeeprom. Use this mac address as base
for the ethernet and xdsl interface increment/decrement the address to
match the values stored in the tffs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
commit 89878f60f4 x86: lift kernel minimum CPU requirement to Pentium MMX
caused kconfig havoc. Fix this and make sure PAE is enabled even on legacy
CPUs as the minimum required CPU has been Pentium MMX for a while now and
hence PAE is supported even on the x86_legacy target.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
