This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
The u-boot on Open Mesh devices checks the whole transfered image against a
md5sum. This is stored inside the option filemd5sum inside the
fwupgrade.cfg. The bootloader will not check it when this setting is
missing and could therefore write invalid images to the flash.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46925
The GPIO pins for "POE passthrough" of Ubiquiti Nanostation models are the
following:
* Ubiquiti Nanostation M XM: Pin 8
* Ubiquiti Nanostation M XW: Pin 2
The previous definition of the pins was mixed up between XM and XW model.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46922
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
Thanks to Sylwester Petela for testing my patch (successfully on an
ADSL connection) and for pointing out some configuration mistakes.
Others (including me) have also successfully tested this extensively
on VDSL connections.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46920
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
DWC2 driver has config symbol CONFIG_USB_DWC2_DEBUG_PERIODIC which
should be defined for the module build.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46916
Add AR9 DTS definition to be recognized by the DWC2 driver.
The same driver parameters can be mostly used except that some boards
seem to erroneously report OTG HNP/SRP capability of the USB HCD.
Forcing the HNP/SRP off allows these boards to work with the DWC2 as well.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46915
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.
Here are the DTS definitions which make it compatible with the DWC2
driver.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46914
Based on the ltq-hcd driver the AR9 USB can be initialized the same way
as the VR9 platform. Use the same initialization bits for both
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46913
Force opkg to store the downloaded repository indizes into the cache
directory as well, this way the IB can be used in an offline setting
once all required files have been cached.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46912
Expose the "lists_dir" configuration file option as command line
switch so that we can override it for the Image Builder environment.
Also add a more standard PKG_MAINTAINER variable while touching
the Makefile.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46911
- Add patch for optional static linking preference
- Prefer static linking on Linux systems
- Enable verbose compiler messages when building with V=c
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46908
Force a static build of the xz utilities in order to avoid the dependency on a
shared liblzma.so which might collide with the distro version.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46907
To make the lzma-loader build with binutils 2.25.1 it is needed to
remove the .MIPS.abiflags section otherwise I get the following compile
error:
mips-openwrt-linux-musl-objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S loader loader.bin
mips-openwrt-linux-musl-objcopy: Warning: Writing section `.text' to huge (ie negative) file offset 0xffffffff80a00000.
mips-openwrt-linux-musl-objcopy:loader.bin[.text]: File truncated
This should close#20487.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46893
This moves arch patches affecting many DTS files. Thanks to this change
we can put some ready-to-mainline patches at 300-319 and simplify
backporting process.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46889
The driver only supports wl18xx-fw-4.bin and does not support the old
firmware wl18xx-fw-3.bin and more.
The wl18xx-conf.bin file was removed upstream it does not fit all
devices any more, see this on how to generate one:
http://processors.wiki.ti.com/index.php/Open_Source_Wireless_Connectivity_wlconf
If someone has a config file for the common platforms with the wifi nic
OpenWrt uses please send a patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46887
- should fix issue: https://forum.openwrt.org/viewtopic.php?id=57315
- enable support of more USB stick with rt28xx chipsets
- experimental: USB-IDs not in vendor linux driver
- experimental: "exact chipset is unknown"
- experimental: "enabling these devices may or may not work"
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46882
