On the Linksys WRT54GSv1, the adm6996 switch driver and the
gpio_button_hotplug module both claim GPIO 6, which is connected to the
Reset button. When the switch driver's request wins, the Reset button
cannot work. This makes it impossible to enter failsafe mode without a
serial console.
Stop requesting the "adm_rc" GPIO in the switch driver, since it is not
used anywhere.
Fixes FS#792.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0
Known issues:
- Unable to detect 53115 switch attached to MDIO. Not supported
- No support for the cable port
More info on the device and the research can be found at:
http://www.actiontec.com/212.html
Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)
Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The pinmux register is at relative offset 0x8, not 0xc. Fixes hang
when trying to modify pins >= 32.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a
typo in 02_network, fix it by removing the stray paren.
Reported-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.
Fixes FS#852
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As it turned out, some of new MediaTek based TP-Link devices use value
from field at 0x3c offset in version 3 of TP-Link header to specify
"Additional Hardware Version".
Value from this field is validated during regular (GUI) firmware upgrade
on devices like TL-WR840N v4 or TL-WR841N v13. If it's zero (based on
some tests, it seems that firmware will accept anything != 0), errors
like below are printed on console and upgrade fails:
[ rsl_sys_updateFirmware ] 2137: Firmware Additional HardwareVersion
check failed
[ rdp_updateFirmware ] 345: perror:4506
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)
QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.
Flash instruction:
Use "factory" image directly in vendor GUI.
Recovery method:
1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server.
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset
This commit is based on GitHub PR#1112
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Federico Cappon <dududede371@gmail.com>
Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.
Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.
Fixes FS#835
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Migrate Arduino Yun from legacy to generic building code.
Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.
To use the new partitioning, you need to update your U-Boot env in
advance:
setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv
Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.
Signed-off-by: Leon M. George <leon@georgemail.eu>
The kernel configs for all targets should have the version in the
filename, for clearness and consistency across all targets.
It is also expected by the update_kernel.sh script.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport upstream dnsmasq patch fixing DNS failover when first servers
returns REFUSED in strict mode; fixes issue FS#841.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add a uci option to set the new max auth tries paramater in dropbear.
Set the default to 3, as 10 seems excessive.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for '-T n' for a run-time specification for maximum number
of authentication attempts where 'n' is between 1 and compile time
option MAX_AUTH_TRIES.
A default number of tries can be specified at compile time using
'DEFAULT_AUTH_TRIES' which itself defaults to MAX_AUTH_TRIES for
backwards compatibility.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
RADIUS protocol could be used not only for authentication but for
accounting too. Accounting could be configured for any type of networks.
However there is no way to configure NAS Identifier for non-WPA
networks without this patch.
Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
[cleanup commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
I did not port the regulator and power patches from Stefan Wahren
because I talked to him and he told me that work on this is currently
stalled. And since AFAIK nothing depends on these patches, leaving them
out seems reasonable.
I build minimum default configurations and run-tested them on both
I2SE Duckbill devices and Olimex Olinuxino Maxi boards successfully [1].
[1] Tested:
- debug uart is working
- boot without any obvious kernel problem
- network is coming up and data transfer is possible
- Olinuxino: USB detects a plugged-in pen drive
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
[refreshed config and patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In preparation for bumping mxs target to 4.9, disable a bunch of configuration
symbols that provoked config prompts.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
ath10k-firmware: add qca9888 firmware
the firmware files for qca9888 were previously not packaged. add the meta
information for doing so.
Signed-off-by: John Crispin <john@phrozen.org>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The sum variable need to be initialised, otherwise it will points to
random stack memory and a bogus image checksum might be calculated.
While at it, fix the segfault in case the product region code isn't
specified and enable compiler warnings which had revealed all the code
issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't start ping-check of address in DHCP discover if there already
exists a lease for the address. It has been reported under some
circumstances android and netbooted windows devices can reply to
ICMP pings if they have a lease and thus block the allocation of
the IP address the device already has during boot.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Expose "term_timeout" parameter in procd.sh to allow init scripts to
request a longer termination timeout.
This is required to fix FS#859 in a later commit.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Adjust default permissions and ownership of /dev/tty* nodes from
0600/root:root to 0660/root:tty in order to support granting
unprivileged user access when needed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is needed for an upcoming change to the hotplug default rules which
will cause /dev/tty* nodes to get assigned to the "tty" group in order
to support unprivileged user access when needed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes some security issues (no remote exploits), and introduces
some changes. See release notes for details:
https://tls.mbed.org/tech-updates/releases/mbedtls-2.5.1-2.1.8-and-1.3.20-released
* Fixes an unlimited overread of heap-based buffers in mbedtls_ssl_read()
* Adds exponent blinding to RSA private operations
* Wipes stack buffers in RSA private key operations (rsa_rsaes_pkcs1_v15_decrypt(), rsa_rsaes_oaep_decrypt())
* Removes SHA-1 and RIPEMD-160 from the default hash algorithms for certificate verification.
* Fixes offset in FALLBACK_SCSV parsing that caused TLS server to fail to detect it sometimes.
* Tighten parsing of RSA PKCS#1 v1.5 signatures, to avoid a potential Bleichenbacher/BERserk-style attack.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
