This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
SVN-Revision: 45726
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
SVN-Revision: 45630
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45553
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 44620
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44359
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.
Signed-off-by: Vincent Wiemann <me@bibbl.com>
SVN-Revision: 44165
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 42897
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 42552
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41767
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
The RB2011UiAS is almost exactly the same as the RB2011UAS, which is
already supported. Hardware-wise, it adds a passive power injector on
Eth10. Software-wise, Routerboot passes a different board name on the
kernel command line. Hence the need for a patch.
Not yet working:
* touchscreen: doesn't work on RB2011UAS either. The touchscreen itself
seems to be driven by an ADS7843-compatible IC, but figuring out which
GPIO pins it's connected to is work for the future.
* control of power injector: remains off. Probably also GPIO-controlled.
Signed-off-by: Soren Harward <stharward@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5841/
[juhosg: rename and refresh the kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41617
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
WAN and LAN are swapped the wrong way around. This patch fixes that by adding the 951Ui-2HnD to ar71xx.sh and the relevant entry in 02_network.
This patch also defines the ACT LED as the status LED in diag.sh.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41255
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40969
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40500
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40473
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40471
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 40400
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg: use correct board name in uci-defaults/02_network]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 40033
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
- use the Archer C7 specific LED setup instead of adding
identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39636
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39373
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39078
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39064
There was no way to determine a working config, because
the switch (ar8337) was not working previously.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4470/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38953
Small update to uci_defaults/01_leds, to support the usb led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38947
Patch to add the user space support for the TL-WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38814
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
- move WiFi MAC address setup to the firmware hotplug file,
- use the official MAC address for the 2.4GHz as well,
- remove uci-defaults.sh modifications,
- update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38812
Patch to add user space support for the TL-WA750RE/WA850RE range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38718
Enable the wlan2g led in the default configuration of dir-825-c1.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4079/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38106
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38105
The goal is to set the WAN MAC address to the one on the
sticker on the bottom of the unit. Currently it is not
used at all. But some users expect the WAN interface to
have the MAC address that is written on the sticker.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38091
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36579
Accessing the AR8xxx switches via the name of the
attached ethernet device is not possible since
r35560. Change the uci-defaults script to use
switchX names in switch configurations.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35561
Based on the following patch:
http://patchwork.openwrt.org/patch/3043/
[juhosg: add uci-defaults/network support]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34780
It should be implemmented in a cleaner way.
This reverts the following commits:
[ar71xx] dir-825-b1: Fix wholeflash images
[ar71xx] dir825b1: Add image for DIR-825-B1 that uses the whole flash"
SVN-Revision: 33459
This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.
[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 33344
An improved LED support for Buffalo WZR-HP-AG300H.
There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.
[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 33294
For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33224
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32932
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32931
On TP-Link TL-WR741ND version 4, the WLAN LED must be configured to work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 31461
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.
To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router
Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]
SVN-Revision: 31208
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
SVN-Revision: 29973
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
SVN-Revision: 29972
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29912
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
I noticed most of /etc/defconfig was replaced by /etc/uci-defaults, which is
indeed much nicer. So I moved over ubootenv from having a defconfig-entry to
also be generated from uci-defaults.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28971