Commit graph

43123 commits

Author SHA1 Message Date
Romain MARIADASSOU
02494fa35c
Add support for TL-WA801ND v4
This add support for TP-Link TL-WA801ND v4 (same as TL-WA801ND v3) :

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: 650 MHz
- Flash-Chip: Winbond W25Q32BVSIG
- Flash size: 4096 KiB
- RAM: 32 MiB
- Wireless No1: SoC-integrated: QCA9533 2.4GHz 802.11bgn

Flash instructions:

1) To flash the image, rename the file
   openwrt-ar71xx-generic-tl-wa801nd-v4-squashfs-factory.bin
   to firmware.bin
2) Connect your device to the LAN port, then upload the firmware
   through web interface. It will try to download the image and
   flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-12-07 21:46:45 +01:00
Daniel F. Dickinson
32bc733796 ath79: dts: Use PowerCloud CAP324 bicolor status LED
PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files /
base files support using both colours to better inform user of state
and to better match stock firmware, so use green power to indicate
normal operation.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-06 20:26:57 +01:00
INAGAKI Hiroshi
3358cae523 ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.

WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.

There is no eeprom data for 5 GHz wlan in "art" partition.

Specification:

- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-06 20:26:57 +01:00
Chuanhong Guo
9dd7147f6b ath79: add support for Winchannel WB2000
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.

Specification:

- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338

Known issue:
5G ath9k led doesn't work due to commit ccab68f.

Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
   setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
   saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.50
3. Load and flash the firmware:
   tftp 0x80060000 fw.bin
   erase 0x9f050000 +$filesize
   cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
   reset

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>

merge
2018-12-06 20:26:30 +01:00
INAGAKI Hiroshi
e0c55760e6 ath79: fix ethernet configurations for I-O DATA ETG3-R
This commit fixes several issues in eth0 on ETG3-R, and solve slowdown
in NA(P)T speed.

- add gmac-config with correct configurations
- fix pll-data value

And I added ref clock-frequency.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-06 17:44:14 +01:00
Mathias Kresin
6e626477d5 ath79: drop unused mtd splitter
Neither the seama nor the wrgg splitter are used at the moment. Drop
them for now to not bloat the target from the beginning.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:47 +01:00
Mathias Kresin
dacd962cfd ath79: remove duplicate image build variables
Remove image build variables which are set to the same value as the
default image build recipe.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
Mathias Kresin
9d8fcab77a ath79: fix GL.iNet GL-AR300M sysupgrade
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.

Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
Mathias Kresin
8d6f128d39 ath79: add SoC or family compatible
Add missing SoC specific compatibles and/or inherit the family
compatibles like "ubnt,xm".

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
David Bauer
adfc8d8eca ath79: add AVM EVA firmware partition compatible
This commit adds firmware partition compatible for the
AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E.

This allows to select the correct mtdsplit parser
instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-06 13:28:22 +01:00
Petr Štetiar
bc41fb7efe ath79: Define firmware partition format to all boards where applicable
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-06 13:28:22 +01:00
Mathias Kresin
ffa55386f1 ramips: fix dtc compiler warnings
The latest dtc compiler considers nodes named i2c or spi as the
respective bus:

  /pinctrl/i2c: incorrect #address-cells for I2C bus
  /pinctrl/spi: incorrect #address-cells for SPI bus

Rename the node to fix the false positives.

Fix the spi node unit address for the DWR-512-B and UBNT-ER-e50 to get
rid of the following warning:

  SPI bus unit address format error, expected "n"

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chen Minqiang
295b37d207 ramips: mt76x8: select only the matching mt76 driver
Select the matching mt76 driver for the PCI wireless of the following
devices:

 - HiWiFi HC5861B
 - Mercury MAC1200R v2.0
 - Netgear AC1200 R6120
 - Buffalo WCR-1166DS
 - ZyXEL Keenetic Extra II
 - Wavlink WL-WN575A3

Because every device has selected the corresponding mt76 driver, we can
include kmod-mt7603 instead of the mt76 metapackage, which used for the
wireless of the mt7628 and mt7688 WiSoC.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[select kmod-mt7603 as target default package, add wireless driver for
WL-WN575A3]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chuanhong Guo
c36ec336a3 ath79: rename qca9533.dtsi to qca953x.dtsi
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chuanhong Guo
5563d49a39 ramips: disable sdhc for HC5661A
Currently OpenWrt doesn't support switching MT7628 into AP mode
(which is done by writing some undocumented registers in MTK SDK)
Without doing so, enabling SD breaks 4 FE ports and the SD controller
doesn't work since SD pins aren't configured correctly.

Disable SDHC on HC5661A to recover the 4 FE ports.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[drop the sdhci node completely]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Hans Dedecker
476336fe66 glibc: update to latest 2.27 commit (BZ #23927)
9f433fc791 CVE-2018-19591: if_nametoindex: Fix descriptor for overlong name [BZ #23927]

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-12-06 11:47:36 +01:00
Petr Štetiar
9da6cd40eb apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic diag.sh
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.

I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:

 base-files: diag.sh: Make it more generic towards DTS so it could be reused

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
2018-12-06 08:42:40 +01:00
Petr Štetiar
60dd181a76 base-files: diag.sh: Make it more generic towards DTS so it could be reused
I wanted to add status LEDs support to my imx6 based board and have
found out, that I could use diag.sh script found in ramips platform,
which seems to be also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

So I've extended the base diag.sh in a way, that if it detects any of
the DTS LED aliases, then it would use the generic DTS set_led_state
code.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-06 08:42:40 +01:00
David Bauer
68e59b61c6 kernel: add DT binding support to AVM EVA parser
It allows selecting split-firmware parser directly by
specifying image-format in the device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-06 08:42:40 +01:00
Rosen Penev
26dcaf58ee comgt: Fix 3g.sh permissions
3g.sh needs to be executable. 600 is not correct for that.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-12-06 08:42:39 +01:00
Jonathan Thibault
e93e2b6318 octeon: Evaluate board names in alphabetical order
Signed-off-by: Jonathan Thibault <jonathan@navigue.com>
2018-12-06 08:42:22 +01:00
Ram Chandra Jangir
9ed180b000 ipq806x: dts: Add support for RGMII RX and TX clock delays
This change enables support to select phy4 in RGMII mode and
enables RGMII TX/RX clock internal delays.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-12-06 08:15:50 +01:00
Ram Chandra Jangir
bf7719f22c kernel: ar83xx: Add support for three GMAC's connection
We have IPQ8064 AP161 board which has three GMAC's
 * RGMII x2
 * SGMII x1.
The existing ar8327 driver does not have support for
three GMAC's connection, hence this change adds support
for the same. This has been verified on AP148 and AP161
board.

Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-12-06 08:15:27 +01:00
Daniel Halmschlager
99e212171a ar71xx: Add usb drivers in Archer C7 v4/v5 images
This commit adds the default usb packages
- kmod-usb-core
- kmod-usb2
- kmod-usb-ledtrig-usbport
for Archer C7 v4 and v5.
(The C7 v5 configuration is based on the v4, therefore the change for v4
also applies for v5.)

Signed-off-by: Daniel Halmschlager <dh@dev.halms.at>
2018-12-05 21:30:37 +00:00
Michael Heimpold
d6ac8ca76c base-files: fix several bashisms
For equality test a simple = is sufficient, the == is
usually disregarded as bashism.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-12-05 22:16:52 +01:00
Marek Lindner
8ad45992ac ipq40xx: fix openmesh sysupgrade with tar content out of order
The tar extraction depends on the order in which the files
are added to the tar file. Since the order is not guaranteed
and depends on the host system, the combined mtd write fails
with sysupgrade images built on some systems.
Fix by changing to tar file order independent mtd write.

Fixes: 86e18f6706 ("ipq806x: add support for OpenMesh A42")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-12-05 09:40:32 +01:00
Steven Lin
2b4ac79a79 ipq40xx: add support for EnGenius EAP1300
SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
NOR:    32 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button
LEDS:   Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm

2. Load image via GUI

a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.

3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin

Signed-off-by: Steven Lin <steven.lin@senao.com>
2018-12-05 09:40:32 +01:00
Stijn Tintel
e261c8b764 brcm2708-gpu-fw: add fw required for camera module
To be able to use the camera module, start_x=1 has to be set in
config.txt. This will cause the bootloader to load the GPU firmware that
contain the extra video codecs. Install these firmware files.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-05 00:39:53 +02:00
Stijn Tintel
42ca32ad2f brcm2708-gpu-fw: update to git HEAD
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-05 00:09:14 +02:00
Stijn Tintel
93a14b8f2a kernel: add missing symbol
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-04 22:45:08 +02:00
Stijn Tintel
f208f77811 mac80211: fix brcmfmac on brcm2708
An upstream change broke brcmfmac when loaded with modparam roamoff=1.
As we are carrying a patch that enables roamoff by default on the
brcm2708 target to improve stability, wireless is currently broken
there. Add a patch to fix brcmfmac with roamoff=1.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-04 22:45:08 +02:00
Mathias Kresin
f381cbcb5f ramips: fix Netgear EX3700/EX3800 wireless driver selection
Fix the typo to select kmod-mt76x2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-04 20:40:27 +01:00
Felix Fietkau
4fd7882822 mt76: update to the latest version
5a5b396 mt76: throttle transmission of buffered multicast packets
8084323 mt7603: implement code for adjusting energy detect CCA thresholds
8929a6e mt7603: increase MCU timeout
f2ba65f mt7603: update firmware to 20161027164355
0ad998b mt7603: increase aggregation limits (based on vendor driver changes)
da00af0 mt7603: clear bit 18 in MT_SEC_SCR to fix ICV error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-12-04 12:28:56 +01:00
Rafał Miłecki
f98fde2db4 Revert "kernel: use add_mtd_partitions() helper when using OpenWrt parsers"
This reverts commit 7e88753ace.

Using subpartitions (hierarchical layout) resulted in calling MTD ops of
parent partition instead of master device ops. That was expected and
should work but testing revealed some bugs.

Apparently the way MTD_ERASE_PARTIAL is implemented in the OpenWrt
breaks something and using parent partition ops triggers using that
code.

On SmartRG SR400ac it was resulting in:
[  225.487519] jffs2: Erase at 0x01ac0000 failed immediately: errno -22
on the second boot (for some reason erasing was starting over) and it
was breaking flash access in a long term.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 15:50:26 +01:00
Pawel Dembicki
e9a9b7d1ed ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- WIFI 5G LED not working
- flash is very slow

The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang
40692f0fb5 ramips: mt7620: select only the matching mt76 driver
Because every device has selected the corresponding mt76 driver, we can
now disable the mt76 metapackage by default to make sure that other
devices (those don't need mt76) avoid selecting unwanted packages.

We can find the hardware specifies and determine the dependencies on
these sites:
  https://wikidevi.com/wiki/
  https://openwrt.org/toh/hwdata/

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang
7a32a73e52 ramips: mt7620: drop mt76 driver for boards without mt76 wireless
These boards don't have a mt76 wireless at all and don't need any of the
mt76 family drivers.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Mathias Kresin
55101877d3 ramips: mt7620: disable PCIe if nothing is attached
All boards neither expose the PCIe as Mini-PCIe nor have anything
attached to the PCIe Bus. Disable PCIe for those by dropping the node
from the dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-03 15:34:56 +01:00
Chen Minqiang
14b81c909f ramips: mt7620: add missing pci wifi nodes to dts files
These devices has pci wifi but not defined in dts:
 HC5761
 HC5861
 TINY-AC

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Rafał Miłecki
7e88753ace kernel: use add_mtd_partitions() helper when using OpenWrt parsers
This helper uses hierarchical partitions layout following the way
upstream parsers work. It's closer to what we should use when mainlining
our solutions. It also doesn't require hacky casting of struct
mtd_partition to the const.

THIS WILL AFFECT KERNEL PRINTING PARTITIONS IN THE LOG

Something like:
[    3.930158] 0x0000004e0000-0x000001fb0000 : "rootfs_data"
will get replaced by:
[    3.907338] Creating 1 MTD partitions on "rootfs":
[    3.912142] 0x00000031d400-0x000001ded400 : "rootfs_data"

It's important to understand that "rootfs_data" in above example is a
*subpartition* of the "rootfs" now. To get absolute addresses (e.g. for
some debugging purposes) one has to add them to the "rootfs", e.g.
[    3.912548] 0x0000001c2c00-0x000001fb0000 : "rootfs"

(0x1c2c00 + 0x31d400 = 0x4e0000)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 11:26:05 +01:00
Rafał Miłecki
e24983e710 kernel: backport 2 mtd partitioning fixes
This improves handling of subpartitions.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 10:34:12 +01:00
Florian Eckert
675eb747aa openvpn: add list element parsing
For the parameters tls-cipher and ncp-ciphers more than one option can
be used in the OpenVPN configuration, separated by a colon, which should
be implemented as a list in order to configure it more clearly. By
adding the new OPENVPN_LIST option to the openvpn.options file with the
tls-cipher and ncp-cipher parameters, uci can now add this option as a
"list" and the init script will generate the appropriate OpenVPN
configuration from it.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2018-12-03 09:54:03 +01:00
Rafał Miłecki
966ba6daa4 kernel: fix downloading rcX releases
They are no longer stored in the "testing" subdirectory and are not
available as .tar.xz archives. If -rc is detected download it from the
git.kernel.org and use .tar.gz.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-03 09:34:57 +01:00
Russell Senior
73127a878d ath79: add support for Ubiquiti AirRouter
Indoor low-power router with 2.4 GHz radio

CPU:    Atheros AR7241 rev 1
RAM:    32 MB
Flash:  8 MB NOR SPI
Switch: Atheros AR7240
Ports:  1x WAN, 4x LAN 10/100 Ethernet
WLAN:   Atheros AR9285 (2.4 GHz)
USB:    1x USB2 host port

Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.

UART settings: 115200, 8N1

                LEDs
        +--------------------------
        |
        |
        |
        |
        |
        |
        |
        |
    VCC | x x
     RX | * x
        | x x
        | x x
     TX | * x
    GND | * x
        |
        |
        |
        |
        +--------------------------
                ETHERNET PORTS

Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:56 +01:00
Russell Senior
20ec6af15e ath79: split ubnt outdoor device leds into separate dtsi
Move common LED configuration into a separate includible dtsi.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:49 +01:00
Eneas U de Queiroz
3fb45576ac cryptodev-linux: move from packages feed
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is actually a build dependency for /dev/crypto support in openssl.
Since it is a kernel module, it belongs here anyway.

- Removed Nikos Mavrogiannopoulos as maintainer.
- Streamlined make flags

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2018-12-03 07:50:24 +01:00
Tomasz Maciej Nowak
c288ad9c2b x86: make sysupgrade.tgz reachable again
Moving binding mount before check for saved sysupgrade configuration
made it unreachable. Fix it by moving binding mount after the check.

Fixes: f78b2616 (x86: mount writable bootfs)
Reported-by: Lucian Cristian <luci@powerneth.ro>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-12-03 07:38:20 +01:00
Jo-Philipp Wich
9808bd2799 Revert "base-files: fwtool: Fix wrong checksum on combined-image with metadata"
This reverts commit 41770add03.

The fwtool_check_image() procedure is used by `sysupgrade --test` which must
not alter the image under test in any way.

Currently, when the LuCI ui or any other sysupgrade wrapper first invokes
sysupgrade --test to verify the compatibility of the image and then calculates
the sha256sum over it, the resulting checksum will differ from the original
image since the test invocation will implicitely strip the metadata trailer.

To properly fix the underlying issue, the combined image checksumming code
must be modified to skip the metadata trailer.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-12-02 16:05:44 +01:00
Mathias Kresin
78ca6a5578 ramips: merge relocate compile into build recipe
Compile the loader if the relocate-kernel image recipe is used and get
rid of the legacy build code to do so.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-30 09:04:29 +01:00
Pawel Dembicki
465d57370f ramips: specify "firmware" partition format in JBOOT devices
Specify firmware partition format by compatible string.

List of devices:
-DWR-116-A1
-DWR-118-A2
-DWR-512-B
-DWR-921-C1
-LR-25G001

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-30 00:22:04 +01:00