ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
This commit is contained in:
parent
c2d50bdeb3
commit
1cb406d019
7 changed files with 55 additions and 4 deletions
|
@ -26,6 +26,11 @@ r7800)
|
|||
ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0"
|
||||
ucidef_set_led_ide "esata" "eSATA" "${board}:white:esata"
|
||||
;;
|
||||
fritz4040)
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" "phy1tpt"
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
|
||||
ucidef_set_led_switch "lan" "LAN" "${board}:green:lan" "switch0" "0x1e"
|
||||
;;
|
||||
nbg6817)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:amber:wifi2g" "phy1tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5g" "phy0tpt"
|
||||
|
|
|
@ -36,6 +36,11 @@ ea8500)
|
|||
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
|
||||
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
|
||||
;;
|
||||
fritz4040)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
||||
;;
|
||||
nbg6817)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
||||
ucidef_add_switch "switch0" \
|
||||
|
|
|
@ -46,6 +46,21 @@ board=$(ipq806x_board_name)
|
|||
|
||||
|
||||
case "$FIRMWARE" in
|
||||
"ath10k/pre-cal-ahb-a000000.wifi.bin")
|
||||
case "$board" in
|
||||
fritz4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath10k/pre-cal-ahb-a800000.wifi.bin")
|
||||
case "$board" in
|
||||
fritz4040)
|
||||
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
|
||||
"ath10k/cal-pci-0000:01:00.0.bin")
|
||||
case $board in
|
||||
c2600)
|
||||
|
|
|
@ -17,6 +17,9 @@ ipq806x_board_detect() {
|
|||
*"AP148")
|
||||
name="ap148"
|
||||
;;
|
||||
*"4040")
|
||||
name="fritz4040"
|
||||
;;
|
||||
*"C2600")
|
||||
name="c2600"
|
||||
;;
|
||||
|
|
|
@ -42,6 +42,9 @@ platform_do_upgrade() {
|
|||
MTD_CONFIG_ARGS="-s 0x200000"
|
||||
default_do_upgrade "$ARGV"
|
||||
;;
|
||||
*)
|
||||
default_do_upgrade "$ARGV"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
|
|
|
@ -272,7 +272,7 @@
|
|||
read-only;
|
||||
};
|
||||
partition11@2A0000 {
|
||||
label = "image"; /* firmware */
|
||||
label = "firmware";
|
||||
reg = <0x002A0000 0x01C60000>;
|
||||
};
|
||||
partition12@1f00000 {
|
||||
|
|
|
@ -5,8 +5,6 @@ include $(INCLUDE_DIR)/image.mk
|
|||
|
||||
UBIFS_OPTS = -m 2048 -e 124KiB -c 4096 -U -F
|
||||
|
||||
KERNEL_LOADADDR := 0x42208000
|
||||
|
||||
define Image/Prepare
|
||||
$(CP) $(LINUX_DIR)/vmlinux $(KDIR)/$(IMG_PREFIX)-vmlinux.elf
|
||||
endef
|
||||
|
@ -30,6 +28,7 @@ define Device/Default
|
|||
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
||||
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
|
||||
KERNEL_PREFIX := $$(IMAGE_PREFIX)
|
||||
KERNEL_LOADADDR = 0x42208000
|
||||
SUPPORTED_DEVICES = $$(BOARD_NAME)
|
||||
IMAGE/sysupgrade.tar = sysupgrade-tar | append-metadata
|
||||
endef
|
||||
|
@ -46,6 +45,12 @@ define Device/FitImage
|
|||
KERNEL_NAME := Image
|
||||
endef
|
||||
|
||||
define Device/FitImageLzma
|
||||
KERNEL_SUFFIX := -fit-uImage.itb
|
||||
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := Image
|
||||
endef
|
||||
|
||||
define Device/UbiFit
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES := nand-factory.ubi nand-sysupgrade.tar
|
||||
|
@ -165,6 +170,20 @@ define Device/EA8500
|
|||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
endef
|
||||
|
||||
define Device/FRITZ4040
|
||||
$(call Device/FitImageLzma)
|
||||
DEVICE_DTS := qcom-ipq4019-fritz4040
|
||||
KERNEL_LOADADDR := 0x80208000
|
||||
BLOCKSIZE := 4k
|
||||
PAGESIZE := 256
|
||||
BOARD_NAME := fritz4040
|
||||
DEVICE_TITLE := AVM Fritz!Box 4040
|
||||
IMAGE_SIZE := 29753344
|
||||
IMAGES = sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := kmod-usb-phy-qcom-ipq4019 ipq-wifi-fritz4040 fritz-tools u-boot-fritz4040
|
||||
endef
|
||||
|
||||
define Device/R7500
|
||||
$(call Device/DniImage)
|
||||
DEVICE_DTS := qcom-ipq8064-r7500
|
||||
|
@ -231,6 +250,7 @@ define Device/VR2600v
|
|||
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
|
||||
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817 VR2600v
|
||||
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 FRITZ4040 R7500 \
|
||||
R7500v2 R7800 NBG6817 VR2600v
|
||||
|
||||
$(eval $(call BuildImage))
|
||||
|
|
Loading…
Reference in a new issue