1cb406d019
This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
256 lines
7.2 KiB
Makefile
256 lines
7.2 KiB
Makefile
# Copyright (c) 2014 The Linux Foundation. All rights reserved.
|
|
#
|
|
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
UBIFS_OPTS = -m 2048 -e 124KiB -c 4096 -U -F
|
|
|
|
define Image/Prepare
|
|
$(CP) $(LINUX_DIR)/vmlinux $(KDIR)/$(IMG_PREFIX)-vmlinux.elf
|
|
endef
|
|
|
|
define Image/BuildKernel
|
|
$(CP) $(KDIR)/$(IMG_PREFIX)-vmlinux.elf $(BIN_DIR)
|
|
endef
|
|
|
|
define Image/Build/squashfs
|
|
cp $(KDIR)/root.squashfs $(KDIR)/root.squashfs-raw
|
|
$(call prepare_generic_squashfs,$(KDIR)/root.squashfs)
|
|
endef
|
|
|
|
define Image/Build
|
|
$(call Image/Build/$(1),$(1))
|
|
dd if=$(KDIR)/root.$(1) of=$(BIN_DIR)/$(IMG_PREFIX)-$(1)-root.img bs=2k conv=sync
|
|
endef
|
|
|
|
define Device/Default
|
|
PROFILES := Default
|
|
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
|
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
|
|
KERNEL_PREFIX := $$(IMAGE_PREFIX)
|
|
KERNEL_LOADADDR = 0x42208000
|
|
SUPPORTED_DEVICES = $$(BOARD_NAME)
|
|
IMAGE/sysupgrade.tar = sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/LegacyImage
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
endef
|
|
|
|
define Device/FitImage
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitImageLzma
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/UbiFit
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := nand-factory.ubi nand-sysupgrade.tar
|
|
IMAGE/nand-factory.ubi := append-ubi
|
|
IMAGE/nand-sysupgrade.tar := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/DniImage
|
|
PROFILES += $$(DEVICE_NAME)
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
NETGEAR_BOARD_ID :=
|
|
NETGEAR_HW_ID :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := factory.img sysupgrade.tar
|
|
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-ubi | netgear-dni
|
|
IMAGE/sysupgrade.tar := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | sysupgrade-tar kernel=$$$$@ | append-metadata
|
|
endef
|
|
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
|
|
define Device/TpSafeImage
|
|
PROFILES += $$(DEVICE_NAME)
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
TPLINK_BOARD_NAME :=
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
|
|
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata
|
|
endef
|
|
DEVICE_VARS += TPLINK_BOARD_NAME
|
|
|
|
define Device/ZyXELImage
|
|
PROFILES += $$(DEVICE_NAME)
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $${KERNEL_SIZE}
|
|
KERNEL_NAME := zImage
|
|
IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
|
|
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
|
|
IMAGE/mmcblk0p4-kernel.bin := append-kernel
|
|
endef
|
|
|
|
define Device/AP148
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_DTS := qcom-ipq8064-ap148
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap148
|
|
DEVICE_TITLE := Qualcomm AP148
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/AP148-legacy
|
|
$(call Device/LegacyImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_DTS := qcom-ipq8064-ap148
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap148
|
|
DEVICE_TITLE := Qualcomm AP148 (legacy)
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/C2600
|
|
$(call Device/TpSafeImage)
|
|
DEVICE_DTS := qcom-ipq8064-c2600
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := c2600
|
|
TPLINK_BOARD_NAME := C2600
|
|
DEVICE_TITLE := TP-Link Archer C2600
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/D7800
|
|
$(call Device/DniImage)
|
|
DEVICE_DTS := qcom-ipq8064-d7800
|
|
KERNEL_SIZE := 2097152
|
|
NETGEAR_BOARD_ID := D7800
|
|
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := d7800
|
|
DEVICE_TITLE := Netgear Nighthawk X4 D7800
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/DB149
|
|
$(call Device/FitImage)
|
|
DEVICE_DTS := qcom-ipq8064-db149
|
|
KERNEL_INSTALL := 1
|
|
BOARD_NAME := db149
|
|
DEVICE_TITLE := Qualcomm DB149
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/EA8500
|
|
$(call Device/LegacyImage)
|
|
DEVICE_DTS := qcom-ipq8064-ea8500
|
|
PAGESIZE := 2048
|
|
BLOCKSIZE := 128k
|
|
KERNEL_SIZE := 3072k
|
|
FILESYSTEMS := squashfs
|
|
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakeroot-hdr
|
|
PROFILES += $$(DEVICE_NAME)
|
|
BOARD_NAME := ea8500
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := factory.bin sysupgrade.tar
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi
|
|
DEVICE_TITLE := Linksys EA8500
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/FRITZ4040
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4019-fritz4040
|
|
KERNEL_LOADADDR := 0x80208000
|
|
BLOCKSIZE := 4k
|
|
PAGESIZE := 256
|
|
BOARD_NAME := fritz4040
|
|
DEVICE_TITLE := AVM Fritz!Box 4040
|
|
IMAGE_SIZE := 29753344
|
|
IMAGES = sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-usb-phy-qcom-ipq4019 ipq-wifi-fritz4040 fritz-tools u-boot-fritz4040
|
|
endef
|
|
|
|
define Device/R7500
|
|
$(call Device/DniImage)
|
|
DEVICE_DTS := qcom-ipq8064-r7500
|
|
KERNEL_SIZE := 2097152
|
|
NETGEAR_BOARD_ID := R7500
|
|
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := r7500
|
|
DEVICE_TITLE := Netgear Nighthawk X4 R7500
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/R7500v2
|
|
$(call Device/DniImage)
|
|
DEVICE_DTS := qcom-ipq8064-r7500v2
|
|
KERNEL_SIZE := 2097152
|
|
NETGEAR_BOARD_ID := R7500v2
|
|
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := r7500v2
|
|
DEVICE_TITLE := Netgear Nighthawk X4 R7500v2
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
endef
|
|
|
|
define Device/R7800
|
|
$(call Device/DniImage)
|
|
DEVICE_DTS := qcom-ipq8065-r7800
|
|
KERNEL_SIZE := 2097152
|
|
NETGEAR_BOARD_ID := R7800
|
|
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := r7800
|
|
DEVICE_TITLE := Netgear Nighthawk X4S R7800
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984
|
|
endef
|
|
|
|
define Device/NBG6817
|
|
DEVICE_DTS := qcom-ipq8065-nbg6817
|
|
KERNEL_SIZE := 4096k
|
|
BLOCKSIZE := 64k
|
|
BOARD_NAME := nbg6817
|
|
DEVICE_TITLE := ZyXEL NBG6817
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs losetup
|
|
$(call Device/ZyXELImage)
|
|
endef
|
|
|
|
define Device/VR2600v
|
|
PROFILES += $$(DEVICE_NAME)
|
|
FILESYSTEMS := squashfs
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL = kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
KERNEL_SIZE := 2097152
|
|
DEVICE_DTS := qcom-ipq8064-vr2600v
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := vr2600v
|
|
DEVICE_TITLE := TP-Link Archer VR2600v
|
|
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
|
|
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 FRITZ4040 R7500 \
|
|
R7500v2 R7800 NBG6817 VR2600v
|
|
|
|
$(eval $(call BuildImage))
|