KumiSystems/openwrtv4
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv4/target/linux/ath79/base-files/etc/board.d/02_network

197 lines
4.7 KiB
Text
Raw Normal View History

ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
#!/bin/sh
. /lib/functions/system.sh
. /lib/functions/uci-defaults.sh
ath79: add support for Phicomm K2T This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-13 13:14:49 +00:00
. /lib/functions/k2t.sh
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ath79_setup_interfaces()
{
local board="$1"
case "$board" in
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
avm,fritz300e|\
ath79: add support for OCEDO Koala This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-08 20:13:44 +00:00
ocedo,koala|\
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ocedo,raccoon|\
pcs,cap324|\
ath79: add support for Pisen WMM003N (Cloud Easy Power) Pisen WMM003N (sold under the name of Cloud Easy Power) is an AR9331-based router and power bank combo device. The device uses a stock firmware modified from OpenWRT for TP-Link TL-WR703N; however some GPIO definition is different on this device with TL-WR703N. An AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also added, and the stock Flash/RAM configuration is 8MiB/64MiB. The stock firmware is an old and heavily modified OpenWRT-based firmware, which has telnetd defaultly open, and the root password is "ifconfig" (quotation marks not included). The factory image format is not known yet, however the stock firmware ships the OpenWRT's sysupgrade command, and it can be used to install a newer firmware. Due to the lack of the access to the STM8 embedded controller, the SD slot is currently not usable (because it's muxed with the on-board USB port) and the AXP PMIC cannot be monitored. Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2018-08-12 14:32:01 +00:00
pisen,wmm003n|\
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,re450-v2|\
tplink,tl-mr10u|\
tplink,tl-mr3020-v1|\
ath79: add support for TP-Link MR-3040 v2 Add support for the ar71xx supported TP-Link MR-3040 v2. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-13 14:14:54 +00:00
tplink,tl-mr3040-v2|\
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr703n|\
ubnt,unifiac-lite|\
ubnt,unifiac-mesh|\
ubnt,unifi)
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ucidef_set_interface_lan "eth0"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
buffalo,wzr-hp-g450h)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
;;
ath79: add support for Buffalo BHR-4GRV2 Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros QCA9558. Ported from ar71xx target. Specification: - Qualcomm Atheros QCA9558 - 64 MB of RAM - 16 MB of Flash - 5x 10/100/1000 Ethernet - QCA8337N - 4x LEDs, 2x keys - UART header on PCB - Vcc, TX, RX, GND from LED side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Connect power cable to BHR-4GRV2 and turn on it 3. Access to "http://192.168.12.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新実行") button 5. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-06 16:59:23 +00:00
buffalo,bhr-4grv2)
ucidef_add_switch "switch0" \
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth0"
;;
ath79: add support of D-Link DIR-825 B1 Add support for the ar71xx supported D-Link DIR-825 B1 to ath79. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-09 17:49:29 +00:00
dlink,dir-825-b1)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
embeddedwireless,dorin)
ath79: add WLAN, Ethernet-Switch with LAN/WAN and Status LED to Dorin Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2018-06-05 14:56:48 +00:00
ucidef_add_switch "switch0" \
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
etactica,eg200)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_set_interface_lan "eth0" "dhcp"
ath79: fix glinet ar150 lan/wan ordering LAN and WAN were swapped Signed-off-by: John Crispin <john@phrozen.org>
2018-05-30 13:18:55 +00:00
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
glinet,ar150|\
glinet,ar300m)
ath79: initial gl-ar300m support Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
2018-05-27 05:37:22 +00:00
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
ath79: add support for I-O DATA WN-AC1167DGR I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz wifi - 2.4 GHz: SoC internal - 5 GHz: QCA988x - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1167DGR 2. Connect power cable to WN-AC1167DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-16 08:08:28 +00:00
iodata,wn-ac1167dgr|\
ath79: add support for I-O DATA WN-AC1600DGR2 I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-10 00:07:53 +00:00
iodata,wn-ac1600dgr2|\
pcs,cr5000)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
;;
ath79: add WNDR3700 and WNDR3700v2 Add support for WNDR3700 and WNDR3700v2. They share most things with WNDR3800. Only device IDs and partition structure needs to be set. Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has also the NA version of the factory image. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-08-11 22:18:53 +00:00
netgear,wndr3700|\
netgear,wndr3700v2|\
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
netgear,wndr3800)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
ucidef_add_switch_attr "switch0" "blinkrate" 2
ucidef_add_switch_port_attr "switch0" 1 led 6
ucidef_add_switch_port_attr "switch0" 2 led 9
ucidef_add_switch_port_attr "switch0" 5 led 2
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
netgear,wnr612-v2|\
on,n150r)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_set_interface_wan "eth0"
ath79: add Netgear WNR612 v2 Netgear WNR612 v2: - cpu Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 As there is a rebranded WNR612v2 called ON Networks N150R, add a dtsi which includes all device support, and add a separate dts for the device only (with a separate one for the subsequent N150R). Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-20 14:21:07 +00:00
ucidef_add_switch "switch0" \
"0@eth1" "1:lan" "2:lan" "3:lan:3" "4:lan:4"
ath79: Forward port support for CR3000 The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct NaaS offering. It was previously supported under the ar71xx branch and this forward ports that support with some notable differences: 1) Since reverting to stock firmware is now irrelevant there is is only a single openwrt image generated which uses the entire flash rather than preserving PowerCloud-specific partitions that are unneeded to openwrt-- those partitions will be erased and used by the openwrt image. 2) Rather than use a non-standard probe order for the ethernet devices, this image uses a set of 'ip link set ethX name ethY' commands very early in preinit (before the network is used at all), in order to have the the switch and Wan use the same ethernet names as in previous images. 3) /etc/config/wireless will need to be regenerated as the path to the wireless device has changed due to differences in ath79 DT for ar93x compared to ar71xx images. 4) eth0 is wan and eth1 is lan (switch) Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-28 12:57:22 +00:00
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
pcs,cr3000)
ath79: Forward port support for CR3000 The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct NaaS offering. It was previously supported under the ar71xx branch and this forward ports that support with some notable differences: 1) Since reverting to stock firmware is now irrelevant there is is only a single openwrt image generated which uses the entire flash rather than preserving PowerCloud-specific partitions that are unneeded to openwrt-- those partitions will be erased and used by the openwrt image. 2) Rather than use a non-standard probe order for the ethernet devices, this image uses a set of 'ip link set ethX name ethY' commands very early in preinit (before the network is used at all), in order to have the the switch and Wan use the same ethernet names as in previous images. 3) /etc/config/wireless will need to be regenerated as the path to the wireless device has changed due to differences in ath79 DT for ar93x compared to ar71xx images. 4) eth0 is wan and eth1 is lan (switch) Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-28 12:57:22 +00:00
ucidef_add_switch "switch0" \
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
ucidef_set_interface_wan "eth0"
ath79: add Netgear WNR612 v2 Netgear WNR612 v2: - cpu Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 As there is a rebranded WNR612v2 called ON Networks N150R, add a dtsi which includes all device support, and add a separate dts for the device only (with a separate one for the subsequent N150R). Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-20 14:21:07 +00:00
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
phicomm,k2t)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_add_switch "switch0" \
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
;;
ath79: add support for TP-Link TL-WDR4900 v2 Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 8 MB - RAM: 128 MB - Ethernet: AR8327N with 5 GE ports. - Wireless radio: QCA9558 for 2.4G and AR9580 for 5G. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-09 04:29:28 +00:00
tplink,archer-c7-v2|\
tplink,tl-wdr4900-v2)
ath79: add support for TP-Link Archer c7 v2 Signed-off-by: Sibren Vasse <github@sibrenvasse.nl>
2018-06-26 05:25:33 +00:00
ucidef_add_switch "switch0" \
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
;;
ath79: add support for Buffalo WHR-G301N Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240. Ported from ar71xx target. Specification: - Atheros AR7240 - 32 MB of RAM - 4 MB of Flash - 2.4 GHz 2T2R wifi - 5x 10/100 Mbps Ethernet - 9x LEDs, 4x keys - LED: 8x gpio-leds, 1x ath9k-leds - key: 2x buttons, 1x slide switch - UART header on PCB - Vcc, GND, TX, RX from LEDs side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WHR-G301N 2. Connect power cable to WHR-G301N and turn on it 3. Access to "http://192.168.11.1/" and open firmware update page ("ファーム更新") 4. Select the OpenWrt factory image and click execute ("実行") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [fix the SUPPORTED_DEVICES to be compatible with the ar71xx image] Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-14 06:01:05 +00:00
buffalo,whr-g301n|\
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-mr3220-v1|\
tplink,tl-mr3420-v1|\
tplink,tl-wr841-v7)
ath79: add support for more AR7241 TP-Link boards Its common AP99(AR7241) platform with following devices: TP-Link TL-WR841N/ND v7 (SoC AR7241 / Wifi AR9287 / without USB) TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support) TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support) Signed-off-by: Dmytro Smyrnov <dioptimizer@hotmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-26 14:01:47 +00:00
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wdr3600|\
tplink,tl-wdr4300)
ath79: preliminary support for TP-Link WDR3600 / WDR4300 (AR9344) working: - leds - buttons - lan / wan - usb (hub port 1 + 2) - wifi 5g - sysupgrade - ... not working: - wifi 2g Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-05-18 16:06:03 +00:00
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr1043nd-v1)
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr1043nd-v2|\
tplink,tl-wr1043nd-v3)
ath79: add support for tl-wr1043nd v2/v3 Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 17:22:13 +00:00
ucidef_add_switch "switch0" \
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr1043nd-v4)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr2543-v1)
ath79: add tl-wr2543-v1 support to switch between wlan leds we need a userspace implementation Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-20 22:02:10 +00:00
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
;;
ath79: Fix led nodes for TL-WR740N v2 and add its clones This patch did the following things: 1. Separate ath9k-leds out of gpio leds so that all other leds will work before ath9k loded (e.g. during preinit/init stage). 2. Rename wps led to qss since that's how TP-Link mark it. 3. Rename LED prefix to tp-link because that dts is shared by many devices. 4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1. (This will require a forced sysupgrade if you comes from the previous wr740n v2 image.) 5. Remove SUPPORTED_DEVICES. (tl-wr740n-v2 doesn't exist anywhere so it's useless.) 6. Add all WR741ND v1 clones found in ar71xx. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 05:17:44 +00:00
tplink,tl-wr740n-v1|\
tplink,tl-wr740n-v3|\
tplink,tl-wr741-v1|\
tplink,tl-wr743nd-v1|\
tplink,tl-wr841-v5|\
tplink,tl-wr941-v4)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_set_interface_wan "eth0"
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ucidef_add_switch "switch0" \
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr740nd-v4|\
ath79: fix leds and network for TP-Link TL-WR841 v9/v11 Adding tl-wr841-v11 and the rename of tl-wr841n-v9 to tl-wr841-v9 in 01_leds and 02_network script files are missing in commits cc35c91 and 8db6522. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [merged with identical case in 02_network] Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 08:30:17 +00:00
tplink,tl-wr741nd-v4|\
tplink,tl-wr841-v9|\
tplink,tl-wr841-v11)
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ucidef_set_interface_wan "eth0"
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ucidef_add_switch "switch0" \
ath79: put all devices in alphabetical order in scripts And remove specifying lan interfaces as eth1.1 because this is handled by ucidef_add_switch. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
;;
ath79: add support for TP-Link TL-WR941N/ND v2/v3 Specification: - SoC: Atheros AR9132 - Flash: 4 MB - RAM: 32 MB - Ethernet: Marvell 88E6060 with 5 FE ports. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-13 12:32:02 +00:00
tplink,tl-wr941-v2)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
esac
}
ath79: add AVM FRITZ!WLAN Repeater 300E No known issues, everything works fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-02 18:28:50 +00:00
ath79_setup_macs()
{
local board="$1"
case "$board" in
avm,fritz300e)
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
;;
ath79: add support of D-Link DIR-825 B1 Add support for the ar71xx supported D-Link DIR-825 B1 to ath79. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2018-08-09 17:49:29 +00:00
dlink,dir-825-b1)
lan_mac=$(mtd_get_mac_text "caldata" 65440)
wan_mac=$(mtd_get_mac_text "caldata" 65460)
;;
ath79: add support for I-O DATA WN-AC1167DGR I-O DATA WN-AC1167DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM (DDR2) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz wifi - 2.4 GHz: SoC internal - 5 GHz: QCA988x - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1167DGR 2. Connect power cable to WN-AC1167DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-16 08:08:28 +00:00
iodata,wn-ac1167dgr|\
ath79: add support for I-O DATA WN-AC1600DGR2 I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-10 00:07:53 +00:00
iodata,wn-ac1600dgr2)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
;;
ath79: Add wifi to WNDR3700, WNDR3700v2 and WNDR3800 Add ath9k wifi capabilities to WNDR3700 family. * use kmod-owl-loader to load firmware from "art" * add wifi to DTS * add wifi LEDs Avoid using the same MAC for eth0 LAN and wlan0 by toggling the eth0 MAC into a locally administered MAC. That is currently done by in user-space by adding a uci config item into /etc/config/network (More elegant solution might be setting it already in preinit phase.) Known issues: * wifi firmware file may not get created on the first boot after flashing on time to bring wifi normally up. Likely the overlay jffs2 is not yet ready for creating the firmware file. "wifi up" may still bring wifi up. Wifi will work normally at subsequent boots. * phy0 and phy1 may get assigned mixed, so that phy0 may be the 5GHz radio instead of the normal 2.4GHz, and vice versa for phy1. Does not happen always, but may happen. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [fix the wifi unit address in the dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-13 20:10:47 +00:00
netgear,wndr3700|\
netgear,wndr3700v2|\
netgear,wndr3800)
lan_mac=$(macaddr_setbit_la "$(mtd_get_mac_binary art 0)")
;;
ath79: add support for Phicomm K2T This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-13 13:14:49 +00:00
phicomm,k2t)
lan_mac=$(k2t_get_mac "lan_mac")
wan_mac=$(k2t_get_mac "wan_mac")
;;
ath79: remove quotes for boardname in scripts Quotes are not required in case statements. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-02 07:14:10 +00:00
tplink,tl-wr1043nd-v4)
ath79: small wr1043nd-v4 fixes - fix sysupgrade check - move usb to v4 dts because v5 doesn't have it - make wan mac address behave like ar71xx target - add orange wan led support, it can be userspace activated like: on: echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger off: echo none > /sys/class/leds/tp-link\:orange\:wan/trigger Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-23 07:52:10 +00:00
base_mac=$(mtd_get_mac_binary product-info 8)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
ath79: add support for TP-Link TL-WR941N/ND v2/v3 Specification: - SoC: Atheros AR9132 - Flash: 4 MB - RAM: 32 MB - Ethernet: Marvell 88E6060 with 5 FE ports. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-08-13 12:32:02 +00:00
tplink,tl-wr941-v2)
base_mac=$(mtd_get_mac_binary u-boot 130048)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
ath79: add AVM FRITZ!WLAN Repeater 300E No known issues, everything works fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-02 18:28:50 +00:00
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
ath79: add support for Phicomm K2T This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-13 13:14:49 +00:00
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
ath79: add AVM FRITZ!WLAN Repeater 300E No known issues, everything works fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-02 18:28:50 +00:00
}
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
board_config_update
board=$(board_name)
ath79_setup_interfaces $board
ath79: add AVM FRITZ!WLAN Repeater 300E No known issues, everything works fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-02 18:28:50 +00:00
ath79_setup_macs $board
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
board_config_flush
exit 0
Reference in a new issue Copy permalink