openwrtv4/package/network/utils/iw/patches/001-nl80211_h_sync.patch

--- a/nl80211.h
+++ b/nl80211.h
@@ -27,6 +27,8 @@
 
 #include <linux/types.h>
 
+#define NL80211_GENL_NAME "nl80211"
+
 /**
  * DOC: Station handling
  *
@@ -1429,6 +1431,11 @@ enum nl80211_commands {
  * @NL80211_ATTR_MAX_CRIT_PROT_DURATION: duration in milliseconds in which
  *      the connection should have increased reliability (u16).
  *
+ * @NL80211_ATTR_PEER_AID: Association ID for the peer TDLS station (u16).
+ *	This is similar to @NL80211_ATTR_STA_AID but with a difference of being
+ *	allowed to be used with the first @NL80211_CMD_SET_STATION command to
+ *	update a TDLS peer STA entry.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1727,6 +1734,10 @@ enum nl80211_attrs {
 	NL80211_ATTR_CRIT_PROT_ID,
 	NL80211_ATTR_MAX_CRIT_PROT_DURATION,
 
+	NL80211_ATTR_PEER_AID,
+
+	NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -1991,6 +2002,10 @@ enum nl80211_sta_bss_param {
  * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode
  * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards
  *	non-peer STA
+ * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
+ *	Contains a nested array of signal strength attributes (u8, dBm)
+ * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
+ *	Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
  * @__NL80211_STA_INFO_AFTER_LAST: internal
  * @NL80211_STA_INFO_MAX: highest possible station info attribute
  */
@@ -2020,6 +2035,8 @@ enum nl80211_sta_info {
 	NL80211_STA_INFO_NONPEER_PM,
 	NL80211_STA_INFO_RX_BYTES64,
 	NL80211_STA_INFO_TX_BYTES64,
+	NL80211_STA_INFO_CHAIN_SIGNAL,
+	NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
 
 	/* keep last */
 	__NL80211_STA_INFO_AFTER_LAST,
@@ -2413,6 +2430,8 @@ enum nl80211_survey_info {
  * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
  * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
  *	overrides all other flags.
+ * @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address
+ *	and ACK incoming unicast packets.
  *
  * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
  * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
@@ -2424,6 +2443,7 @@ enum nl80211_mntr_flags {
 	NL80211_MNTR_FLAG_CONTROL,
 	NL80211_MNTR_FLAG_OTHER_BSS,
 	NL80211_MNTR_FLAG_COOK_FRAMES,
+	NL80211_MNTR_FLAG_ACTIVE,
 
 	/* keep last */
 	__NL80211_MNTR_FLAG_AFTER_LAST,
@@ -2559,6 +2579,10 @@ enum nl80211_mesh_power_mode {
  *
  * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs)
  *
+ * @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've
+ *	established peering with for longer than this time (in seconds), then
+ *	remove it from the STA's list of peers.  Default is 30 minutes.
+ *
  * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_meshconf_params {
@@ -2590,6 +2614,7 @@ enum nl80211_meshconf_params {
 	NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL,
 	NL80211_MESHCONF_POWER_MODE,
 	NL80211_MESHCONF_AWAKE_WINDOW,
+	NL80211_MESHCONF_PLINK_TIMEOUT,
 
 	/* keep last */
 	__NL80211_MESHCONF_ATTR_AFTER_LAST,
@@ -2637,6 +2662,10 @@ enum nl80211_meshconf_params {
  * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will
  *	implement an MPM which handles peer allocation and state.
  *
+ * @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication
+ *	method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE).
+ *	Default is no authentication method required.
+ *
  * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
  *
  * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
@@ -2650,6 +2679,7 @@ enum nl80211_mesh_setup_params {
 	NL80211_MESH_SETUP_USERSPACE_AMPE,
 	NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC,
 	NL80211_MESH_SETUP_USERSPACE_MPM,
+	NL80211_MESH_SETUP_AUTH_PROTOCOL,
 
 	/* keep last */
 	__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
@@ -2730,6 +2760,8 @@ enum nl80211_channel_type {
  *	and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well
  * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
  *	attribute must be provided as well
+ * @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel
  */
 enum nl80211_chan_width {
 	NL80211_CHAN_WIDTH_20_NOHT,
@@ -2738,6 +2770,8 @@ enum nl80211_chan_width {
 	NL80211_CHAN_WIDTH_80,
 	NL80211_CHAN_WIDTH_80P80,
 	NL80211_CHAN_WIDTH_160,
+	NL80211_CHAN_WIDTH_5,
+	NL80211_CHAN_WIDTH_10,
 };
 
 /**
@@ -3028,11 +3062,11 @@ enum nl80211_tx_power_setting {
 };
 
 /**
- * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
- * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
- * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ * enum nl80211_packet_pattern_attr - packet pattern attribute
+ * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
  *	a zero bit are ignored
- * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
  *	a bit for each byte in the pattern. The lowest-order bit corresponds
  *	to the first byte of the pattern, but the bytes of the pattern are
  *	in a little-endian-like format, i.e. the 9th byte of the pattern
@@ -3043,23 +3077,23 @@ enum nl80211_tx_power_setting {
  *	Note that the pattern matching is done as though frames were not
  *	802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
  *	first (including SNAP header unpacking) and then matched.
- * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after
+ * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
  *	these fixed number of bytes of received packet
- * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
- * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ * @NUM_NL80211_PKTPAT: number of attributes
+ * @MAX_NL80211_PKTPAT: max attribute number
  */
-enum nl80211_wowlan_packet_pattern_attr {
-	__NL80211_WOWLAN_PKTPAT_INVALID,
-	NL80211_WOWLAN_PKTPAT_MASK,
-	NL80211_WOWLAN_PKTPAT_PATTERN,
-	NL80211_WOWLAN_PKTPAT_OFFSET,
+enum nl80211_packet_pattern_attr {
+	__NL80211_PKTPAT_INVALID,
+	NL80211_PKTPAT_MASK,
+	NL80211_PKTPAT_PATTERN,
+	NL80211_PKTPAT_OFFSET,
 
-	NUM_NL80211_WOWLAN_PKTPAT,
-	MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+	NUM_NL80211_PKTPAT,
+	MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
 };
 
 /**
- * struct nl80211_wowlan_pattern_support - pattern support information
+ * struct nl80211_pattern_support - packet pattern support information
  * @max_patterns: maximum number of patterns supported
  * @min_pattern_len: minimum length of each pattern
  * @max_pattern_len: maximum length of each pattern
@@ -3069,13 +3103,22 @@ enum nl80211_wowlan_packet_pattern_attr 
  * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
  * capability information given by the kernel to userspace.
  */
-struct nl80211_wowlan_pattern_support {
+struct nl80211_pattern_support {
 	__u32 max_patterns;
 	__u32 min_pattern_len;
 	__u32 max_pattern_len;
 	__u32 max_pkt_offset;
 } __attribute__((packed));
 
+/* only for backward compatibility */
+#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
+#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
+#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
+#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
+#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
+#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
+#define nl80211_wowlan_pattern_support nl80211_pattern_support
+
 /**
  * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
  * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
@@ -3095,7 +3138,7 @@ struct nl80211_wowlan_pattern_support {
  *	pattern matching is done after the packet is converted to the MSDU.
  *
  *	In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
- *	carrying a &struct nl80211_wowlan_pattern_support.
+ *	carrying a &struct nl80211_pattern_support.
  *
  *	When reporting wakeup. it is a u32 attribute containing the 0-based
  *	index of the pattern that caused the wakeup, in the patterns passed
@@ -3252,7 +3295,7 @@ struct nl80211_wowlan_tcp_data_token_fea
  * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
  *	u32 attribute holding the maximum length
  * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
- *	feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK
+ *	feature advertising. The mask works like @NL80211_PKTPAT_MASK
  *	but on the TCP payload only.
  * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
  * @MAX_NL80211_WOWLAN_TCP: highest attribute number
@@ -3556,6 +3599,10 @@ enum nl80211_ap_sme_features {
  *	Peering Management entity which may be implemented by registering for
  *	beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is
  *	still generated by the driver.
+ * @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor
+ *	interface. An active monitor interface behaves like a normal monitor
+ *	interface, but gets added to the driver. It ensures that incoming
+ *	unicast packets directed at the configured interface address get ACKed.
  */
 enum nl80211_feature_flags {
 	NL80211_FEATURE_SK_TX_STATUS			= 1 << 0,
@@ -3575,6 +3622,7 @@ enum nl80211_feature_flags {
 	NL80211_FEATURE_ADVERTISE_CHAN_LIMITS		= 1 << 14,
 	NL80211_FEATURE_FULL_AP_CLIENT_STATE		= 1 << 15,
 	NL80211_FEATURE_USERSPACE_MPM			= 1 << 16,
+	NL80211_FEATURE_ACTIVE_MONITOR			= 1 << 17,
 };
 
 /**