60cf71ede7
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct NaaS offering. It was previously supported under the ar71xx branch and this forward ports that support with some notable differences: 1) Since reverting to stock firmware is now irrelevant there is is only a single openwrt image generated which uses the entire flash rather than preserving PowerCloud-specific partitions that are unneeded to openwrt-- those partitions will be erased and used by the openwrt image. 2) Rather than use a non-standard probe order for the ethernet devices, this image uses a set of 'ip link set ethX name ethY' commands very early in preinit (before the network is used at all), in order to have the the switch and Wan use the same ethernet names as in previous images. 3) /etc/config/wireless will need to be regenerated as the path to the wireless device has changed due to differences in ath79 DT for ar93x compared to ar71xx images. 4) eth0 is wan and eth1 is lan (switch) Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
172 lines
2.8 KiB
Text
172 lines
2.8 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9341.dtsi"
|
|
|
|
/ {
|
|
model = "PowerCloud Systems CR3000";
|
|
compatible = "pcs,cr3000", "qca,ar9341";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-status = &status;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&jtag_disable_pins>;
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status: power {
|
|
label = "pcs:amber:power";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan2g {
|
|
label = "pcs:blue:wlan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wan {
|
|
label = "pcs:blue:wan";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
lan1 {
|
|
label = "pcs:blue:lan1";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
lan2 {
|
|
label = "pcs:blue:lan2";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
lan3 {
|
|
label = "pcs:blue:lan3";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
|
|
lan4 {
|
|
label = "pcs:blue:lan4";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <25000000>;
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
num-cs = <1>;
|
|
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x050000 0x07a0000>;
|
|
};
|
|
|
|
art: partition@7f0000 {
|
|
label = "art";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x1002>;
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
mtd-mac-address-increment = <1>;
|
|
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy4>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
phy-mode = "gmii";
|
|
pll-data = <0x06000000 0x00000101 0x00001616>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|