PTP for gianfar can be built as a module. Create a package for it.
[juhosg: remove the mp85xx specific patch]
Patchwork: http://patchwork.openwrt.org/patch/3344/
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35706
[juhosg: move the fsl-pq-mdio driver into a separate package]
Patchwork: http://patchwork.openwrt.org/patch/3345/
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35705
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
Fixes spurious build issues when changing target CFLAGS for specific ABI
options (such as ARM's floating point ABI).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35683
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
SVN-Revision: 35671
Currently, most platforms define such helpers in their own diag.sh
implementation with almost identical code. By factoring out the
common ground it's possible to simplify maintainability and
homogenize the haptics over multiple platforms (so far as is
reasonably practicable, in a next step).
[juhosg:
- fix led_set_attr parameters in led_timer
- add led_morse and status_led_set_morse helpers
- add status_led_blink_{preinit,failsafe} helpers]
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35648
Add .tar.xz, .txz, and .orig.tar.xz as known extensions to dl_cleanup.py.
Signed-off-by: Ian Leonard <antonlacon@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35645
This is platform definition for the RB951G device. It's mostly rework
of RB2011UAS patchset with network taken from the RB751 patches.
The main difference is the flash layout used by this device.
[juhosg:
- remove dead code from mach-rb951g
- add "-2HnD" suffix to the machine name
- use a separate 615-MIPS-ath79-RB951G-support.patch]
Patchwork: http://patchwork.openwrt.org/patch/3257/
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35633
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
SVN-Revision: 35632
Adjust the "AutoLoad" number for the BGMAC module to be prior
to the switch modules. This probably isn't real important as
the modules are loaded in the correct order by preinit anyway.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35625
